PDA

View Full Version : The life of a watercooler is tough


JesusNipples
11-30-2000, 09:58 PM
After dumping water all over inside my case and using my floppy drive as a rain gutter (i knew it was useful for SOMETHING!) i've decided I will never ever put my pump inside my case again. However my cat seems to think it's ok for her to hang out in there now. I shooed her off and now she hates me. Oh what will I ever do?

------------------
Jesse Jack
Webmaster - MBW Wrestling
http://www.mbwwrestling.com

Will
11-30-2000, 10:19 PM
HAH! You sir have the funniest name ever ...

Sucks about your water setup, did it kill anything other than the floppy?

JesusNipples
12-01-2000, 12:27 AM
nah, not that i've noticed. I thought it would toast my little PC beeper speaker as that was where most of the water ran onto when it ran off the floppy drive. But even it's OK. I don't think it even hurt my floppy, but I haven't had a chance to test it. Shows how much I use it. Anyway, it's nice how drives are encased in sheet metal. They make better rain gutters than say, my voodoo 4 would.

------------------
Jesse Jack
Webmaster - MBW Wrestling
http://www.mbwwrestling.com

Will
12-01-2000, 12:35 AM
So why did exactly did it leak over the floppy, do you have giant tubes taht go all over your case?

Joe
12-01-2000, 09:08 AM
Don't under estimate the gutter power a good high end video card can provide http://www.procooling.com/ubb/smile.gif My V5-5500 would do just fine as a nice water duct if it was ever used as such http://www.procooling.com/ubb/smile.gif

Infact ask kevin he knows all bout using your video card to direct water flows http://www.procooling.com/ubb/biggrin.gif

------------------
C-ya
Joe - Owner/Editor www.ProCooling.com (http://www.ProCooling.com)
Where the Completely Addicted Come to Cool Off

Somebody set up us the bomb.

[This message has been edited by Joe (edited 12-01-2000).]

JesusNipples
12-01-2000, 10:37 AM
Well, I'm kinda new and stupid to this whole thing. I had got my new system and spent a lot of time testing it out of the box, and I bled it of air out of the box as well. So i figured I'd just put it in without draining it. Well this wasn't so easy, the only way it would fit is if I passed everything through the drive bay. And, if you've ever bought a rese-pump from OCwatercool, the outlet on the pump doesn't exactly fit the hose. I forced it on, but it was a little stretch. So here i am pushing this res through the drive cage and suddenly i feel something splash my arm.

It was kind of a retarded thing to do considering the next day I came home, drained it, cut the hoses shorter, had to bleed the air out of it again and start over =)

Joe
12-01-2000, 10:45 AM
wow funny you should mention that fitting on that pump, I was just noticing the same thing. It is big ( bigger then a normal 3/8") but I guess it seals damn good http://www.procooling.com/ubb/smile.gif

the thin wall ( 1/16" wall) silicone tubing I am using stretched JUST enuf to hold onto it. I am using some zip ties not to help seal just to make sure they dont slip off ( cause if you are using Zip ties to help make a seal.... you will be in trouble as water will go everywhere.)

------------------
C-ya
Joe - Owner/Editor www.ProCooling.com (http://www.ProCooling.com)
Where the Completely Addicted Come to Cool Off

Somebody set up us the bomb.

[This message has been edited by Joe (edited 12-01-2000).]

JesusNipples
12-02-2000, 02:59 AM
yeah. I had to use every trick in the book to get the supplied tubing on. I lubed it up with some vaseline while running the hose under the hottest water i could run and then i pushed with all my might until finally i got it on. But, like i said, it stretched the hose, so it comes off kinda easy. Especially now that it's all lubed up. I'm thinking of ways to make a better seal. Something safer but not permanent. Any ideas?

I'm already in love with this thing. I've never got my PIII 450 to run at over 500. It's incredibly addictive. I'm grilling it in at 517 right now.

twocpu
12-02-2000, 01:37 PM
Dip the hose end (about 2" of it) in boiling water for about 1 minute before trying to put it on. Don't put any lubrication on it. Grab the cool part of the hose & push it straight down until the hose slips over the fitting. Shove it on as far as you can & let it cool. It won't come off & will form fit to the pump fitting as it cools.

Originally posted by JesusNipples:
yeah. I had to use every trick in the book to get the supplied tubing on. I lubed it up with some vaseline while running the hose under the hottest water i could run and then i pushed with all my might until finally i got it on. But, like i said, it stretched the hose, so it comes off kinda easy. Especially now that it's all lubed up. I'm thinking of ways to make a better seal. Something safer but not permanent. Any ideas?

I'm already in love with this thing. I've never got my PIII 450 to run at over 500. It's incredibly addictive. I'm grilling it in at 517 right now.

Will
12-02-2000, 05:11 PM
Nice idea twocpu .... might just have to do that in "the setup" ...