ghetto res.
more ghetto res (2 loop).
more more ghetto res (eheim fitted).
currently i use a T line, since i switched to a mcp600.

:dome:
my first full cooper
http://perso.wanadoo.fr/superglide/142-4258_IMG.JPG

my first full plexiglass
http://perso.wanadoo.fr/superglide/AGF00007.JPG

my first cylindrical
http://perso.wanadoo.fr/superglide/151-5162_IMG.JPG

5"1/4
http://perso.wanadoo.fr/superglide/149-4920_IMG.JPG
:drool:
http://perso.wanadoo.fr/superglide/149-4917_IMG.JPG

& my page (divers realisation)
http://perso.wanadoo.fr/superglide/reservoir.htm

Those are fantastic! you've got really good skills with plexi pierreg60!

and that copper airtrap is dead sexy!

Yeah those are good looking.

speaking of which, do you make them for people, or just for fun?

looking around your home page, i got the impression that you may make them for people.

Sorry for my bad English I am french..........

thank you for the compliments

I manufacture for forumeurs and also for the fun

Great reservoirs everybody.

What type of material/glue do you use for putting plexi together?

for PMMA=>PMMA i use chlorophorm
for PMMA =>PMMA XT i use epoxy adhesive 2 composents

Thank you very much for those answers

pierreg60

how did you make that awsome copper reserivor?

a tube of Ø 40mm and dish of copper of 3mm polishing and thats all

(google traduction sorry)

"40mm OD tube of copper and some 3mm copper plate, soldered and polished" I think.

any other neat reserivors around?

Lo all, heres my custom side panel res, posted this up a while back...
http://www.asfs71.dsl.pipex.com/sideres1.jpg
http://www.asfs71.dsl.pipex.com/sideres2.jpg
http://www.asfs71.dsl.pipex.com/sideres3.jpg
http://www.asfs71.dsl.pipex.com/sideres4.jpg

I've got one that's a little out of the ordinary. I don't know if any of you have seen it before, I'm not too active on the various forums.

http://i5.photobucket.com/albums/y15...essedSmall.jpg

I built the case from stainless steel tubing. The far side of the case is the reservoir and the near side is pressurized for distribution. The pump draws from the bottom of the res, pushes through the radiators and into the pressurized side. All the waterblocks pick up from bungs in the side and return back to the reservoir. I did this one about two years ago, and I'm halfway through the next iteration right now.

That is awsome and nice LCD's

here is my res

http://frip.dk/ymmot/tank003m.JPG

nice you make that ?

yes I have made that res :)

I'm lazy and just use a DD res with hole drilled in the threads for better filling action:

http://phaestus.procooling.com/radbox/finished4.jpg

Not custom, but still high "bling factor.
Note that those are 1/2" barbs, rare for such a small res.
I got it at: www.performance-pcs.com

It works great on an Eheim 1048, but an Iwaki 20RZT overwhelms it. The air goes right through! The inner chamber is only 1-1/4" (D) X 4-3/4" (H).

This 'Res' will contain a small Cistern made from a carburator needle and seet and float. And a Mistmaker. :)

[IMG]http://i7.photobucket.com/albums/y29...n/S4010428.jpg[/IMG]

More pics here

Will do a Proj Log whent the enclosure plate is cut and bent.
:)

where did you get the plexi tube?

probably not the same place, but take a look at usplastic.com

Jon

From my dads work :D:D