My block project
1 Attachment(s)
Hi to all, I recognize a few members from overclockers. I'm throwing out my block plan for full scrutiny. I see there are a number of experienced millers here. So far I got a model made up and some materials and assorted tools ordered. I think you can tell what I'm doing by the pic. I have lots of patience when it comes to tools so you know I do expect this to take some time.
My biggest question is how many resharpenings do you think I will need to go through on my lathe when cutting the copper? The only endmilling in the copper would be around the two smaller exits. The top will be made from plastic. |
One big center inlet and two smaller outlets??? here is a block i did and am still remodeling:
http://www.dorrellco.com/aluminumWB4/004.JPG http://www.dorrellco.com/aluminumWB4/005.JPG http://www.dorrellco.com/aluminumWB4/006.JPG Worked great with the half assed 1/2"ID looking center inlet and the two 1/4" outlets. Going to oval ot out a little more later when I get the time. Have no idea about lath tooling although a vertical mills endmill should do the whole thing without needing sharpening if you are going to use a carbide endmill with coolant. |
man, thats a nice design. What about milling some more grooves in the block bottom itself?
|
It's one 1/2" center inlet and two 3/8" side outlets. The cone shape in the block itself will have more ridges than the model. They will be closer together ( about three per mm ) and more shallow. The distance between the cone shapes will need to be experimented with by making multiple tops. The distance in the model shown is approximately 1/4".
jaydee116, I don't think two 1/4" barbs will equal the same as one 1/2" so your flow may be a little restricted. When you dig it out wider are you going to switch to two 3/8" outlets? Also I'm planning on having my two outlets go directly to a res so they don't have to merge with adapters, is that how you did yours? |
Quote:
But yes, I will try different outlets non the less. I am going to try 1/8"ID all the way up to 1/2"ID to find the perfect match with the 1/2ID" inlet. Right now I have a 3/8"ID inlet and 1/4ID" outlets and it isn't working nearly aswell as the 1/2"In and 1/4" outs. Going to be a while before I can get back to my projrcts. Moving this week and not sure where I can set the mill back up yet. |
1 Attachment(s)
:D :D :D
I got a start on it. |
1/4" + 1/4" doesn't equal 1/2
hint: it involves pi volume of 1/4" = .196sqin volume of 3/8" = .442sqin volume of 1/2" = .785sqin so you'd need 4x 1/4" or 2x 3/8" to be roughly equal to 1/2" |
Quote:
|
sTOP WITH ALL THE EQUATIONS, Your making my head hurt.
that is one wild looking tool hold you got there. I would recommend using some coolant. If it were me, I would have programmed it in CNC and let the mill hack at it for a while. Good work, Hope it turns out. |
I pause to oil often and also back off alot and the spinning of the lathe helps cooling some. I do believe heat will be more of a problem when I switch to copper though.
|
1 Attachment(s)
I recently got a good deal on this table also, I use it on my drill press. Anyone know where to get a collet chuck with a straight shaft 3/4"?
|
have you tried www.wttool.com (wholsale tool)
or maybe www.jlindustrial.com (J & L Industrial Supply) Both sites are great for getting all kinds of machining goodies as well. Endmills, Incerts, Vises, Drill bits, All sorts of neat dangerouse stuffs |
1 Attachment(s)
Thanks for the links, browsing for tools = eye popin fun:D
Been carving away, |
1 Attachment(s)
Still carving away, don't need the collet chuck after all (My drill press is huge). What's the recommended rpm for endmilling?
|
Well, it depends on the endmill size, sure there is a formula for the "Right" cutter speed, but screw that. Small Endmills Need more RMP`s then larger endmills. Adjust your speed until you get chips, not dust. That is about the easyest way.and when doing maunual machining.
U do not want the endmill to try and CLIMB or pull on the material. Look up Cline milling and CLIMB milling. You want to CLINE mill on a manual. But as long as your getting good sized chips and not dust, or bogging donw your motor, your in the right ball park. |
Well I was set at 1900rpm with a 3/8" bit. The chips are kind of fine but it could be from the type of bit I'm using. It's a serrated rough center cutter with four flutes. My motor is not a worry as it's a 1hp belt drive. I was just curious if I should bump the speed down, especially when I get to the copper one. I got my channel depth in three passes.
|
|
I have got to say,that sureis nice looking, You did a bang up job. Now if only U lived close to me, Me having the CNC mill, and you haveing the lathe, we could really make some kick A$$ stuffs.
Nice job, now how does it preform? |
i must say that looks like a nice piece of work... definitely interested in seeing some numbers
|
1 Attachment(s)
This weekends project (when I'm sober;) ) ,
|
Quote:
|
it's Saturday night, have you done it yet? ;)
|
1 Attachment(s)
It's Sunday dinner time where I am, but I made some progress, with a lot of help from the coffee pot:D
|
I made a new top for larger barbs and I found some excellent gasket material. Here's a pic. What's the best tubing at 1/2" to stretch over a 5/8" O.D. barb?
http://www.theforumisdown.com/upload.../sealed up.jpg |
Tygon probably. But you will NOT be able to get that stuff off...LOL...you'll probably have to cut it off.... :D
|
All times are GMT -5. The time now is 11:30 PM. |
Powered by vBulletin® Version 3.7.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(C) 2005 ProCooling.com If we in some way offend you, insult you or your people, screw your mom, beat up your dad, or poop on your porch... we're sorry... we were probably really drunk... Oh and dont steal our content bitches! Don't give us a reason to pee in your open car window this summer...