Pro/Forums

Pro/Forums (http://forums.procooling.com/vbb/index.php)
-   Testing and Benchmarking (http://forums.procooling.com/vbb/forumdisplay.php?f=61)
-   -   who can help me make a test bed? (http://forums.procooling.com/vbb/showthread.php?t=14428)

567234ta 10-21-2007 01:56 AM

who can help me make a test bed?
 
id like to have block of copper be able to get pretty hot and be able to measure the watts going to it.

something that would be fairly accurate and be like 0-1200 watts or so.

Spaceraver 10-21-2007 12:44 PM

Re: who can help me make a test bed?
 
a stove should do that.

jaydee 10-21-2007 06:36 PM

Re: who can help me make a test bed?
 
How much money do you have to spend?

567234ta 10-23-2007 01:26 AM

Re: who can help me make a test bed?
 
Quote:

Originally Posted by jaydee
How much money do you have to spend?

i have as much as it would take. but i guess it would come to a point of is it worth it to me at some point.
what did you have in mind?

jaydee 10-23-2007 05:12 PM

Re: who can help me make a test bed?
 
Quote:

Originally Posted by 567234ta
i have as much as it would take. but i guess it would come to a point of is it worth it to me at some point.
what did you have in mind?

Depends on your goals. I left off with my last test bench at about $3,000USD in used parts and parts I fabbed myself. I was pretty happy with it. Results were pretty consistent with ph's.

What are you intentions with the test bench?

567234ta 10-23-2007 10:16 PM

Re: who can help me make a test bed?
 
Quote:

Originally Posted by jaydee
Depends on your goals. I left off with my last test bench at about $3,000USD in used parts and parts I fabbed myself. I was pretty happy with it. Results were pretty consistent with ph's.

What are you intentions with the test bench?

mainly to test heatsinks and do reviews of them. you must have a pretty elaborate set up.

what i would really like is a copper block i can mount a heatsink on and have a knob to control the watts with a digital readout that is telling me the exact watts of it. but something that can pretty much exceed any cpu out there. into the 1000 watt red hot range.

jaydee 10-24-2007 05:55 PM

Re: who can help me make a test bed?
 
Quote:

Originally Posted by 567234ta
mainly to test heatsinks and do reviews of them. you must have a pretty elaborate set up.

what i would really like is a copper block i can mount a heatsink on and have a knob to control the watts with a digital readout that is telling me the exact watts of it. but something that can pretty much exceed any cpu out there. into the 1000 watt red hot range.

We had a pretty long debate about die sims vs. computers for testing. The end result pretty much was use an actual computer. The problem with die sims is they do not represent a real CPU. Especially the new dual and quad cores. There are hot and cold spots all over those things. I die sim the heat is distributed pretty consistently over the entire die.

The hard part about using a computer is getting decent temps consistent temps. The hard part about a die sim is the construction of the die itself. You can't just throw any chunk of copper on and think it will work. You will want to make 3-4 different one's to try and replicate the different dies of the current CPU's. Single core, duel core, quad core and even tri core. Then you also have both AMD and Intel in which the designs are not similar and the heat sinks will react different on both brands.

If I was to start over I would buy a AMD mobo that would accept as many different AMD CPU's as possible and and Intel mobo that would accept as many Intel cpu's as possible. Then find one very good overclocking CPU for each and then buy a few other types of CPU's. Test the heat sinks on all of them and give a comparison. That would benefit the readers the most.

Might want to follow this technique: http://www.overclockers.com/articles1312/


If you are really set on the die sim approach then find a very good machinist and start designing some die's to match the current CPU's the best as possible. Use a simple heater cartridge and a variable power supply and use a high quality meters to read volts and do simple math to get the watts. Volts x Amps = Watts

Insulate them as best as possible and make sure they have a good solid mounting system. Also have the machinist make several extra die sims of each kind as the do wear out pretty fast being you have to remount the heat sinks several times.

567234ta 10-26-2007 02:18 AM

Re: who can help me make a test bed?
 
Quote:

Originally Posted by jaydee
We had a pretty long debate about die sims vs. computers for testing. The end result pretty much was use an actual computer. The problem with die sims is they do not represent a real CPU. Especially the new dual and quad cores. There are hot and cold spots all over those things. I die sim the heat is distributed pretty consistently over the entire die.

The hard part about using a computer is getting decent temps consistent temps. The hard part about a die sim is the construction of the die itself. You can't just throw any chunk of copper on and think it will work. You will want to make 3-4 different one's to try and replicate the different dies of the current CPU's. Single core, duel core, quad core and even tri core. Then you also have both AMD and Intel in which the designs are not similar and the heat sinks will react different on both brands.

If I was to start over I would buy a AMD mobo that would accept as many different AMD CPU's as possible and and Intel mobo that would accept as many Intel cpu's as possible. Then find one very good overclocking CPU for each and then buy a few other types of CPU's. Test the heat sinks on all of them and give a comparison. That would benefit the readers the most.

Might want to follow this technique: http://www.overclockers.com/articles1312/


If you are really set on the die sim approach then find a very good machinist and start designing some die's to match the current CPU's the best as possible. Use a simple heater cartridge and a variable power supply and use a high quality meters to read volts and do simple math to get the watts. Volts x Amps = Watts

Insulate them as best as possible and make sure they have a good solid mounting system. Also have the machinist make several extra die sims of each kind as the do wear out pretty fast being you have to remount the heat sinks several times.

thats excellent info, i probably should just use a few different cpus and mobos but i havent decided which route i will go yet. thanks for sharing Jaydee.


All times are GMT -5. The time now is 04:04 AM.

Powered by vBulletin® Version 3.7.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(C) 2005 ProCooling.com
If we in some way offend you, insult you or your people, screw your mom, beat up your dad, or poop on your porch... we're sorry... we were probably really drunk...
Oh and dont steal our content bitches! Don't give us a reason to pee in your open car window this summer...