"$hitblock" by Hara
1 Attachment(s)
After success and experience when designing this block with balinju, I'm contemplating cutting this block out of copper using common tools :evilaugh:
Name: Shitblock Fin length: 24mm fin width 1.5mm fins are pointed Base Thickness: 2mm Fin height (including pointed bit): 5mm This is a render |
1 Attachment(s)
The originality to other cathar clones is that this block is designed specifically for the tbred 'B' core. See the core in the centre.
|
1 Attachment(s)
The last 2 channels don't have the same height as the others. The last channel isn't pointed on both sides.
|
1 Attachment(s)
Problem 1: making a 10mm thick copper bar 7mm thick. Any suggestions?
This design lends itself to cathar's WW. I just need confirmation that the tbred 'B' core is in this orientation: Thanks for your support! |
That little drawing is probably the most useful piece of info that WC enthousiasts can have! Thanks! :D
|
1 Attachment(s)
Maybe this will help you more.
Thanks for the feedback. |
Quote:
The orientation of the T'Bred B shown in the socket hole picture is correct. The measurements in the Socket A picture by Aitor are slightly incorrect - they look to be an approximation of the actual measurements. Not bad, but out by up to 0.3mm in places which may be significant for some. How is the water entering the block? Side to side? Hard to make any suggestions without first knowing that. |
I thought about a 1.5mm slit. I chose 1.5mm instead of 2mm because there are 25.5mm of fins which are 24mm long. This block will not be cut using a mill. If I tell you, you won't believe me.
|
1 Attachment(s)
Cathar, do you think that 24mm long channels are enough? Keeping in mind they are 1.5mm thick and the cpu core orientation.
|
1 Attachment(s)
if i am understanding well how the input of water is going to be, i think you gonna have quite some death spots. correct me if i am wrong
|
I don't think that this design would have more deadspots. In fact I thought that there would be less. Don't count on my reasoning though.
|
24mm long channels will be fine. You could probably get away with less, say down to about 20mm with the CPU in that orientation.
|
Quote:
|
Quote:
Quote:
|
In your opinion, do you think that the pointed fins would help ppl?
|
LMMFAO ! .....$hitblock..now thats an original ANYWHERE!!!
|
The name does not do it justice, or maybe it does. I just clicked to see some crap don't mind me.:D
|
Quote:
|
Quote:
|
brings new meaning the the saying " even shit, can cool good, when applied properly" :D
|
1 Attachment(s)
The difficult task is to make the 10mm thick copper 7mm thick. I have a small drillpress. Could I attach a shitty xy table and 5mm 4 flute endmill and perform the following task? Is it possible. Would it damage the drill press severely?
Thanks for your input |
Quote:
;) |
What did you use? xy table? endmills?
|
Quote:
|
Quote:
I think that your "step" on the outer fins is in the wrong direction: you ought to leave it the same, or make it thinner: there's barely enough heat there to make much of a difference. |
All times are GMT -5. The time now is 04:03 PM. |
Powered by vBulletin® Version 3.7.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(C) 2005 ProCooling.com If we in some way offend you, insult you or your people, screw your mom, beat up your dad, or poop on your porch... we're sorry... we were probably really drunk... Oh and dont steal our content bitches! Don't give us a reason to pee in your open car window this summer...