Go Back   Pro/Forums > ProCooling Technical Discussions > Heatsink/ Heat Pipe / ThermoSiphon Cooling
Password
Register FAQ Members List Calendar Chat

Heatsink/ Heat Pipe / ThermoSiphon Cooling The cat will only make the mistake of putting its paw by your HSF once. :) Also the place to discuss the new high end heat pipe goodness.

Reply
Thread Tools
Unread 04-08-2004, 01:42 PM   #1
ChristopherBlue
Cooling Neophyte
 
Join Date: Apr 2004
Location: Enhasa, a beautiful city upon the floating continent of Zeal
Posts: 2
Default Do I have the right tools to lap my heatsinks? Lapping guide?

I have bought 220, 320, and 600 grit water-proof sandpaper (only kind with the right grits at my local hardware shop). Will that be sufficent to correctly lap an aluminum and/or copper heatsink? I also picked up a 1' by 1' sheet of glass and plexiglass to use as a hard, flat surface for lapping (I am not sure which would work better, glass or plexiglass so I got both). I also obtained a 1" by 1" square of glass and plexiglass to wrap the sandpaper over again for the purpose of having a hard, flat surface.

Do I have the right tools to get the job done?

Also, what is a good lapping guide?
ChristopherBlue is offline   Reply With Quote
Unread 04-08-2004, 01:55 PM   #2
bigben2k
Responsible for 2%
of all the posts here.
 
bigben2k's Avatar
 
Join Date: May 2002
Location: Texas, U.S.A.
Posts: 8,302
Default

There are many lapping guides available, but yes, you have everything.

One note: the piece of glass is great, but the reason that glass is usually advised is that not only is it cheap and easy to find, you can also look at a reflection over it, to determine if it is indeed flat: watch out for bumps (fault in glass).
bigben2k is offline   Reply With Quote
Unread 04-08-2004, 02:37 PM   #3
dax
Cooling Neophyte
 
dax's Avatar
 
Join Date: Nov 2001
Location: Ghent, Belgium
Posts: 83
Default

I would avoid the plexi. The glass plate might be flat. You could get some thicker plate glass, as that is ground flat most of the time (not always the case though!). An (better) alternative would be a granite plate (cheap surface plate from enco/grizzly, or just try to find some crap).

All depends on how flat you want to get it... the glass you have might be perfectly ok for your purpose
dax is offline   Reply With Quote
Unread 04-09-2004, 05:25 PM   #4
ChristopherBlue
Cooling Neophyte
 
Join Date: Apr 2004
Location: Enhasa, a beautiful city upon the floating continent of Zeal
Posts: 2
Default

I have found that the 1" by 1" glass piece is way too big for my purposes. I don't think my fingers can do a good job keeping things flat so what is a good object to use for sanding small areas?
ChristopherBlue is offline   Reply With Quote
Unread 04-16-2004, 09:44 PM   #5
AngryAlpaca
Cooling Savant
 
Join Date: Jan 2004
Location: Alberta
Posts: 631
Default

I believe the preffered method for lapping is putting the wet sandpaper down upon the big sheet of glass, and then rubbing the heatsink on that.
AngryAlpaca is offline   Reply With Quote
Unread 04-16-2004, 10:48 PM   #6
spawningvat
Cooling Neophyte
 
Join Date: May 2003
Location: reading
Posts: 7
Default

Hold up a sec. You might want to try some other stores for finer grit sandpaper. 600 grit is still very coarse, possibly more course than the machining that is already on my the heatsink. And if you start at 200-300 grit, you might actually gouge the heatsink, which is what your trying to remove in the first place.Walmart sells 1000, 1500, and 2000 grit wet/dry papers in their auto section, and most auto stores like advance auto or autozone have a fine grit sandpaper selection near the paints.

Use some soap too, it will help the heatsink slide easily, and wash the sandpaper off and rewet it to keep it from clogging.

also grip the heatsink as close to the bottom as possible, so as to prevent wobbling and messing up your lapping job. and try to move in a circle or in a figure 8 motion, and rotate the heatsink periodically to prevent taking off too much from area.

just wanted to double-check that your are moving the heatsink over a piece of wet sandpaper, stuck to a piece of glass. Do not put the heatsink in a vise/do not clamp the heatsink and try to move the flat piece of glass/sandpaper over it. The idea is to make the heatsink as flat as possible, so lots of light, repetitive strokes are better than a few heavy strokes, which might not be perfectly parrellel to the heatsink.

Post back if you have anymore questions.


later
sean

edited for spelling

Last edited by spawningvat; 04-16-2004 at 10:57 PM.
spawningvat is offline   Reply With Quote
Unread 04-17-2004, 05:21 PM   #7
Butcher
Thermophile
 
Join Date: May 2001
Location: UK
Posts: 1,064
Default

I like to start at 240 grit to get things flat, then work up to 1500 grit personally.
__________________
Once upon a time, in a land far far away...
Butcher is offline   Reply With Quote
Unread 04-19-2004, 08:31 PM   #8
dogbait
Cooling Neophyte
 
dogbait's Avatar
 
Join Date: Jun 2003
Location: London, UK
Posts: 70
Default

A squirt of soap on the wet paper I find helps keep the heatsink moving smoothly.
dogbait is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 06:31 PM.


Powered by vBulletin® Version 3.7.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(C) 2005 ProCooling.com
If we in some way offend you, insult you or your people, screw your mom, beat up your dad, or poop on your porch... we're sorry... we were probably really drunk...
Oh and dont steal our content bitches! Don't give us a reason to pee in your open car window this summer...