fs R12 liquid chiller (1450BTU\h).

#Rotor · 04-19-2004, 12:28 PM

compressor: Tecumseh AE121AL-733-B6

Basic B/M AE121AL
Old Model AE3414A
New Model AEA3414AXA
Voltage 115-60-1
Application HT-12
BTU/Hr 1450
Replacement (new) AEA3414AXA
Repl B/M AE121AL
Repl Voltage 115-60-1
Repl BTU/Hr 1450
Adapter Kit(s) -

Still in excellent condition. No pump though, includes an inline high flow cleanable filter.
Make me a reasonable offer... you pay shipping.
[edit to fix the heading, it is indeed an R12 unit, ]

pHaestus · 04-19-2004, 12:36 PM

So plug in a pump to those copper pipes, connect waterblocks, and freeze semiconductors?

Any estimate on how much a month it costs to run, how loud it is, or how cold you can make CPUs with it?

I feel the need to upgrade to "real man cooling" and this just might be the way for me to go

#Rotor · 04-19-2004, 01:12 PM

with a drift-0.8 on about 11.3v open air, no load... with clean water.

the unit itself , well not very load... but then not very quite ether... manageable

pHaestus · 04-19-2004, 01:37 PM

hmm that IS real man cooling

I presume coolant temps below zero sans pelt? How much below though?

I dunno if I can afford to power the chiller plus the pelt continuously though...

#Rotor · 04-19-2004, 02:04 PM

have not had this one on a properly rigged CPU but I can pretty much imagine it would chill the shit out of even a presshott....

proper insulation and running with antifreeze... I'd think sub zero full load on your 1700+ should be attainable without a TEC...

if you install a thermostat, it can be a real handy little gadget... I ran my chillers at about 10% Duty Cycle, mainly to save on bills... and that 10% was enough to get me very comfortably below ambient..... I stand correctable, but to me it seemed like the stretch where the returns where max is from +20 all the way down to about 0º. Anything below 0 and the returns begins to negate agains the costs of running at those temps....

my Duron600 from way back could do what it did at -3ºC taking the temp up to +15 only cost me about 50Mhz but the saving in that obviously made it very much worth my while to not run full blast all the time...

so ya.. it can be very economical, and it can be very expensive, depends on the "volume knob"...

Groth · 04-19-2004, 02:31 PM

Was it converted to R-134a? The compressor is designed for R-12...

#Rotor · 04-19-2004, 06:49 PM

no

the guy I got it from said it was R134... so I took his word for it...

I was wondering why this little devil had no trouble in kicking my chillers ass.....

Groth · 04-20-2004, 05:11 AM

My neighbor's an HVAC guy. Based on talking to him (and a few calculation of my own), it should handle a 100 W load at -20 C, maybe a bit colder depending on refrigerant charge.

Shame I'm broke.

pHaestus · 04-20-2004, 12:53 PM

Why are you selling it #rotor? Looks like a great unit. I am sorely tempted; could use -20C water

#Rotor · 04-20-2004, 01:07 PM

I'm in the midst of preparing to go to the other side of the world. Not really allowed to say much though....

Gizmologist · 04-21-2004, 01:54 PM

$125 + s/h?

#Rotor · 04-21-2004, 04:03 PM

you have yourself a deal. can I pm you with all my particulars... or shall we do email... (scm50scm50 at yah00 d0t c0m)

Gizmologist · 04-24-2004, 11:15 AM

No response to Private Message ='s no thanks?

_Siph

#Rotor · 04-24-2004, 11:43 AM

not at all... seems like my reply somehow never got to where it was aimed at... I re-sent it just now...

#Rotor · 04-25-2004, 10:04 AM

Gismo..
did any of my PM's get through ?

#Rotor · 04-26-2004, 10:15 PM

Gizmologist.... please let me know... Ph is also very interested in it.....

#Rotor · 04-28-2004, 01:59 PM

pHaestus looks like it's gona go to you...

pHaestus · 04-28-2004, 02:01 PM

Any word from gizmologist? Also could you be troubled to give me dimensions of this unit? Wondering how easily I can fit it into a family room

MadHacker · 04-28-2004, 02:01 PM

if no one else is interested....
can that get shipped to canada?

pHaestus · 04-28-2004, 02:02 PM

I'd guess so since #rotor is in ON. But you'll have to get in line

#Rotor · 04-28-2004, 02:05 PM

holy crap...... you guys where just sitting here finger on the tricker or what

canada is easy yes.... Ph hold on leme see if i can find a tape. else i'll put it besides something familier.... it's small though... the pics make it look big

pHaestus · 04-28-2004, 02:06 PM

Do you do paypal #rotor or you want a money order? I can get either to you today if you give me a shipping cost to S7H4Y1

#Rotor · 04-28-2004, 02:23 PM

i'm guestimating L: 31cm W: 27cm H: 27cm

#Rotor · 04-28-2004, 02:26 PM

money order is good.... I can not do paypal... leme check the shipping costs quickly

#Rotor · 04-28-2004, 03:18 PM

Regular Parcel
5 days
28.69

i'll PM you with my goods...

04-19-2004, 12:28 PM	#1
#Rotor Cooling Savant Join Date: Feb 2002 Location: Dione, sector 4s1256 Posts: 852	fs R12 liquid chiller (1450BTU\h). compressor: Tecumseh AE121AL-733-B6 Basic B/M AE121AL Old Model AE3414A New Model AEA3414AXA Voltage 115-60-1 Application HT-12 BTU/Hr 1450 Replacement (new) AEA3414AXA Repl B/M AE121AL Repl Voltage 115-60-1 Repl BTU/Hr 1450 Adapter Kit(s) - Still in excellent condition. No pump though, includes an inline high flow cleanable filter. Make me a reasonable offer... you pay shipping. [edit to fix the heading, it is indeed an R12 unit, ] __________________ There is no Spoon.... Last edited by #Rotor; 04-19-2004 at 06:59 PM.

04-19-2004, 12:36 PM	#2
pHaestus Big Player Making Big Money Join Date: Aug 2001 Location: irc.lostgeek.com #procooling.com Posts: 4,782	So plug in a pump to those copper pipes, connect waterblocks, and freeze semiconductors? Any estimate on how much a month it costs to run, how loud it is, or how cold you can make CPUs with it? I feel the need to upgrade to "real man cooling" and this just might be the way for me to go __________________ Getting paid like a biker with the best crank... -MF DOOM

04-19-2004, 01:12 PM	#3
#Rotor Cooling Savant Join Date: Feb 2002 Location: Dione, sector 4s1256 Posts: 852	with a drift-0.8 on about 11.3v open air, no load... with clean water. the unit itself , well not very load... but then not very quite ether... manageable __________________ There is no Spoon....

04-19-2004, 01:37 PM	#4
pHaestus Big Player Making Big Money Join Date: Aug 2001 Location: irc.lostgeek.com #procooling.com Posts: 4,782	hmm that IS real man cooling I presume coolant temps below zero sans pelt? How much below though? I dunno if I can afford to power the chiller plus the pelt continuously though... __________________ Getting paid like a biker with the best crank... -MF DOOM

04-19-2004, 02:04 PM	#5
#Rotor Cooling Savant Join Date: Feb 2002 Location: Dione, sector 4s1256 Posts: 852	have not had this one on a properly rigged CPU but I can pretty much imagine it would chill the shit out of even a presshott.... proper insulation and running with antifreeze... I'd think sub zero full load on your 1700+ should be attainable without a TEC... if you install a thermostat, it can be a real handy little gadget... I ran my chillers at about 10% Duty Cycle, mainly to save on bills... and that 10% was enough to get me very comfortably below ambient..... I stand correctable, but to me it seemed like the stretch where the returns where max is from +20 all the way down to about 0º. Anything below 0 and the returns begins to negate agains the costs of running at those temps.... my Duron600 from way back could do what it did at -3ºC taking the temp up to +15 only cost me about 50Mhz but the saving in that obviously made it very much worth my while to not run full blast all the time... so ya.. it can be very economical, and it can be very expensive, depends on the "volume knob"... __________________ There is no Spoon....

04-19-2004, 02:31 PM	#6
Groth Cooling Savant Join Date: Mar 2003 Location: MO Posts: 781	Was it converted to R-134a? The compressor is designed for R-12...

04-19-2004, 06:49 PM	#7
#Rotor Cooling Savant Join Date: Feb 2002 Location: Dione, sector 4s1256 Posts: 852	no the guy I got it from said it was R134... so I took his word for it... I was wondering why this little devil had no trouble in kicking my chillers ass..... __________________ There is no Spoon.... Last edited by #Rotor; 04-19-2004 at 06:56 PM.

04-20-2004, 05:11 AM	#8
Groth Cooling Savant Join Date: Mar 2003 Location: MO Posts: 781	My neighbor's an HVAC guy. Based on talking to him (and a few calculation of my own), it should handle a 100 W load at -20 C, maybe a bit colder depending on refrigerant charge. Shame I'm broke.

04-20-2004, 12:53 PM	#9
pHaestus Big Player Making Big Money Join Date: Aug 2001 Location: irc.lostgeek.com #procooling.com Posts: 4,782	Why are you selling it #rotor? Looks like a great unit. I am sorely tempted; could use -20C water __________________ Getting paid like a biker with the best crank... -MF DOOM

04-20-2004, 01:07 PM	#10
#Rotor Cooling Savant Join Date: Feb 2002 Location: Dione, sector 4s1256 Posts: 852	I'm in the midst of preparing to go to the other side of the world. Not really allowed to say much though.... __________________ There is no Spoon....

04-21-2004, 01:54 PM	#11
Gizmologist Cooling Neophyte Join Date: Apr 2003 Location: Washington D.C. area Posts: 13	$125 + s/h?

04-21-2004, 04:03 PM	#12
#Rotor Cooling Savant Join Date: Feb 2002 Location: Dione, sector 4s1256 Posts: 852	you have yourself a deal. can I pm you with all my particulars... or shall we do email... (scm50scm50 at yah00 d0t c0m) __________________ There is no Spoon....

04-24-2004, 11:15 AM	#13
Gizmologist Cooling Neophyte Join Date: Apr 2003 Location: Washington D.C. area Posts: 13	No response to Private Message ='s no thanks? _Siph

04-24-2004, 11:43 AM	#14
#Rotor Cooling Savant Join Date: Feb 2002 Location: Dione, sector 4s1256 Posts: 852	not at all... seems like my reply somehow never got to where it was aimed at... I re-sent it just now... __________________ There is no Spoon....

04-25-2004, 10:04 AM	#15
#Rotor Cooling Savant Join Date: Feb 2002 Location: Dione, sector 4s1256 Posts: 852	Gismo.. did any of my PM's get through ? __________________ There is no Spoon....

04-26-2004, 10:15 PM	#16
#Rotor Cooling Savant Join Date: Feb 2002 Location: Dione, sector 4s1256 Posts: 852	Gizmologist.... please let me know... Ph is also very interested in it..... __________________ There is no Spoon....

04-28-2004, 01:59 PM	#17
#Rotor Cooling Savant Join Date: Feb 2002 Location: Dione, sector 4s1256 Posts: 852	pHaestus looks like it's gona go to you... __________________ There is no Spoon....

04-28-2004, 02:01 PM	#18
pHaestus Big Player Making Big Money Join Date: Aug 2001 Location: irc.lostgeek.com #procooling.com Posts: 4,782	Any word from gizmologist? Also could you be troubled to give me dimensions of this unit? Wondering how easily I can fit it into a family room __________________ Getting paid like a biker with the best crank... -MF DOOM

04-28-2004, 02:01 PM	#19
MadHacker Cooling Savant Join Date: May 2003 Location: Okotoks, A.B. Canada Posts: 726	if no one else is interested.... can that get shipped to canada? __________________ "Great spirits have always encountered violent opposition from mediocre minds" - (Einstein)

04-28-2004, 02:02 PM	#20
pHaestus Big Player Making Big Money Join Date: Aug 2001 Location: irc.lostgeek.com #procooling.com Posts: 4,782	I'd guess so since #rotor is in ON. But you'll have to get in line __________________ Getting paid like a biker with the best crank... -MF DOOM

04-28-2004, 02:05 PM	#21
#Rotor Cooling Savant Join Date: Feb 2002 Location: Dione, sector 4s1256 Posts: 852	holy crap...... you guys where just sitting here finger on the tricker or what canada is easy yes.... Ph hold on leme see if i can find a tape. else i'll put it besides something familier.... it's small though... the pics make it look big __________________ There is no Spoon....

04-28-2004, 02:06 PM	#22
pHaestus Big Player Making Big Money Join Date: Aug 2001 Location: irc.lostgeek.com #procooling.com Posts: 4,782	Do you do paypal #rotor or you want a money order? I can get either to you today if you give me a shipping cost to S7H4Y1 __________________ Getting paid like a biker with the best crank... -MF DOOM

04-28-2004, 02:23 PM	#23
#Rotor Cooling Savant Join Date: Feb 2002 Location: Dione, sector 4s1256 Posts: 852	i'm guestimating L: 31cm W: 27cm H: 27cm __________________ There is no Spoon....

04-28-2004, 02:26 PM	#24
#Rotor Cooling Savant Join Date: Feb 2002 Location: Dione, sector 4s1256 Posts: 852	money order is good.... I can not do paypal... leme check the shipping costs quickly __________________ There is no Spoon....

04-28-2004, 03:18 PM	#25
#Rotor Cooling Savant Join Date: Feb 2002 Location: Dione, sector 4s1256 Posts: 852	Regular Parcel 5 days 28.69 i'll PM you with my goods... __________________ There is no Spoon....

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)