Go Back   Pro/Forums > ProCooling Technical Discussions > Xtreme Cooling
Password
Register FAQ Members List Calendar JavaChat Mark Forums Read

Xtreme Cooling LN2, Dry Ice, Peltiers, etc... All the usual suspects

Reply
Thread Tools
Unread 07-22-2003, 12:06 PM   #1
hydrogen18
Cooling Savant
 
hydrogen18's Avatar
 
Join Date: Feb 2003
Location: USA
Posts: 248
Default Easy way to power many pelts without expensive power supply.

The biggest problemwith pelts is obviously the cost and effecieny of the power supply. Now, since peltiers are very simple loads and care very little about the quality of the power coming to them, why not hook 10x 12 volt pelts or 5x 24 volt up in series, thus making a 120 VDC peltier. Then simply take 2 or 3 large bridge rectifiers hook them to the 120 VAC line, then hook the peltiers to the other side. This would cost very little and provides loads of peltier cooling. It is also very small. The only problem I can forsee is that you would be saying "wtf am i supposed to do with 5 or 10 pelts?". Also 120 VDC is very dangerous as it is not a self quenching arc. Any suggestions/thoughts to my idea?
hydrogen18 is offline   Reply With Quote
Unread 07-22-2003, 12:37 PM   #2
winewood
Cooling Savant
 
winewood's Avatar
 
Join Date: Nov 2002
Location: in my chair
Posts: 574
Default

The easiest application I can see is a water cooler.
__________________
-winewood-
winewood is offline   Reply With Quote
Unread 07-23-2003, 06:38 AM   #3
]JR[
Cooling Neophyte
 
Join Date: Apr 2003
Location: UK
Posts: 74
Default

Unfortunately the AC ripple would destroy the TECs fairly rapidly, and a capacitor to smooth 120v @ 10amps (need like 200miliF) would cost more than a dedicated smps. The beauty of smps is the frequency is many kHz rather than 60Hz, which makes the capacitors (and transformers) much smaller, and therefore cheaper, at the smaller cost of some beefy fets...

]JR[
]JR[ is offline   Reply With Quote
Unread 07-23-2003, 06:50 AM   #4
]JR[
Cooling Neophyte
 
Join Date: Apr 2003
Location: UK
Posts: 74
Default

Actually 40000uF might do, although a 6000uF capacitor with a high enough voltage rating is £100/$160, and you would need 7 of them!

]JR[
]JR[ is offline   Reply With Quote
Unread 07-23-2003, 06:55 AM   #5
Boli
Cooling Savant
 
Boli's Avatar
 
Join Date: Apr 2003
Location: Blackburn / Dundee
Posts: 451
Default

Can Pelts even work off AC current?

I don;t know much about the specs of them but arn't they made up of diodes?

An LED is a type of Diode and that won't work if installed the wrong way wrong round and I'm prepared to bet they won;t work off AC.

Won't you have simmilar problems with an AC current though them
Boli is offline   Reply With Quote
Unread 07-23-2003, 09:09 AM   #6
bigben2k
Responsible for 2%
of all the posts here.
 
bigben2k's Avatar
 
Join Date: May 2002
Location: Texas, U.S.A.
Posts: 8,302
Default

Quote:
Originally posted by Boli
Can Pelts even work off AC current?

I don;t know much about the specs of them but arn't they made up of diodes?

An LED is a type of Diode and that won't work if installed the wrong way wrong round and I'm prepared to bet they won;t work off AC.
Boli, if you look at the first post, there's a mention of a "bridge rectifier".

A bridge rectifier is a set of 4 power diodes that turn the negative voltage of an AC wave into a positive one. If you've seen a sine wave, try to picture it, with the part that's under zero reversed to be positive, resulting in what looks like a mountain range.

Then, as ]JR[ correctly pointed, what you have left is a voltage that goes up and down, from (near) zero, up to 170+ volts (on a 110 Vac outlet), which is not unlike a switched signal. So to smooth out the curve, we add capacitors, which get charged at the wave's peak, and discharge at the wave's low point, to result in an almost flat DC output. TECs live longer with a true DC output.

Limitations are described accurately by ]JR[.
bigben2k is offline   Reply With Quote
Unread 07-23-2003, 09:56 AM   #7
MeltMan
Cooling Savant
 
MeltMan's Avatar
 
Join Date: Aug 2001
Location: KS
Posts: 374
Default Re: Easy way to power many pelts without expensive power supply.

Quote:
Originally posted by hydrogen18
why not hook 10x 12 volt pelts or 5x 24 volt up in series, thus making a 120 VDC peltier. Then simply take 2 or 3 large bridge rectifiers hook them to the 120 VAC line.
You need to remember that 120V is rated in RMS values. When rectified to DC its more like 170VDC with massive ripple. That, combined with the huge amperage you'll pull... It's just not feasable.

The electric company would be giving you kisses though...
__________________
MeltMan
Lurker Supreme!
MeltMan is offline   Reply With Quote
Unread 07-23-2003, 11:16 AM   #8
hydrogen18
Cooling Savant
 
hydrogen18's Avatar
 
Join Date: Feb 2003
Location: USA
Posts: 248
Default

well, good to hear, wasnt aware pelts cared about ripple and all. O well. It would be a good idea if the caps needed werent so expensive. Looking around, I have a 1500 VDC cap thats huge, and is only 4 mfd, and a 2500 VDC cap that ginormous and is only 10mfd.
hydrogen18 is offline   Reply With Quote
Unread 07-23-2003, 12:17 PM   #9
Since87
Pro/Guru - Uber Mod
 
Join Date: Sep 2002
Location: Indiana
Posts: 834
Default

It's easy to greatly reduce the ripple problem to the point where a much smaller cap can deal with it.

Just have the power company install 120V 3 Phase power. Wire the incoming 3 Phase to an outlet near your computer. Then use three bridge rectifiers.

Now you're ready to power your massive array of pelts.
Since87 is offline   Reply With Quote
Unread 07-23-2003, 01:17 PM   #10
]JR[
Cooling Neophyte
 
Join Date: Apr 2003
Location: UK
Posts: 74
Default

Or just throw the tecs away and get a giagantic 3phase hvac compressor and build a phase change 5stage cascade that runs on nitrogen Permenant ln2 temps for the same price electricity wise as your hooge tec array

And yes ripple is a killer on tecs cooling wise aswell, i was experimenting with some 10000uF caps on my homebuilt psu and with 0uF smoothing the temps were like 15degrees higher than with 50000uF worth

]JR[
]JR[ is offline   Reply With Quote
Unread 07-23-2003, 01:45 PM   #11
Brad
Thermophile
 
Brad's Avatar
 
Join Date: Oct 2001
Location: Nuu Zeeelin
Posts: 3,175
Default

I thought of this a few years ago. You'd be the only private citizen invited to every major event the electricty company had.
__________________
2x P3 1100's at 1400, Abit VP6, 2x Corsair 256mb PC150 sticks, 20gb 'cuda ATA-III, 2x 40gb 'cuda ATA-IV in raid 0. 20" Trinitron. No fans

2x 2400+ at 2288mhz (16.0 x 143), Iwill MPX2, 2x Kingmax PC-3200 256mb sticks, 4x 20gb 60gxp in Raid 5 on a Promise SX6000. Asus Ti4200 320/630. Cooled by Water
Brad is offline   Reply With Quote
Unread 07-23-2003, 02:13 PM   #12
hydrogen18
Cooling Savant
 
hydrogen18's Avatar
 
Join Date: Feb 2003
Location: USA
Posts: 248
Default

LOL!!!

i especially like "only private citizen" one!

for a 12 volt supply, what voltage rating should my caps be?
hydrogen18 is offline   Reply With Quote
Unread 07-23-2003, 03:50 PM   #13
wymjym
Cooling Neophyte
 
Join Date: Sep 2002
Location: near Austin
Posts: 96
Default

how about fuel cell technology?
wj
wymjym is offline   Reply With Quote
Unread 07-23-2003, 05:28 PM   #14
bigben2k
Responsible for 2%
of all the posts here.
 
bigben2k's Avatar
 
Join Date: May 2002
Location: Texas, U.S.A.
Posts: 8,302
Default

Quote:
Originally posted by wymjym
how about fuel cell technology?
wj
As long as it goes "VROUM!" and 0 to 60 in less than 5 seconds, OK!
bigben2k is offline   Reply With Quote
Unread 07-23-2003, 06:52 PM   #15
Alchemy
Cooling Savant
 
Join Date: Oct 2002
Location: Boston
Posts: 238
Default

Quote:
Originally posted by ]JR[
Or just throw the tecs away and get a giagantic 3phase hvac compressor and build a phase change 5stage cascade that runs on nitrogen Permenant ln2 temps for the same price electricity wise as your hooge tec array

And yes ripple is a killer on tecs cooling wise aswell, i was experimenting with some 10000uF caps on my homebuilt psu and with 0uF smoothing the temps were like 15degrees higher than with 50000uF worth

]JR[
I use a quantum-singularity watercooler in an antigravity-powered containment cell to sink all that CPU heat into a dimensional rift.

n00b.

Alchemy
Alchemy is offline   Reply With Quote
Unread 07-24-2003, 04:13 AM   #16
]JR[
Cooling Neophyte
 
Join Date: Apr 2003
Location: UK
Posts: 74
Default

Ill see if i can find a link, some guy has done it (The 5stage cascade), although its probably got a 3hr pull down time

]JR[
]JR[ is offline   Reply With Quote
Unread 07-25-2003, 10:56 AM   #17
RoboTech
Cooling Savant
 
RoboTech's Avatar
 
Join Date: Sep 2002
Location: Cincinnati, OH
Posts: 229
Default

Quote:
Originally posted by hydrogen18
for a 12 volt supply, what voltage rating should my caps be?
16 volt minimum but I would use 25 or 50 VDC myself, depending on what's available.

Quote:
Originally posted by Alchemy
I use a quantum-singularity watercooler in an antigravity-powered containment cell to sink all that CPU heat into a dimensional rift.
Kool...

What size flux-capacitors do you use to stabalize the temporal distortion fields?
RoboTech is offline   Reply With Quote
Unread 09-11-2003, 12:01 PM   #18
Cossey3
Cooling Neophyte
 
Join Date: Jun 2003
Location: South London, UK
Posts: 62
Default

assuming i could get hold of the capacitors to make this work:
in the uk we have 230vrms 50hz ac power so running 20 220w tecs on rectified and smoothed mains each would have 11.5v and draw about 19amps so in total the system would be 230v 19a
230x19= 4370 or 4.370 Kw or 4.370 units of electricty per hour so 38281.2 units per year @ 5.45p per unit. total cost £2086 per year or $3000. but for that you would have 2600w of cooilng which, if used with 2 tecs on the cpu and the rest on the water chiller, should keep the cpu well below zero. bit expensive compared to phase change though.
Cossey3 is offline   Reply With Quote
Unread 09-11-2003, 12:34 PM   #19
sevisehda
Cooling Savant
 
Join Date: May 2003
Location: NY
Posts: 234
Default

Why don't you just add a transformer to the circuit. This would cut the voltage down to whatever you wanted and isolate the system, somewhat. It would also draw far less current. 19A is alot going through 1 outlet.
sevisehda is offline   Reply With Quote
Unread 09-20-2003, 09:51 AM   #20
JFettig
Cooling Savant
 
Join Date: Feb 2003
Location: Willmar MN/Fargo ND
Posts: 504
Default

Have you ever seen those solid state lab or aquarium chillers? Bender from ocforums has a few of those and they run 10 50watt peltiers in series off 120vdc, and as far as I know, the power supply for it isnt much. Next time I see him on IRC, Ill ask him about it.

now that I think about it, My motor on my mill runs 100vdc and draws 4.5 amps. and the box is tiny that controlls everything, Ill have to take a pic of it sometime.

Jon

Last edited by JFettig; 09-20-2003 at 11:30 AM.
JFettig is offline   Reply With Quote
Unread 09-20-2003, 12:42 PM   #21
murray13
Cooling Savant
 
murray13's Avatar
 
Join Date: Sep 2002
Location: Omaha, NE USA
Posts: 216
Default

90 or 180VDC motor controllers will NOT work for powering pelts!

The motor controllers do not care about ripple, and most of them are pulse width modulation (PWM) anyway. Which will burn up a pelt fairly quickly, as has been said.

The PS inside one of the Thermotek 25x series chillers is a smps that puts out 65vdc @ 7+A. The pelt assy is made of 10 pelts in series running at about half voltage.
murray13 is offline   Reply With Quote
Unread 09-20-2003, 01:03 PM   #22
wymjym
Cooling Neophyte
 
Join Date: Sep 2002
Location: near Austin
Posts: 96
Default

I have NEVER seen a manufacturers specs sheet that indicated pwm was a bad thing for controlling peltier power, rather over the past few years I have seen recommendations from some that say they are okay as long as they are designed to work within some frequency (which I forget at the moment) range.
So, if you can post a link (from any peltier manufacturer) that would indicate that pwm is bad, I would appreciate it.
wj
wymjym is offline   Reply With Quote
Unread 09-20-2003, 01:24 PM   #23
TerraMex
Cooling Savant
 
TerraMex's Avatar
 
Join Date: Nov 2002
Location: Portugal, Europe
Posts: 870
Default

> As long as it goes "VROUM!" and 0 to 60 in less than 5 seconds, OK!

http://www.nytimes.com/2003/09/19/au...es/19ELEC.html

How about in 3.7s ? .
__________________
"we need more cowbell."
TerraMex is offline   Reply With Quote
Unread 09-20-2003, 01:30 PM   #24
superart
Cooling Savant
 
superart's Avatar
 
Join Date: Mar 2002
Location: FL
Posts: 787
Default

Quote:
Originally posted by ]JR[
Ill see if i can find a link, some guy has done it (The 5stage cascade), although its probably got a 3hr pull down time

]JR[
are you refering to this?
http://forums.procooling.com/vbb/sho...&threadid=4327
__________________
When you do things right,
people won't be sure youv'e done anything at all.

Looking to buy/trade for used Deep Fryer and Vacume Pack Sealer.
superart is offline   Reply With Quote
Unread 09-20-2003, 01:37 PM   #25
wymjym
Cooling Neophyte
 
Join Date: Sep 2002
Location: near Austin
Posts: 96
Default

and since I was already here:

TECHNICAL DESCRIPTION
Power to the thermoelectric module is delivered via a 400 Hz Pulse-Width-Modulated (PWM) output. This methodology will not reduce the thermoelectric module's reliability due to thermal cycling (as can some other on-off controllers).

http://www.tetech.com/temp/tc24-10.shtml

this is the typical information I have gathered here and there,

so once again, let's see some recommendation against pwm from the peltier manufacturers or........quit spreading the misinformation.
wj
wymjym is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 02:31 AM.


Powered by vBulletin® Version 3.7.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(C) 2005 ProCooling.com
If we in some way offend you, insult you or your people, screw your mom, beat up your dad, or poop on your porch... we're sorry... we were probably really drunk...
Oh and dont steal our content bitches! Don't give us a reason to pee in your open car window this summer...