Danner Mag 12 vs. MCP650

the jew (raven) · 02-18-2005, 12:12 PM

Ok, after going through Cathar's pump thread (again), I've arrived at a bit of a dilema. I have a Danner Magdrive 12 that I had used for an aquarium setup. Here are it's specs:

Mag Drive #12 Flow (gph) 1200 1150 1100 910 700 600 15' 110
taken from:
http://www.aquatictech.com/pumps.html

After reading a review on the MCP650, it was suggested that it would be fine for a dual CPU setup (which is what I have). So, basically, I'm wondering if a single MCP650 would be adequate in this system:

pump-->rad#1-->rad#2-->cpu#1-->cpu#2-->chipset-->gpu-->pump

Specs on hardware:

2 X dual 120mm heatercores from DD
2 X MCW6002-PX on 2 Xeon's clocked over 3gig
1 X DD i875 chipset block
1 X MCW50 on a 6800GT

Thoughts? I realize it would be ideal to have 2 MCP650's, but I don't have that kind of money right now. Thus, I'm asking if a single MCP650 would do or if I should just keep the Danner. Thanks.

nikhsub1 · 02-18-2005, 12:22 PM

Yes the 650 will be fine. The mag 12 is rediculous, horrible specs for our needs, 110W! I would bag the chipset block, but to each his own.

the jew (raven) · 02-18-2005, 12:28 PM

Yeah, I'm only putting the chipset block in the loop because I still need to fab my VRM block. I figure I'll fit the tubing so that when I finish the other block I can just switch it over.

02-18-2005, 12:12 PM	#1
the jew (raven) Cooling Neophyte Join Date: Nov 2003 Location: Where hockey pucks fly free Posts: 12	Danner Mag 12 vs. MCP650 Ok, after going through Cathar's pump thread (again), I've arrived at a bit of a dilema. I have a Danner Magdrive 12 that I had used for an aquarium setup. Here are it's specs: Mag Drive #12 Flow (gph) 1200 1150 1100 910 700 600 15' 110 taken from: http://www.aquatictech.com/pumps.html After reading a review on the MCP650, it was suggested that it would be fine for a dual CPU setup (which is what I have). So, basically, I'm wondering if a single MCP650 would be adequate in this system: pump-->rad#1-->rad#2-->cpu#1-->cpu#2-->chipset-->gpu-->pump Specs on hardware: 2 X dual 120mm heatercores from DD 2 X MCW6002-PX on 2 Xeon's clocked over 3gig 1 X DD i875 chipset block 1 X MCW50 on a 6800GT Thoughts? I realize it would be ideal to have 2 MCP650's, but I don't have that kind of money right now. Thus, I'm asking if a single MCP650 would do or if I should just keep the Danner. Thanks.

02-18-2005, 12:22 PM	#2
nikhsub1 c00ling p00n Join Date: Jun 2002 Location: L.A. Posts: 758	Yes the 650 will be fine. The mag 12 is rediculous, horrible specs for our needs, 110W! I would bag the chipset block, but to each his own. __________________ :-.,_,.-:'``':-.,_,.-:'``':-.,_,.-:'``':-.,_,.-:'``':-.,_,.-: E6700 @ 3.65Ghz / P5W DH Deluxe / 2GB 667 TeamGroup / 1900XTX PC Power & Cooling Turbo 510 Deluxe Mountain Mods U2-UFO Cube Storm G5 --> MP-01 --> PA 120.3 --> 2x DDC Ultras in Series --> Custom Clear Res "Artificial intelligence is no match for natural stupidity." 1,223,460+ Ghz Folding@Home aNonForums :-.,_,.-:'``':-.,_,.-:'``':-.,_,.-:'``':-.,_,.-:'``':-.,_,.-:

02-18-2005, 12:28 PM	#3
the jew (raven) Cooling Neophyte Join Date: Nov 2003 Location: Where hockey pucks fly free Posts: 12	Yeah, I'm only putting the chipset block in the loop because I still need to fab my VRM block. I figure I'll fit the tubing so that when I finish the other block I can just switch it over.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)