|
|
General Liquid/Water Cooling Discussion For discussion about Full Cooling System kits, or general cooling topics. Keep specific cooling items like pumps, radiators, etc... in their specific forums. |
Thread Tools |
06-30-2005, 12:05 PM | #1 |
Cooling Neophyte
Join Date: Jun 2005
Location: Québec
Posts: 7
|
CSP-Mag / multiple blocks ?
Is 1 CSP-Mag with rear inlet would be enough to pump water into this kind of loop? :shrug:
CSP-Mag-- DD TDX64 -- DD Maze4 GPU Acetal -- Bonneville HC (2x120mm) -- CSP-Mag CPU to cool is an amd64 Venice o/c @~3Ghz, the videocard is a nVidia 6600GT. I will be using a T-line , no more reservoir for me; thanks God I calculated around 3-4 feets of ½" I.D. tubing. |
06-30-2005, 01:41 PM | #2 |
Cooling Savant
Join Date: Oct 2004
Location: Canada
Posts: 260
|
Should be about 4.7-5.3 L/M with DD fittings and 1/2 ID tubing.
Is that enough flow? Well I think so, but there are many other opinions on this board *Off for the long weekend, and everyone have a good Canada Day tomorrow! |
06-30-2005, 06:59 PM | #3 |
Cooling Neophyte
Join Date: Mar 2004
Location: New Orleans
Posts: 86
|
that should be more than enough flow. there's a picture of someone w/ a loop similar to that on the forum. you're missing a reservoir or T-line in your loop.
|
06-30-2005, 07:23 PM | #4 | |
Cooling Savant
Join Date: Jan 2003
Location: Sydney, Oz
Posts: 336
|
Quote:
__________________
Long Haired Git "Securing an environment of Windows platforms from abuse - external or internal - is akin to trying to install sprinklers in a fireworks factory where smoking on the job is permitted." (Prof. Gene Spafford) My Rig, in all its glory, can be seen best here AMD XP1600 @ 1530 Mhz | Soyo Dragon + | 256 Mb PC2700 DDRAM | 2 x 40 Gb 7200rpm in Raid-0 | Maze 2, eheim 1250, dual heater cores! | Full specifications (PCDB) |
|
06-30-2005, 08:26 PM | #5 | ||
Cooling Neophyte
Join Date: Jun 2005
Location: Québec
Posts: 7
|
Quote:
Quote:
My old setup was: Hydor L30 -- DD Maze3 -- DD RadeonBlock -- DD Zchipset -- DD BayRes(the old one with no divider inside) -- Chevy 6x6 Heatercore -- L30 .... and around 9.5 feets of Clearflex60 ½" Thanks for your reply guys, I will probably set it up over the next week... Im still waiting for the GPU wb + a few questions I'm asking myself like: -Am I better to mount the heatercore with the in/out ports at the bottom or at cpu level? -Should I use PVC ½ fittings on the pump or brass ones? The brass one can be cleaned and enlarge a bit to make them more +½". My rad got the brass ones with enlarged opening -With impingements wb like the TDX, I guess I would see better performance if it's straight after the pump, followed by the Maze4GPU than pump-gpu-tdx-rad... right? -Also got the Nozzle accelerator kit with the TDX... Many reported better performance with #4 in single block application, not sure about dual blocks tho... -As for the heatercore, I still don't know if Im going to Push-pull(4fans) or pull only(2 fans). I made 2 shrouds anyway. Many told push/pull was a waste of time, tho I always got 2-3C less in push/pull on my old HCore than pulling only.... Pushing is even worst :shrug: -What's the best place to put the T-Line? Between the radiator and pump inlet, at the highest point ,after last waterblock just before the radiator? So many locations.... :shrug: Will post pics when I'll be done over the next week... too bad CanadaPost ain't delivering tomorrow Still on planning.... Last edited by JfRsQ; 06-30-2005 at 09:02 PM. |
||
07-01-2005, 07:01 AM | #6 |
Cooling Savant
Join Date: Oct 2004
Location: Canada
Posts: 260
|
PQ for blocks, no.
But I have the blocks, about 1000 MAG's and a flow meter I get 5.7 L/M with just the two blocks at 12.8V. But I don't have your rad, so I am guessing about 0.5 to 1 L/m drop. This is likely too high, and most rad's are very non-restrictive. |
07-01-2005, 10:19 AM | #7 | |
Cooling Neophyte
Join Date: Jun 2005
Location: Québec
Posts: 7
|
Quote:
1000 MAGs? Now I'm wondering why it took 5 weeks to receive one with regular CP shipping, no sign required , no tracking number, nothing :shrug: If I wouldn't be so honest, I could have complained that I never got mine and c-systems wouldn't even be able to prove that I receive it or not... Anyway, thanks for the replies Dave. I will feel more confident to use 2 blocks now with this small pump Time to go for Canada's day now, early drinking Is CSP-Mag approved to pump beer today or it would void warranty? |
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|