|
|
General Liquid/Water Cooling Discussion For discussion about Full Cooling System kits, or general cooling topics. Keep specific cooling items like pumps, radiators, etc... in their specific forums. |
Thread Tools |
10-22-2003, 08:54 AM | #1 |
Cooling Neophyte
Join Date: Aug 2003
Location: Nunavut - Canada
Posts: 35
|
damn noob!
I've been putting together my first watercooling setup, and here is what I have so far:
- Danner Mag Drive 3 Pump - Swiftech MCW462-UHT CPU Waterblock w/226W Pelt - Swiftech MCW50-T GPU Waterblock w/80W Pelt - DangerDen Z-Chip Chipset Waterblock - Black Ice Xtreme 2 Rad - 2 120mm 130CFM Delta Fans - Typhoon-Quad reservoir - 1/2" Tygon tubing - Meanwell SP-500-15 Powersupply - Dielectric Grease - Neoprene - Silicone Conformal Coating Now I'm pretty much ready to put it all together, do a leak test, then install it. But I forgot one little detail. I forgot to get fittings for the pump, I can't connect my tubing to it! Where can I get some fittings for my pump? Hopefully in Canada. |
10-22-2003, 12:21 PM | #2 |
Cooling Neophyte
Join Date: Nov 2002
Location: usa
Posts: 84
|
should be able to just go into any big hardware store like home depot, or whatever the big hardware store is up in canada and buy them.
__________________
Athlon 64 3000+ Venice / Asus A8N-SLI Premium / 2X Corsair XMS 512mb PC3200 BFG 7800GTX / Audigy 2 / Dell FP2001 20.1" / Antec TruePower 2.0 TPII-550 WD Raptor 36.7GB / WD Raptor 74GB / Maxtor 120GB SATA Water Cooled: CPU Swiftech Storm / GPU Maze 4 / Danger Den Double Heater core / Eheim 1250 |
10-22-2003, 12:24 PM | #3 |
Big PlayerMaking Big Money
Join Date: Aug 2001
Location: irc.lostgeek.com #procooling.com
Posts: 4,782
|
Home Depot or Canadian Tire or Co-op will have what you need. Just take the pump in with you. With the Danners do NOT get metal barbs and do NOT overtighten. The housing on the intake side of the pump is easy to crack.
|
10-22-2003, 01:05 PM | #4 |
Cooling Neophyte
Join Date: Aug 2003
Location: Nunavut - Canada
Posts: 35
|
Those are good suggestions, but one problem; there are no big hardware stores like Home Depot or Canadian Tire here where I live. There is a Co-op but its a small store and is mostly for groceries. Also the threads on the pump are on the inside for the intake (the fittings on my CPU waterblock fit perfectly) but the outlet end of the pump has threads on the outside. So I'd need fittings that have threads on the inside. I haven't seen any of those before. I'll give the local stores a try but I highly doubt they'll have it.
I don't suppose there is anyone who has these fittings I can buy from them incase I have no luck finding fittings locally? Last edited by FallOutBoyTonto; 10-22-2003 at 01:10 PM. |
10-22-2003, 01:11 PM | #5 |
Big PlayerMaking Big Money
Join Date: Aug 2001
Location: irc.lostgeek.com #procooling.com
Posts: 4,782
|
Yea those are female. Do you have the box? If so and you give me the thread info I could always just go pick them up and ship them to ya.
|
10-22-2003, 01:15 PM | #6 |
Cooling Neophyte
Join Date: Aug 2003
Location: Nunavut - Canada
Posts: 35
|
I do have the box, but there isn't much info on it. Just one piece of paper showing regular warnings, and performance info and features. Looks like there are no specs though. I'll try looking for the thread info, I'll post back soon.
|
10-22-2003, 01:34 PM | #7 | |
Cooling Neophyte
Join Date: Aug 2003
Location: Canada
Posts: 19
|
Quote:
Your pump requires 1/2 inch NPT Male fitting for the input, 1/2 inch NPT Female Fitting for the output (If too hard to find, I suggest that you get 1/2" NPT Union and 1/2" NPT Nipple). Best regards from Montreal Frenchnew
__________________
Sorry, gone to serve another customer. |
|
10-22-2003, 01:42 PM | #8 |
Cooling Neophyte
Join Date: Aug 2003
Location: Nunavut - Canada
Posts: 35
|
That sounds about right, the info I found (which is only a pic) also says NPT:
And according to this website the thread info for 1/2" NPT threads is: EJ Thread Size Number = 8 Thread Size In. = 1/2" Thread Type = NPT Threads per inch = 14 Pitch dia. Start of Ext. Thread = 0.75843 |
10-22-2003, 02:33 PM | #9 |
Big PlayerMaking Big Money
Join Date: Aug 2001
Location: irc.lostgeek.com #procooling.com
Posts: 4,782
|
If you don't mind 5/8" barbs (1/2" tygon goes on them fine) then I have all the parts you'd need at the house.
|
10-22-2003, 02:46 PM | #10 |
Cooling Neophyte
Join Date: Aug 2003
Location: Nunavut - Canada
Posts: 35
|
Sure, I don't mind. As long as they fit I'm happy!
|
10-23-2003, 01:39 PM | #11 |
Cooling Neophyte
Join Date: Aug 2003
Location: Nunavut - Canada
Posts: 35
|
ok, now that that is sorted out; I'm not even sure what additives to use. I've got UV reactive red dye but thats it. I kinda doubt that is going to be enough. Is there anything else I should get? :shrug:
|
10-23-2003, 04:35 PM | #12 |
Big PlayerMaking Big Money
Join Date: Aug 2001
Location: irc.lostgeek.com #procooling.com
Posts: 4,782
|
I currently run antifreeze in all my cooling loops but I have had a bit of a problem with corrosion in the past (there are pics of my poor innovatek block around here somewhere).
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|