|
|
General Liquid/Water Cooling Discussion For discussion about Full Cooling System kits, or general cooling topics. Keep specific cooling items like pumps, radiators, etc... in their specific forums. |
Thread Tools |
01-22-2002, 12:50 PM | #51 |
Cooling Savant
Join Date: Jan 2002
Location: Waukesha, Wi
Posts: 698
|
UPDATE!!! i posted some new pics to http://www.geocities.com/xdigitalchaosx/corrosion/
or just read it here and miss out on the closeup pics : I learned that the black coating is possibly a good thing, The coating blocks corrosion. However i think that this coating only forms on Aluminum.. so are additives worth while to put in a copper and brass system? also i would think that the coating may reduce the performance of aluminum.... now for the update: everything has gotten darker, The PurpleIce more than the Redline (with new info this would indicate that purple ice is better at stopping the corrosion)... the Distilled water STILL has no signs of corrosion. With the purpleice it seems that there is pitting where the bubbles stay...Now, i would figure that in a functioning system with moving water, that the bubbles would not have a chance to stick to the aluminum... So.. you know what that means... another test, this time with pumps. this may also give some info to the people wanting to know if they should leave their pumps constantly on or not! Last edited by DigitalChaos; 01-22-2002 at 02:43 PM. |
01-22-2002, 03:17 PM | #52 |
Thermophile
Join Date: Oct 2001
Location: Nuu Zeeelin
Posts: 3,175
|
the black coating may protect the Al from corrosion, but does it still transfer heat effectively? It is most likely Al2O3, or AlO, which is aluminium oxide or something like that (trying to remember from chem classes 3 years ago)
I've tried to dig up thermal conductivity values for these, but no go so far. Another thing that may be interesting to you is that it is most likely a very very thin layer of Aluminium Oxide, which isn't likely to affect temps too much at all. I know Joe is going to ream my arse for posting this link, but it does show that a thin layer of a not-very conductive metal mightn't affect temps at all. http://www.cluboverclocker.com/revie...ckel/index.htm here we see nickel is only 98W/m-k, while copper is around 400. The testing shows they perform exactly the same, which I think is due to the ultra thin layer of nickel. Now, lets assume this level of Aluminium Oxide is only a couple of microns thick. Unless it has an incredibly poor thermal conductivity, like less that 30 or something, I can't see it affecting temps too much at all. Thoughts? Comments? Abuse? |
01-22-2002, 03:29 PM | #53 |
Big PlayerMaking Big Money
Join Date: Aug 2001
Location: irc.lostgeek.com #procooling.com
Posts: 4,782
|
aluminum hydroxide is typically white tho not black, although it is hard to say what it becomes when the other chemicals are present.
|
01-22-2002, 03:31 PM | #54 |
Thermophile
Join Date: Oct 2001
Location: Nuu Zeeelin
Posts: 3,175
|
thats Al(OH)3, not Al2O3 or AlO. Although Al(OH)3 would have gone through the entire volume of water, making it all white I would have thought (precipitate)
|
01-22-2002, 03:37 PM | #55 |
Cooling Savant
Join Date: Jan 2002
Location: Waukesha, Wi
Posts: 698
|
wow.. thanks for the info guys... most of this is really starting to fit together... but i still dont like the pits from the bubbles... one more good reason to leave the pumps ON
a good way to test the thermal properties would be: get a setup with just distilled water.. and aluminum parts run it for a while till it is at its peak... then dump in the additive while its still going... and immediately record the temps for the next hour or so, this is done because the additive changes the thermal properties of water, and will give us an idea what the temps are with out the layer... then just keep the pumps on for a day... and do peak testing again... if there is a change in temps... then we know our answer |
01-22-2002, 03:48 PM | #56 |
Thermophile
Join Date: Oct 2001
Location: Nuu Zeeelin
Posts: 3,175
|
well, thats something you will have to try, let it run with distilled water for a day, record the temps, then the next day pour in some purple ice, and see what happens, if the temps suddenly go down, then level off, or if they slowly increase as the oxidation takes place, or something...
|
01-22-2002, 03:53 PM | #57 |
Cooling Savant
Join Date: Jan 2002
Location: Waukesha, Wi
Posts: 698
|
yup.... was hoping one of you guys would do it =) i dont have any aluminum stuff... hehe
|
01-22-2002, 04:06 PM | #58 |
Thermophile
Join Date: Oct 2001
Location: Nuu Zeeelin
Posts: 3,175
|
thats the problem, I don't either hehe, and I think most people don't.
|
01-22-2002, 04:17 PM | #59 |
Cooling Savant
Join Date: Jan 2002
Location: Waukesha, Wi
Posts: 698
|
yea... well maybe i will try some non aluminum testin.... (brass and copper) because this is what most have... im starting to get tired of this test after all the BS im gettin over at the [h] forum
|
01-22-2002, 04:36 PM | #60 |
Thermophile
Join Date: Oct 2001
Location: Nuu Zeeelin
Posts: 3,175
|
ehh, surely you are used to their stupidity by now?
|
01-22-2002, 04:43 PM | #61 |
Big PlayerMaking Big Money
Join Date: Aug 2001
Location: irc.lostgeek.com #procooling.com
Posts: 4,782
|
Brad even though Al2O3 (corundum) has a slightly higher thermodynamic stability, in water the typical cycle for aluminum oxide precipitation and crystallization is Al3+ (aq) -> amorphous Al(OH)3 ->crystalline Al(OH)3 (also called gibbsite). If the suspension is subjected to high temperature and pressure perhaps something else would form but that isn't a viable scenario in a jar.
|
01-22-2002, 04:52 PM | #62 |
Cooling Savant
Join Date: Jan 2002
Location: Waukesha, Wi
Posts: 698
|
hrmm.. well do you think that the slight increase in temps... and very minimal increase in pressure of a real watercooling setup would do it?
|
01-22-2002, 05:37 PM | #63 |
Thermophile
Join Date: Oct 2001
Location: Nuu Zeeelin
Posts: 3,175
|
well, he said bubbles were forming, does anyone feel like putting a seal over the top of the cup to let the bubbles build up, then put a flame into it, you should have a pop.
That means it is H2 |
01-22-2002, 05:39 PM | #64 |
Cooling Savant
Join Date: Jan 2002
Location: Waukesha, Wi
Posts: 698
|
hrmm.. that would take a lot more aluminum... i would not expect more than .5-1 cc of air comming of the 1" piece of aluminum
|
01-22-2002, 05:42 PM | #65 |
Thermophile
Join Date: Oct 2001
Location: Nuu Zeeelin
Posts: 3,175
|
cut the Al into heaps of little pieces so you have a lot more surface area, the reaction will be much more vigorous and much more will happen
|
01-22-2002, 07:13 PM | #66 |
Cooling Savant
Join Date: Jan 2002
Location: Waukesha, Wi
Posts: 698
|
ahhh yes... silly me...
i will have to try that on the weekend when i get a chance also someone suggested to me to test the ph of the mixture... the hydrogen should make it more acidic if it IS hydrogen that is being given off |
01-22-2002, 07:22 PM | #67 |
Thermophile
Join Date: Oct 2001
Location: Nuu Zeeelin
Posts: 3,175
|
yeah, that'd be an idea too, I'd have thought it'd be going alkali, cause the H2 is escaping, so there is more OH.
|
01-22-2002, 07:50 PM | #68 |
Cooling Savant
Join Date: Jan 2002
Location: Waukesha, Wi
Posts: 698
|
the oxygen would be goin to the surface of the aluminum to cause the oxidation... they hydrogen would be the by product
i was thinking that some of the hydrogen would go into the water, and some would form bubbles man... this has turned into something requiring WAY more time than i have... i thought it was gonna be as easy as just takin pics ever so often... and just seeing what one corrodes first |
01-22-2002, 07:58 PM | #69 |
Thermophile
Join Date: May 2001
Location: UK
Posts: 1,064
|
H2? I thought Hydrogen was stable as a single atom which would make it H.
__________________
Once upon a time, in a land far far away... |
01-22-2002, 08:58 PM | #70 |
Thermophile
Join Date: Oct 2001
Location: Nuu Zeeelin
Posts: 3,175
|
H2 is when it is a gas, which is the only way it exists stably. It can be just H in things like NaOH
|
01-22-2002, 09:21 PM | #71 |
Thermophile
Join Date: May 2001
Location: UK
Posts: 1,064
|
Yes, hmm I thought Hydrogen could float around in a single attom, not pairs, guess not
__________________
Once upon a time, in a land far far away... |
01-22-2002, 09:27 PM | #72 |
Cooling Savant
Join Date: Jan 2002
Location: Waukesha, Wi
Posts: 698
|
chemistry sucks... tell it to leave my damn cooling system alone
|
01-22-2002, 09:35 PM | #73 |
Cooling Savant
Join Date: Jul 2001
Location: Kingston, Jamaica
Posts: 204
|
Yup Hydrogen is only found as H2 when unreacted with other elements. If the solution is acidic it's because of exess H+ ions (H2 is insoluble in water and so isn't acidic or basic), the solution will become less acidic with time as H+ is taken out of solution. Also acid/metal rections always form hydroxides not oxides, so if this was acid then you would have aluminium hydroxide forming and promptly disolving, not a protective coating of aluminium oxide. Also aluminium is so reactive that this corundum coating (this is the same stuff as saphire and high quality watch glass) forms within hours of Als exposure to air. Anodizing is just creating a thick coating.
Edward |
01-22-2002, 09:37 PM | #74 |
The Pro/Life Support System
Join Date: Dec 1999
Location: Denver, CO
Posts: 4,041
|
I think I learned more about chemistry in this thread than all my schooling.
hehe :shrug:
__________________
Joe - I only take this hat off for one thing... ProCooling archive curator and dusty skeleton. |
01-22-2002, 09:38 PM | #75 |
Cooling Savant
Join Date: Jan 2002
Location: Waukesha, Wi
Posts: 698
|
awsome... so how do you anodized copper? like... how would i find the stuff i need?
you cant anodize copper can you? |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|