|
|
Heatsink/ Heat Pipe / ThermoSiphon Cooling The cat will only make the mistake of putting its paw by your HSF once. :) Also the place to discuss the new high end heat pipe goodness. |
Thread Tools |
09-24-2002, 08:11 PM | #1 |
Cooling Neophyte
Join Date: Nov 2001
Location: new jersey
Posts: 82
|
Best fans for case cooling ?
i need some opinions on which case fans are the best to use ..
im gonna have a baybus .. so i can run them at 12 or 7 volt .. thanks |
09-24-2002, 08:29 PM | #2 |
Cooling Savant
Join Date: Aug 2002
Location: Canada, Montreal
Posts: 136
|
Im a big panaflo fan *grin*
Seriously though, panaflos are great, and produce the most cfm for the noise level. Cant go wrong with them. Next in line would be the YS Tecks and Sunons |
09-24-2002, 11:06 PM | #3 |
Cooling Neophyte
Join Date: Nov 2001
Location: new jersey
Posts: 82
|
well i just found about 8 or so high flo panaflos .. 80mm
so im gonna run them .. 39.6 cfm can i run them at 7 volt ?? cuz i know some 80mm i tried running at 7 volt just stopped |
09-24-2002, 11:15 PM | #4 |
Cooling Savant
Join Date: Mar 2002
Location: Silver Spring, MD
Posts: 282
|
172mm Comair Rotron. 12v 235cfm, 55dba. Run it at 7v and u still get a nice breeze and very low pitched noise. I personally did the trick with the ground attached to 5volt line. Much easier and faster to do. Not permanent (i did over a connection between the fan and the psu). And doesnt generate heat.
__________________
-sonix- ======================= Antec SX830 Abit KR7A-133 MSI Geforce3 Ti200 VT128 TV-IN and TV-OUT Sound Blaster Audigy Linksys LNE100 V2.0 Toshiba DVD Drive 40x/16x IBM Deskstar 60GXP 60gig Watercooled http://www.sonixnet.tk ======================= |
09-25-2002, 02:12 AM | #5 |
Thermophile
Join Date: Oct 2001
Location: Nuu Zeeelin
Posts: 3,175
|
I quite like the thermal take case fan II's. You can offset their speed by using the little resistor, and still keep them variable by using the temp sensor. You have a *massive* cfm and noise range as well.
for pure quality papst > panaflo > sanyo denki > nidec > delta
__________________
2x P3 1100's at 1400, Abit VP6, 2x Corsair 256mb PC150 sticks, 20gb 'cuda ATA-III, 2x 40gb 'cuda ATA-IV in raid 0. 20" Trinitron. No fans 2x 2400+ at 2288mhz (16.0 x 143), Iwill MPX2, 2x Kingmax PC-3200 256mb sticks, 4x 20gb 60gxp in Raid 5 on a Promise SX6000. Asus Ti4200 320/630. Cooled by Water |
09-25-2002, 01:04 PM | #6 |
Cooling Savant
Join Date: Oct 2000
Location: Rockledge,FL,US
Posts: 731
|
I like my Panaflos.
got a M1A(model above the popular L1A).
__________________
My old and retired watercooling setup. Watercooled K6-2 450 at 600 Also Retired - Watercooling an XP1800@1782MHz |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|