|
|
Water Block Design / Construction Building your own block? Need info on designing one? Heres where to do it |
Thread Tools |
11-02-2006, 08:44 AM | #1 |
Cooling Neophyte
Join Date: Dec 2005
Location: Sweden
Posts: 38
|
Help on DIY VGA block..
Hello.
I dont know if this is to much to ask for but if there is anybody that can help me on doing a waterblock for my MSI NX6600GT card.. I dont know distance to mounting holes and such, dont know if I should go with a full cover block or just for the GPU.. And it cant be to thick either due I got a Shuttle so it can only be about 23-24mm thick.. Hope you guys can help me out a little bit.. Best regards, JAxen.. |
11-02-2006, 09:22 AM | #2 | |
Cooling Savant
Join Date: Jun 2005
Location: Skokie, Illinois
Posts: 322
|
Re: Help on DIY VGA block..
Quote:
__________________
My new rig.... Intel SE440BX-3, PIII 550 (@ 680) MX440 275/332 (@ 350/400) and 3DFX Voodo 5 5500 160/160 (@180/180) Two Opticals and 120 gigs (w/28gigs in RAID0) on 4 Maxstors |
|
11-02-2006, 09:35 AM | #3 |
Cooling Neophyte
Join Date: Dec 2005
Location: Sweden
Posts: 38
|
Re: Help on DIY VGA block..
Mad bad..
I want to make it myself and I was hoping that I could get some help over here.. |
11-03-2006, 11:50 AM | #4 |
Pro/Staff
Join Date: Oct 2001
Location: Klamath Falls, OR
Posts: 1,439
|
Re: Help on DIY VGA block..
Why not use a bit of styrofoam as a template? Place foam where block should go, and punch through the mounting holes from the backside. You will end up with a piece of styrofoam that can show you exactly where the holes should be.
|
11-03-2006, 04:50 PM | #5 |
Cooling Neophyte
Join Date: Mar 2003
Location: Canada
Posts: 32
|
Re: Help on DIY VGA block..
These dimensions are taken from an eVGA 6600GT
Measured by caliper. Hole diameter is 2.5mm |
11-18-2006, 09:52 AM | #6 |
Cooling Neophyte
Join Date: Dec 2005
Location: Sweden
Posts: 38
|
Re: Help on DIY VGA block..
Well, it shows out that I cant mill this kinds of thing anymore :[
So if anyone of you know where I can get a waterblock for my MSI NX6600GT I'd appriciate a hotlink to that place |
11-18-2006, 11:57 AM | #7 | |
Put up or Shut Up
Join Date: Dec 2001
Location: Spokane WA
Posts: 6,506
|
Re: Help on DIY VGA block..
Quote:
20mm thick it says? |
|
11-18-2006, 05:03 PM | #8 |
Cooling Savant
Join Date: Jul 2005
Location: california
Posts: 429
|
Re: Help on DIY VGA block..
http://www.petrastechshop.com/sicyfugpuwa.html
silver prop 19mm height http://www.petrastechshop.com/q.html 25.2mm is too big but you can trim 1mm off the acetal |
11-18-2006, 06:59 PM | #9 |
Cooling Neophyte
Join Date: Dec 2005
Location: Sweden
Posts: 38
|
Re: Help on DIY VGA block..
Thanks a ton guys..
About Danger Den maze 4 block, I didnt see that it would fit an 6600.. Does it fit anyway? |
11-18-2006, 07:20 PM | #10 |
Put up or Shut Up
Join Date: Dec 2001
Location: Spokane WA
Posts: 6,506
|
Re: Help on DIY VGA block..
Probably fit but I think it is thicker than 24mm. Maybe not...
|
11-18-2006, 07:56 PM | #11 |
Cooling Neophyte
Join Date: Dec 2005
Location: Sweden
Posts: 38
|
Re: Help on DIY VGA block..
Yeah but that is no problem if its about 1mm too thick.. Aslong as the mounting holes fit..
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|