What do I need to make a Danner 500gph Pondmaster work with 1/2"id tubing? - Page 2

Demonfire · 06-04-2004, 12:57 PM

Quote:

Originally Posted by pHaestus

no no

I mean put the hose clamp on the outside of the mag5's inlet piece itself (on the pump housing)

Oh, you mean put it there to stableize the housing?

pHaestus · 06-04-2004, 01:34 PM

yes exactly. Not an issue if the inlet is connected directly of via a short straight tube to the res though (as TheXtremeDude has done).

Demonfire · 06-05-2004, 11:17 AM

Btw, how exactly do you "prime" a pump when using a res?

(also, what would be a good 1/2id res to use?)

pHaestus · 06-05-2004, 11:23 AM

You fill the res with water and then turn the pump on when water's above the inlet

Demonfire · 06-05-2004, 11:25 AM

Quote:

Originally Posted by pHaestus

You fill the res with water and then turn the pump on when water's above the inlet

Ok, so the water will just spontainiously flow through the tubing and into and through teh pump?

TheXtremeDude · 06-05-2004, 01:45 PM

I wouldn't say it was spontaneous. The flow is caused by the pumps compression. Without the pump the water would not flow or circulate through the system. But I will leave that to the lone thermodynamics major who hangs out here to expound upon. LOL

Demonfire · 06-05-2004, 03:53 PM

Quote:

Originally Posted by TheXtremeDude

I wouldn't say it was spontaneous. The flow is caused by the pumps compression. Without the pump the water would not flow or circulate through the system. But I will leave that to the lone thermodynamics major who hangs out here to expound upon. LOL

No, i mean when filling teh system, water has to flow through teh pump before it can run (unless its self priming).

TheXtremeDude · 06-05-2004, 04:46 PM

Oh I see. Yes, it is a centrifugal pump and cannot pull water from a lower level when run inline. In order to start it must be below water level and "primed" or filled with water. Unless air can escape from the outlet, the pump will not start. When setup correctly the air bleeds out very quickly. I guess you would call it self priming. You fill the res and start the pump and the air bleeds out. I hope that is what you were looking for.

Demonfire · 06-06-2004, 08:31 PM

Quote:

Originally Posted by TheXtremeDude

Oh I see. Yes, it is a centrifugal pump and cannot pull water from a lower level when run inline. In order to start it must be below water level and "primed" or filled with water. Unless air can escape from the outlet, the pump will not start. When setup correctly the air bleeds out very quickly. I guess you would call it self priming. You fill the res and start the pump and the air bleeds out. I hope that is what you were looking for.

Exactly

Demonfire · 06-09-2004, 12:33 PM

Also, should I follow what is in the magdrive guide:

http://www.procooling.com/articles/h...___3_31_00.php

TheXtremeDude · 06-09-2004, 01:46 PM

Quote:

Originally Posted by Demonfire

Also, should I follow what is in the magdrive guide:

http://www.procooling.com/articles/h...___3_31_00.php

I have not had any problems with leaks, but if you find that you do, that seems like a good solution or fix. I wouldn't do it unless it became needed. Is this supposed to be a common problem with this pump and I have just been lucky? :shrug:

06-04-2004, 01:34 PM	#27
pHaestus Big Player Making Big Money Join Date: Aug 2001 Location: irc.lostgeek.com #procooling.com Posts: 4,782	yes exactly. Not an issue if the inlet is connected directly of via a short straight tube to the res though (as TheXtremeDude has done). __________________ Getting paid like a biker with the best crank... -MF DOOM

06-05-2004, 11:23 AM	#29
pHaestus Big Player Making Big Money Join Date: Aug 2001 Location: irc.lostgeek.com #procooling.com Posts: 4,782	You fill the res with water and then turn the pump on when water's above the inlet __________________ Getting paid like a biker with the best crank... -MF DOOM

06-05-2004, 11:17 AM	#28
Demonfire Cooling Neophyte Join Date: Apr 2004 Location: Yorktown, New York Posts: 40	Btw, how exactly do you "prime" a pump when using a res? (also, what would be a good 1/2id res to use?)

06-05-2004, 01:45 PM	#31
TheXtremeDude Cooling Neophyte Join Date: May 2004 Location: USA Posts: 13	I wouldn't say it was spontaneous. The flow is caused by the pumps compression. Without the pump the water would not flow or circulate through the system. But I will leave that to the lone thermodynamics major who hangs out here to expound upon. LOL

06-05-2004, 04:46 PM	#33
TheXtremeDude Cooling Neophyte Join Date: May 2004 Location: USA Posts: 13	Oh I see. Yes, it is a centrifugal pump and cannot pull water from a lower level when run inline. In order to start it must be below water level and "primed" or filled with water. Unless air can escape from the outlet, the pump will not start. When setup correctly the air bleeds out very quickly. I guess you would call it self priming. You fill the res and start the pump and the air bleeds out. I hope that is what you were looking for.

06-09-2004, 12:33 PM	#35
Demonfire Cooling Neophyte Join Date: Apr 2004 Location: Yorktown, New York Posts: 40	Also, should I follow what is in the magdrive guide: http://www.procooling.com/articles/h...___3_31_00.php

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)