Tbred XP1800 vcore-mod?

SuperflyDK · 12-16-2002, 05:39 AM

Hi all!

I just received my brand new T-bred-A XP1800, and i really want to give this baby a high vcore.

Is it possible to go pass the +0.1 volt increase, if my motherboard doesnt support this? (Soltek SL-75DRV5).

Is there any wiremod og bridgepainting i could look into, to increase the vcore further?

I have no idea how it clocks yet, but if you want, i could keep you up to date later today (still at work).

hara · 12-16-2002, 06:09 AM

some of the bridges on the cpu control the default voltage

bigben2k · 12-16-2002, 11:54 AM

You need a voltmod.

Try this forum . If it's not there, make a thread, someone will probably answer you.

pHaestus · 12-16-2002, 12:46 PM

The vast majority of amd mobos use the HIP6301 voltage regulator, which is easy to volt mod (well if you can solder). Look around at the ICs on the mobo and see if you spot HIP 6301 near the CPU socket or the mosfets.

Brad · 12-17-2002, 02:03 AM

if you hate soldering you can just connect up some of the bridges on the cpu itself

http://www.beachlink.com/candjac/TbredDecode0.htm

this page has it all (yes I do have that page bookmarked, yes I do have over 1000 bookmarks

)

SuperflyDK · 12-17-2002, 02:27 AM

Well, i guess i was lucky, cuz allthough the CPU is running at default 1.5 volt, i can still crank it up to 1.85 volts, which would be the same as giving a Palomino 2.1 volt.

I havent had the time to really test the CPU yet, but right now it's running at 1817Mhz @ 1.65 volt. As soon as i get off work today, i'll give it 1.85, and try to reach 1900Mhz.

I guess a XP1600 AGOIA would be a better clocker, but this new tbred XP1800 is actually surprisingly cool. It runs 2 degrees celcius cooler than my old XP1800 Palomino, at a room temperature thats 1 degree warmer.

12-16-2002, 05:39 AM	#1
SuperflyDK Cooling Neophyte Join Date: Dec 2002 Location: Denmark Posts: 2	Tbred XP1800 vcore-mod? Hi all! I just received my brand new T-bred-A XP1800, and i really want to give this baby a high vcore. Is it possible to go pass the +0.1 volt increase, if my motherboard doesnt support this? (Soltek SL-75DRV5). Is there any wiremod og bridgepainting i could look into, to increase the vcore further? I have no idea how it clocks yet, but if you want, i could keep you up to date later today (still at work). __________________ Regards, SuperflyDK

12-16-2002, 11:54 AM	#3
bigben2k Responsible for 2% of all the posts here. Join Date: May 2002 Location: Texas, U.S.A. Posts: 8,302	You need a voltmod. Try this forum . If it's not there, make a thread, someone will probably answer you. __________________ WBTA (Water Block Testing Alliance) Nordic Hardware WC 101

12-17-2002, 02:03 AM	#5
Brad Thermophile Join Date: Oct 2001 Location: Nuu Zeeelin Posts: 3,175	if you hate soldering you can just connect up some of the bridges on the cpu itself http://www.beachlink.com/candjac/TbredDecode0.htm this page has it all (yes I do have that page bookmarked, yes I do have over 1000 bookmarks ) __________________ 2x P3 1100's at 1400, Abit VP6, 2x Corsair 256mb PC150 sticks, 20gb 'cuda ATA-III, 2x 40gb 'cuda ATA-IV in raid 0. 20" Trinitron. No fans 2x 2400+ at 2288mhz (16.0 x 143), Iwill MPX2, 2x Kingmax PC-3200 256mb sticks, 4x 20gb 60gxp in Raid 5 on a Promise SX6000. Asus Ti4200 320/630. Cooled by Water

12-17-2002, 02:27 AM	#6
SuperflyDK Cooling Neophyte Join Date: Dec 2002 Location: Denmark Posts: 2	:) Well, i guess i was lucky, cuz allthough the CPU is running at default 1.5 volt, i can still crank it up to 1.85 volts, which would be the same as giving a Palomino 2.1 volt. I havent had the time to really test the CPU yet, but right now it's running at 1817Mhz @ 1.65 volt. As soon as i get off work today, i'll give it 1.85, and try to reach 1900Mhz. I guess a XP1600 AGOIA would be a better clocker, but this new tbred XP1800 is actually surprisingly cool. It runs 2 degrees celcius cooler than my old XP1800 Palomino, at a room temperature thats 1 degree warmer. __________________ Regards, SuperflyDK

12-16-2002, 06:09 AM	#2
hara Cooling Savant Join Date: Oct 2002 Location: Malta, Mediterranean Posts: 662	some of the bridges on the cpu control the default voltage

12-16-2002, 12:46 PM	#4
pHaestus Big Player Making Big Money Join Date: Aug 2001 Location: irc.lostgeek.com #procooling.com Posts: 4,782	The vast majority of amd mobos use the HIP6301 voltage regulator, which is easy to volt mod (well if you can solder). Look around at the ICs on the mobo and see if you spot HIP 6301 near the CPU socket or the mosfets.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)