2400 and chilled water

wymjym · 12-09-2002, 04:59 PM

some quick observations are here
wj

bigben2k · 12-09-2002, 05:07 PM

What FSB are you running?

wymjym · 12-09-2002, 05:30 PM

right now?
12.5 x 188 = 2350

initially I played with the 15x multi but 15 x 157 'felt' quite a bit slower. If it can operate at 15 x 166 at a lower V after some 'cooking' on my part I'll run it there. BTW the max V I tried was 2.19...I started to get nervous and just quit. I can crank it up to an indicated 2.3but have no desire to go there.
the 2550 was 15 x 170

wj

bigben2k · 12-09-2002, 06:08 PM

I agree. From everything I've seen, running above 1.85 seems to be "asking for it". Mem volt at 2.8 or 2.9, but not higher seems to be in order.

Hixup · 12-09-2002, 07:08 PM

you should get a dremel and unlock the multiplier. Be daring with that dremel.

wymjym · 12-10-2002, 09:21 AM

Quote:

Originally posted by Hixup
you should get a dremel and unlock the multiplier. Be daring with that dremel.

???????????????????
wj

MadDogMe · 12-10-2002, 10:10 AM

Nah use a front door key, only thing to unlock a 6entuim is a frontdoor key, you'll prolly need the 9remel to get it of the key ring though

...

Hixup · 12-11-2002, 06:22 PM

to unlock the multiplier ratio on amd xp 2100+ (i think) you need a dremel and to be daring by fooling the computer into thinking its a 1600+, that will unlock it.
Heres a link http://www.pcstats.com/articleview.c...id=1009&page=2

airspirit · 12-11-2002, 07:03 PM

He's using a 2400+, meaning he only has to link the last L3 bridge. Dremeling is bad. Very bad.

MadDogMe · 12-12-2002, 04:32 AM

They were using an Engraver set at the lowest setting as well, not a Dremel!...
If I was to do that I'd use either a scalpal blade(very gently!!) or some high graded 1200+ wen&dry folded over into a 'sharp edge' and gently(!!) sand the trace away. the trouble is there are traces under the surface as well. when joining the bridges to 'unlock' an XP you have to be careful not to sand away to much of the green laminate surface, if you do there is a copper trace underneath that if the 'electrical conduct paint' touches it outside of the bridges 'oval' shaped enclosure) it locks the multiplyer at 11x (I think it's 11 anyway)...

wymjym · 12-12-2002, 02:51 PM

airspirit was correct,
it is a 2400 and all I had to do was jump the one bridge. I painted it but my buddy did the wire trick.
pretty easy.
wj

12-09-2002, 04:59 PM	#1
wymjym Cooling Neophyte Join Date: Sep 2002 Location: near Austin Posts: 96	2400 and chilled water some quick observations are here wj

12-09-2002, 05:07 PM	#2
bigben2k Responsible for 2% of all the posts here. Join Date: May 2002 Location: Texas, U.S.A. Posts: 8,302	What FSB are you running? __________________ WBTA (Water Block Testing Alliance) Nordic Hardware WC 101

12-09-2002, 06:08 PM	#4
bigben2k Responsible for 2% of all the posts here. Join Date: May 2002 Location: Texas, U.S.A. Posts: 8,302	I agree. From everything I've seen, running above 1.85 seems to be "asking for it". Mem volt at 2.8 or 2.9, but not higher seems to be in order. __________________ WBTA (Water Block Testing Alliance) Nordic Hardware WC 101

12-09-2002, 07:08 PM	#5
Hixup Cooling Neophyte Join Date: Jun 2002 Location: By the computer Posts: 51	you should get a dremel and unlock the multiplier. Be daring with that dremel. __________________ AMD Athlon XP 1900+ Water Cooled Soyo SY-K7V Dragon plus! 512 DDR radoen 9500 Soft Mod Give Me Money

12-11-2002, 06:22 PM	#8
Hixup Cooling Neophyte Join Date: Jun 2002 Location: By the computer Posts: 51	to unlock the multiplier ratio on amd xp 2100+ (i think) you need a dremel and to be daring by fooling the computer into thinking its a 1600+, that will unlock it. Heres a link http://www.pcstats.com/articleview.c...id=1009&page=2 __________________ AMD Athlon XP 1900+ Water Cooled Soyo SY-K7V Dragon plus! 512 DDR radoen 9500 Soft Mod Give Me Money

12-09-2002, 05:30 PM	#3
wymjym Cooling Neophyte Join Date: Sep 2002 Location: near Austin Posts: 96	right now? 12.5 x 188 = 2350 initially I played with the 15x multi but 15 x 157 'felt' quite a bit slower. If it can operate at 15 x 166 at a lower V after some 'cooking' on my part I'll run it there. BTW the max V I tried was 2.19...I started to get nervous and just quit. I can crank it up to an indicated 2.3but have no desire to go there. the 2550 was 15 x 170 wj

12-10-2002, 10:10 AM	#7
MadDogMe Thermophile Join Date: Aug 2002 Location: Just shut up ;) ... Posts: 1,068	Nah use a front door key, only thing to unlock a 6entuim is a frontdoor key, you'll prolly need the 9remel to get it of the key ring though ...

12-11-2002, 07:03 PM	#9
airspirit Been /.'d... have you? Join Date: Jul 2002 Location: Moscow, ID Posts: 1,986	He's using a 2400+, meaning he only has to link the last L3 bridge. Dremeling is bad. Very bad. __________________ #!/bin/sh {who;} {last;} {pause;} {grep;} {touch;} {unzip;} mount /dev/girl -t {wet;} {fsck;} {fsck;} {fsck;} {fsck;} echo yes yes yes {yes;} umount {/dev/girl;zip;} rm -rf {wet.spot;} {sleep;} finger: permission denied

12-12-2002, 04:32 AM	#10
MadDogMe Thermophile Join Date: Aug 2002 Location: Just shut up ;) ... Posts: 1,068	They were using an Engraver set at the lowest setting as well, not a Dremel!... If I was to do that I'd use either a scalpal blade(very gently!!) or some high graded 1200+ wen&dry folded over into a 'sharp edge' and gently(!!) sand the trace away. the trouble is there are traces under the surface as well. when joining the bridges to 'unlock' an XP you have to be careful not to sand away to much of the green laminate surface, if you do there is a copper trace underneath that if the 'electrical conduct paint' touches it outside of the bridges 'oval' shaped enclosure) it locks the multiplyer at 11x (I think it's 11 anyway)... Last edited by MadDogMe; 12-12-2002 at 04:38 AM.

12-12-2002, 02:51 PM	#11
wymjym Cooling Neophyte Join Date: Sep 2002 Location: near Austin Posts: 96	airspirit was correct, it is a 2400 and all I had to do was jump the one bridge. I painted it but my buddy did the wire trick. pretty easy. wj

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)