atx 20 and 24 connector....

kai · 12-28-2002, 04:39 PM

Im making an adapter for my 24 pin psu , and im looking for the pin outs its a fortron 460w FSP460-60pfn
I found some atx 20 but they seemed be wronge , i cant find the 24 pin . If anyone could help thanks.

kai · 12-28-2002, 05:44 PM

ok i found the pinouts i have two concerns.

On a 20 pin atx pin 18 is white and is listed as -5v or 12stl
there is no -5v for atx-ges 24 pin
and on pin 8 is orange and is listed as power_ok or fal#

what are these for are they needed? can i just not connect those?

kai · 12-28-2002, 06:15 PM

ok i found power good grey on plug 2 i tried it with power on green and it started up the psu.

so im guessing power good is the same as power ok so im going to put it on pin 8.

kai · 12-29-2002, 12:38 PM

tested it and works , though i dont have a -5v is it needed?

Brad · 01-01-2003, 04:26 AM

is your psu atxges, eps12v or wtx? each has differant pinouts.

www.pcpowerandcooling has all the correct pinouts, google does too

You'll find all of the colours will mean the same things between all the differant standards, if that helps you at all

kai · 01-01-2003, 01:20 PM

the fortron 460watt is atxges im trying to adapt a 20 pin to it , i have all the wires connected and stuff , except the white which is -5V and i cant find -5V on the fortron do i need this? what is it for?

i found that the 3.3v rail was a different color.

Brad · 01-01-2003, 04:06 PM

I'd just leave it completely disconnected, as I said in that other thread.

Apart from that have you got all the info you need?

12-28-2002, 04:39 PM	#1
kai Cooling Neophyte Join Date: Aug 2002 Location: blah Posts: 35	atx 20 and 24 connector.... Im making an adapter for my 24 pin psu , and im looking for the pin outs its a fortron 460w FSP460-60pfn I found some atx 20 but they seemed be wronge , i cant find the 24 pin . If anyone could help thanks.

01-01-2003, 04:26 AM	#5
Brad Thermophile Join Date: Oct 2001 Location: Nuu Zeeelin Posts: 3,175	is your psu atxges, eps12v or wtx? each has differant pinouts. www.pcpowerandcooling has all the correct pinouts, google does too You'll find all of the colours will mean the same things between all the differant standards, if that helps you at all __________________ 2x P3 1100's at 1400, Abit VP6, 2x Corsair 256mb PC150 sticks, 20gb 'cuda ATA-III, 2x 40gb 'cuda ATA-IV in raid 0. 20" Trinitron. No fans 2x 2400+ at 2288mhz (16.0 x 143), Iwill MPX2, 2x Kingmax PC-3200 256mb sticks, 4x 20gb 60gxp in Raid 5 on a Promise SX6000. Asus Ti4200 320/630. Cooled by Water

01-01-2003, 04:06 PM	#7
Brad Thermophile Join Date: Oct 2001 Location: Nuu Zeeelin Posts: 3,175	I'd just leave it completely disconnected, as I said in that other thread. Apart from that have you got all the info you need? __________________ 2x P3 1100's at 1400, Abit VP6, 2x Corsair 256mb PC150 sticks, 20gb 'cuda ATA-III, 2x 40gb 'cuda ATA-IV in raid 0. 20" Trinitron. No fans 2x 2400+ at 2288mhz (16.0 x 143), Iwill MPX2, 2x Kingmax PC-3200 256mb sticks, 4x 20gb 60gxp in Raid 5 on a Promise SX6000. Asus Ti4200 320/630. Cooled by Water

12-28-2002, 05:44 PM	#2
kai Cooling Neophyte Join Date: Aug 2002 Location: blah Posts: 35	ok i found the pinouts i have two concerns. On a 20 pin atx pin 18 is white and is listed as -5v or 12stl there is no -5v for atx-ges 24 pin and on pin 8 is orange and is listed as power_ok or fal# what are these for are they needed? can i just not connect those?

12-28-2002, 06:15 PM	#3
kai Cooling Neophyte Join Date: Aug 2002 Location: blah Posts: 35	ok i found power good grey on plug 2 i tried it with power on green and it started up the psu. so im guessing power good is the same as power ok so im going to put it on pin 8.

12-29-2002, 12:38 PM	#4
kai Cooling Neophyte Join Date: Aug 2002 Location: blah Posts: 35	tested it and works , though i dont have a -5v is it needed?

01-01-2003, 01:20 PM	#6
kai Cooling Neophyte Join Date: Aug 2002 Location: blah Posts: 35	the fortron 460watt is atxges im trying to adapt a 20 pin to it , i have all the wires connected and stuff , except the white which is -5V and i cant find -5V on the fortron do i need this? what is it for? i found that the 3.3v rail was a different color.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)