Go Back   Pro/Forums > ProCooling Technical Discussions > General Liquid/Water Cooling Discussion > Water Block Design / Construction
Password
Register FAQ Members List Calendar JavaChat Mark Forums Read

Water Block Design / Construction Building your own block? Need info on designing one? Heres where to do it

Reply
Thread Tools
Unread 11-24-2002, 02:23 PM   #1
Puzzdre
Cooling Savant
 
Puzzdre's Avatar
 
Join Date: Aug 2002
Location: Croatia
Posts: 969
Default Another #Rotor style block...

here:
Attached Images
File Type: jpg myfirst.jpg (8.2 KB, 422 views)
__________________
'Out of cheese error...
...please reboot the universe (press the GBL to continue)'
Puzzdre is offline   Reply With Quote
Unread 11-24-2002, 02:25 PM   #2
Puzzdre
Cooling Savant
 
Puzzdre's Avatar
 
Join Date: Aug 2002
Location: Croatia
Posts: 969
Default

Just kidding...

That's my old, first timer block...

Here's the new one:
Attached Images
File Type: jpg finish4.jpg (10.7 KB, 411 views)
__________________
'Out of cheese error...
...please reboot the universe (press the GBL to continue)'
Puzzdre is offline   Reply With Quote
Unread 11-24-2002, 02:26 PM   #3
Puzzdre
Cooling Savant
 
Puzzdre's Avatar
 
Join Date: Aug 2002
Location: Croatia
Posts: 969
Default

here's another view:
__________________
'Out of cheese error...
...please reboot the universe (press the GBL to continue)'
Puzzdre is offline   Reply With Quote
Unread 11-24-2002, 02:27 PM   #4
Puzzdre
Cooling Savant
 
Puzzdre's Avatar
 
Join Date: Aug 2002
Location: Croatia
Posts: 969
Default

hands faster than mind...(not such a problem though...:shrug: )
Attached Images
File Type: jpg finish1.jpg (28.5 KB, 429 views)
__________________
'Out of cheese error...
...please reboot the universe (press the GBL to continue)'
Puzzdre is offline   Reply With Quote
Unread 11-24-2002, 02:33 PM   #5
Puzzdre
Cooling Savant
 
Puzzdre's Avatar
 
Join Date: Aug 2002
Location: Croatia
Posts: 969
Default

And here are my temps: Idle 36, full load 39, room 25 deg Celsius.

What puzzles me is, with that old block (z style, 6 mm dia channels), I was getting idle 34, full load 39 - 40. It was restrictive, the new block flows muuuch better, but the temps are pointing to problem. I posted this in another thread, to explain things a little...
"So, found one crappy Y garden hose piece, re-drilled it to 10 mm ID. Changed crappy inlet barb on my rad from 8 mm ID to 10 mm ID (best I could do today afternoon). Problem is that Y piece is too wide so my 12 mm ID PVC tubes kinked a lot, so I replaced them with 8 mm ID silicone (only ones I got). Till later this evening I was pissed off enough with my small case and that Y piece, so I didn't have the nerve to take out and redrill another Y also in system, using it like a fill point/air trap. So that's another restriction (that Y is 8 mm ID).
The good thing is that my flow indicator spins like mad, which wasn't the case with my old block.
Now I'm idling on 36, with old block was 34. Full load with the new block is 39, with old block was 39 - 40 deg. Room temp are pretty steady these days, 25 deg. Two 120 mm Adda fans at 7 V."

The rad is Lancia prisma hcore, big enough for those two fans...

I also reinstalled block four times, with springs, without them...

Dunno...

Help?

/edit/ that 8 mm ID silicone tubes go from two outlets to the Y piece, about 12 cm in length (2 x 12 cm). All other tubing is 12 mm ID...

2nd/edit/ pump is Maxijet 1000, AMD XP 1800+ @ 1667 Mhz...
__________________
'Out of cheese error...
...please reboot the universe (press the GBL to continue)'

Last edited by Puzzdre; 11-24-2002 at 02:41 PM.
Puzzdre is offline   Reply With Quote
Unread 11-24-2002, 02:59 PM   #6
LiquidRulez
Cooling Savant
 
LiquidRulez's Avatar
 
Join Date: Sep 2002
Location: In Hell
Posts: 322
Default

Man I tell ya.........you've got some serious patience to sit and drill all of those holes in that thing.
How long did it take you??
LiquidRulez is offline   Reply With Quote
Unread 11-24-2002, 03:13 PM   #7
Puzzdre
Cooling Savant
 
Puzzdre's Avatar
 
Join Date: Aug 2002
Location: Croatia
Posts: 969

Thx man,

It didn't take too long, maybe an hour or so, just for drilling the small ones...
__________________
'Out of cheese error...
...please reboot the universe (press the GBL to continue)'
Puzzdre is offline   Reply With Quote
Unread 11-24-2002, 03:36 PM   #8
Arcturius
Cooling Savant
 
Join Date: Aug 2001
Location: Chippewa Falls, Wisconsin
Posts: 294
Default

It's hard to tell from the pictures, but I'm assuming the bottom plate is recessed, and then there are holes drilled in that to increase surface area? Or are you only getting flow through the connections between holes?

Code:
+---|##|---|##|---|##|---+
|__M|##|MMM|##|MMM|##|M__|
+--\                  /--+
|   \WWWWWWWWWWWWWWWW/   |
+------------------------+



Side note: Does anyone know how to prevent multiple spaces being condensed into one?

Last edited by Arcturius; 11-25-2002 at 08:43 PM.
Arcturius is offline   Reply With Quote
Unread 11-24-2002, 04:01 PM   #9
g.l.amour
Cooling Savant
 
g.l.amour's Avatar
 
Join Date: Mar 2002
Location: on da case
Posts: 933
Default

the total idea of this method is that one needs no mill. so actually there are only the drilled holes with connections made with a dremel.

@puzzdre; i had almost the same feeling when i first fired my block. u invest money, time, sweat, blood so it is normal to expect some sort of small miracle. but, the freaks we all are, gaining 1 °C is already quite an accomplishment. thats because most of the systems we got here are already exploring the boundaries of WC. i think we both got carried away too much at making our blocks high flow. remember that brain design?

what might be a good idea is maybe to start a thread (if rotor doesn't mind) where we open-source minded discuss what can be done through rotor's method. as it seems to have been established by rotor that noone should use his method comercially (and right he is), then everyone using the method can help further refine it.

BillA has already given me some food for though,... anyway, the rotor style blox might not be the prettiest on the inside , but it must be possible to make them as performant as any milled out block. if we try to copy the best known waterblock for what is wanted to achieve; and compile it into a rotor design, then any maze/spiral/atlantis design should be possible.
__________________
yo soy un tiburón
g.l.amour is offline   Reply With Quote
Unread 11-24-2002, 04:11 PM   #10
Puzzdre
Cooling Savant
 
Puzzdre's Avatar
 
Join Date: Aug 2002
Location: Croatia
Posts: 969
Default

Yeah, recessed bottom with holes connected into the channels.

I have read what BillA suggested, think I'm gonna try 1.5-2 mm base in one chunk 10 mm thick, and I have some 5 mm thick 5 cm wide copper here for the flat top.

I don't want to sound dissapointed, it is just that I thought that I made my first setup 'from the hip', and considered it somewhat crappy and ghetto, but had some nice temps with crappy block. Guess I expected more to happen on the temp side, not to idle on 2 C higher...

Yup, live and learn, let's make some blocks!

g.l.: if you need some 5 mm copper, I can send you some. I have one chunk 50 cm long. Wanna share?
__________________
'Out of cheese error...
...please reboot the universe (press the GBL to continue)'
Puzzdre is offline   Reply With Quote
Unread 11-24-2002, 04:25 PM   #11
g.l.amour
Cooling Savant
 
g.l.amour's Avatar
 
Join Date: Mar 2002
Location: on da case
Posts: 933
Default

i was thinking more in the line of making some sort of plexi top. saves me alot of sawing + some weight.

and again, thx for offering. but sending one of the heaviest metals around by mail sounds a bit extravagant, no?

i thk i don't have the balls to make it 1.5 - 2mm. lets say i drill to depth 4 - 3.5 with the tip of the drill, that would mean that there are pits in extremis of 2.5 depth. given the crappy bench drill, and the error margin...

i think i will try to make something with a clearance(no pins) where the water enters the WB with very low BP thickness. and then have the surroundings a little more flow resisting.

anyway, what could be tested (since we didn't epoxy) is to disassemble, and put a flat top half. and watch...
__________________
yo soy un tiburón
g.l.amour is offline   Reply With Quote
Unread 11-24-2002, 04:33 PM   #12
Puzzdre
Cooling Savant
 
Puzzdre's Avatar
 
Join Date: Aug 2002
Location: Croatia
Posts: 969
Default

The problem will be dremel it to the depth of say 8 mm. At least with emery discs I have.
That's what I thought, 1.5 - 2 mm in the drill pits. A 'varialble base thickness' ...

NP for copper, if u change your mind, half of that slab is free for ya!

I can try to make the flat top on bottom half, but the base is still thick, and the passages cutted to half. Think I'll just drill another one...
__________________
'Out of cheese error...
...please reboot the universe (press the GBL to continue)'
Puzzdre is offline   Reply With Quote
Unread 11-25-2002, 07:02 AM   #13
g.l.amour
Cooling Savant
 
g.l.amour's Avatar
 
Join Date: Mar 2002
Location: on da case
Posts: 933
Default

never happy are we. think i'm first going to clean up the mess made in the living room, and afer that, start all over again...
__________________
yo soy un tiburón
g.l.amour is offline   Reply With Quote
Unread 11-25-2002, 07:17 AM   #14
Puzzdre
Cooling Savant
 
Puzzdre's Avatar
 
Join Date: Aug 2002
Location: Croatia
Posts: 969

Seems that we are happy while in process/progress...

I just printed out and sticked the pattern on chunk of copper...
First lunch, than drill press!

Good thing though, we know the drill...been there, done that...it's time for some new mistakes!
__________________
'Out of cheese error...
...please reboot the universe (press the GBL to continue)'
Puzzdre is offline   Reply With Quote
Unread 11-25-2002, 07:44 AM   #15
g.l.amour
Cooling Savant
 
g.l.amour's Avatar
 
Join Date: Mar 2002
Location: on da case
Posts: 933
Default

lool
__________________
yo soy un tiburón
g.l.amour is offline   Reply With Quote
Unread 11-25-2002, 07:50 AM   #16
Volenti
Cooling Savant
 
Volenti's Avatar
 
Join Date: Jan 2002
Location: in a nice cool spot
Posts: 427
Default

Quote:
Originally posted by Arcturius


Side note: Does anyone know how to prevent multiple spaces being condensed into one?
use [code]
__________________
feel free to icq/msn me, I'm always willing to toss around ideas.
Volenti is offline   Reply With Quote
Unread 11-25-2002, 08:57 PM   #17
Arcturius
Cooling Savant
 
Join Date: Aug 2001
Location: Chippewa Falls, Wisconsin
Posts: 294
Default

Thanks Volenti, that was really starting to irk me...

Puzzdre: how are things working out? I'm interested to see your results, as I'm currently working on a new direct-die system, and I'm wondering if it's really worth it (besides the HOLY SH!T look people give when they see you have water _actually_contacting_ your CPU)
Arcturius is offline   Reply With Quote
Unread 11-25-2002, 09:10 PM   #18
Volenti
Cooling Savant
 
Volenti's Avatar
 
Join Date: Jan 2002
Location: in a nice cool spot
Posts: 427
Default

I've got a p4 with direct die water cooling, details here ,I'm quite happy with it.
__________________
feel free to icq/msn me, I'm always willing to toss around ideas.
Volenti is offline   Reply With Quote
Unread 11-25-2002, 09:42 PM   #19
Arcturius
Cooling Savant
 
Join Date: Aug 2001
Location: Chippewa Falls, Wisconsin
Posts: 294
Default

I hope Puzzdre doesn't mind me hijacking his thread...

My first voyage into direct-die cooling was a K6-2 with the top two inches of a plastic pop bottle siliconed onto it. I added 14ml of water, and ran it for about 20m before I started getting air bubbles on the core. I didn't have a waterpump yet (and still don't have a decent one...) so I was basically just playing around.

I have since chipped the core, and it only works as a 166@3.5V (was originally a 350). Oh well. >
Arcturius is offline   Reply With Quote
Unread 11-26-2002, 01:00 AM   #20
Brad
Thermophile
 
Brad's Avatar
 
Join Date: Oct 2001
Location: Nuu Zeeelin
Posts: 3,175
Default

that block looks freaking amazing! Apart from the one hour to drill all the holes, how long did it take you in total?

The only thing you're missing is peltier support
__________________
2x P3 1100's at 1400, Abit VP6, 2x Corsair 256mb PC150 sticks, 20gb 'cuda ATA-III, 2x 40gb 'cuda ATA-IV in raid 0. 20" Trinitron. No fans

2x 2400+ at 2288mhz (16.0 x 143), Iwill MPX2, 2x Kingmax PC-3200 256mb sticks, 4x 20gb 60gxp in Raid 5 on a Promise SX6000. Asus Ti4200 320/630. Cooled by Water
Brad is offline   Reply With Quote
Unread 11-26-2002, 03:33 AM   #21
Puzzdre
Cooling Savant
 
Puzzdre's Avatar
 
Join Date: Aug 2002
Location: Croatia
Posts: 969
Default

Quote:
I hope Puzzdre doesn't mind me hijacking his thread...
NP

The results are satisfactional, at 25 C room temp, idle 35, full load 39 C. After changing the inlet barb to 10 mm ID, I got 35 idle, with 12 mm ID inlet idle was 36 according to MBM (if this is accurate at all). The pump is working quieter and smoother, this #Rotor's design really flows. I would say very low restrictive block. Seems the temps are little high due bp thickness of 5 - 6 mm (cannot say accurately cos of drill press being a cheap one, not so accurate on depth). Measuring the depth of the holes with vernier, seems like I got 4 mm hole plus drill point pit. It's little too thick.

Thanx Brad!
I really cannot say how long it took me to buil it, cos' I didn't have all the tools needed, went short on dremelling discs, short on tapping experience etc...It's all here in this thread (it started with a two pumps question, but evolved into blocks making):

http://forums.procooling.com/vbb/sho...5&pagenumber=2

I can assume that whole block can be made in three afternoons or less with no hurry. I'm making another one, and with experience in this first one, it goes much faster. I'll post the results here as it advance. This is what I've done for now, in about 2 and a half hours of work:

Punched the starting holes, cutted the top half to size (bottom half was pre-cut), drilled mounting holes, drilled and tapped tightening bolts holes, all sanded on the sides to fit nicely.

PS, thx for the idea on pelt mount!!! Are the 4 bolts enough for the 5 mm coldplate? If not, I should do some rearranging in drilling the holes...
Attached Images
File Type: jpg mk2-1.jpg (13.2 KB, 260 views)
__________________
'Out of cheese error...
...please reboot the universe (press the GBL to continue)'
Puzzdre is offline   Reply With Quote
Unread 11-26-2002, 03:34 AM   #22
Puzzdre
Cooling Savant
 
Puzzdre's Avatar
 
Join Date: Aug 2002
Location: Croatia
Posts: 969
Default

Here's preliminary assembly:
Attached Images
File Type: jpg mk2-2.jpg (6.2 KB, 260 views)
__________________
'Out of cheese error...
...please reboot the universe (press the GBL to continue)'
Puzzdre is offline   Reply With Quote
Unread 11-26-2002, 04:29 AM   #23
g.l.amour
Cooling Savant
 
g.l.amour's Avatar
 
Join Date: Mar 2002
Location: on da case
Posts: 933
Default

have u sawed those pieces yourself???

nice work, i thk now those designs will go alot faster.

when changing the middle barb to 10mm, u got better idle temp; but what about load temps?
__________________
yo soy un tiburón
g.l.amour is offline   Reply With Quote
Unread 11-26-2002, 05:28 AM   #24
Puzzdre
Cooling Savant
 
Puzzdre's Avatar
 
Join Date: Aug 2002
Location: Croatia
Posts: 969
Default

The load temp is still 39 C, it didn't change in any way...

The thicker (10 mm) piece is cut and flattened in machine shop, thinner piece I cutted with hacksaw, filed and sanded to fit. Man I wish to have a mill at least for this purposes!

Yup, when you know the way, it all goes much faster...It took me about 30 - 35 mins for this (variable depth hehe, big THX again #Rotor!!!)
Attached Images
File Type: jpg mk2-3.jpg (12.9 KB, 259 views)
__________________
'Out of cheese error...
...please reboot the universe (press the GBL to continue)'
Puzzdre is offline   Reply With Quote
Unread 11-26-2002, 05:57 AM   #25
g.l.amour
Cooling Savant
 
g.l.amour's Avatar
 
Join Date: Mar 2002
Location: on da case
Posts: 933
Default

wouldnt it be better creating some cavity in the middle with lets say a 10mm drill?

something like this.
Attached Images
File Type: jpg mk2-3.jpg (16.0 KB, 254 views)
__________________
yo soy un tiburón
g.l.amour is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 02:06 AM.


Powered by vBulletin® Version 3.7.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(C) 2005 ProCooling.com
If we in some way offend you, insult you or your people, screw your mom, beat up your dad, or poop on your porch... we're sorry... we were probably really drunk...
Oh and dont steal our content bitches! Don't give us a reason to pee in your open car window this summer...