I read and re-read where it was suggested that you put a breeze on the cpu, however, I missed the part where you did that.

Its my understanding that the air cooled cpu's move the hot air away from the thermistor that measures temp for the cpu. Placing a fan (to test) on the cpu area to move the stagnant air. If the cpu temp drops by a 2-4C from doing this, the mobo sensor is picking up the unmoved accumilated air around and under the cpu. Record the temp change. This amount can be removed from your watercooling temps as an error correction.

I am wondering where your 2 fans are that normally are placed near that empty space above your video card and to the left of your cpu.

i did do that with an 80mm fan and for some reason my temps went up. :shrug:

i have 2x80mm case fans above my video. u just cant see them.

i moved them to outside my case.

go to my gallery in my sig and u can see what i did.

I've tested both 947U w/ 92mm Tornado fan at 50% and Dangerden Maze4 on same system. The difference between air temperature and CPU diode temperature for the 947U/92mm Tornado@50% was 24.9C. The difference in water temperature and CPU diode temperature for the Maze4 at 0.5GPM flow rate (a LOW value) was 16.5C. So for the water cooling setup to do worse than air, your water temperature would have to be ~8.5C over room temperature. That's certainly possible with smallish radiators and quiet fans. The fact that increasing airflow through the radiators did very little to temperatures is disturbing though. Makes me suspect a faulty CPU temp reading more than anything else...

P.S. If you have everything outside the case, SHAKE that radiator and see if air comes out. They still need bleeding even when upright! Air in the rad will lower surface area for cooling a lot and the BI Micro2 doesnt have a ton to start with. I've used 2x BI Micros in parallel though and performance is better than any air cooling still.

how would i go about getting all the air out? just to be positive.

should i fill up the rad seperately and force it or what?

Dealing with trapped air - the lazy man's approach.

Easiest way though you needed to make sure EVERYTHING is clamped tight. (doubly sure this could cause a leak)

Constrict the tubing (i.e. squeeze it) for a few seconds were it leaves the radiator, and release. If there is air trapped you will hear gugglings and air bubbles should come shooting out.

Repeat.

There is physics behind that but its 4:42am and I'm tired so you'll just have to believe me. Slowely but surely you should start to collect any trapped air in your res - which you will then top up.

i tilted my case every which way other then flipping it, pinched the hose, shook it like a bad martini, tapped on the hose like a heroin needle. lol

nothing. :shrug:

im letting it run now til the morning to get all those lil ones out and then im going to boot it up.

i put it
pump->cpu->vga->radiator->resevoir.

and i can tell u one thing.
since i ditched that damn chipset block, i could tell the water was running wayyyyyyyyy faster.

so it was definetly the restricting force in my system.

now lets see if the rad holds up.

again ty to all who helped me.

I also have the Maze 4 CPU block and here's my results:
The Maze 4 CPU block needs very high flow rates to get good results. I had a very low restricted setup consisting of 1/2in ID tubing, LRS120 radiator from JP, Maze 4 CPU block, Via Aqua 375 GPH pump, and I used a T instead of a res. Since this was a very low restrictive setup, the Via pump was working very well and I was getting load temps of 43C at 2.03V at 30C case temps!

Then I decided to get the MCP600 pump because my Via was just too loud, the MCP600 puts out much less heat, I planned on adding a GPU block and replacing my Maze4 CPU block with a better block (all the better blocks are alot more restrictive than the Maze4).

After replacing my Via with the MCP600, my CPU load temps went up to 46C (maybe higher). I knew the MCP600 wasn't pumping water as fast as the Via because of how fast the bubbles were moving while I was bleeding.

yes, it will be less restrictive.

DangerDen is dead right now...
 

Tried to link to your heatercore link...DangerDens chok'in right now. Hope the server failure was planned updating or something. They probably thought no one would be there this time O' night. But I'm here, wanted to buy a TDX...oh well. Tomorrow...