Snap 1100 with no disk found
 

I am playing with a snap 1100. 250MB. It's not working, might have been erased for security purposes.

I reset it and assigned it an IP address and other settings.
I can access the web interface, I configured networking and I can access the web based UI. No problems at all.

Model Software Hardware Server # BIOS
1000 series 4.0.860 (US) 2.0.2 20XXXX 4.0.855

However, everything on the disk utilities page says
This page is not available because no disks were found.

Disk Status as of 6/13/2008 6:06:50 PM.
No disks found.

I took the drive out, a 250mb Maxtor and put it in an XP system, the bios reports the drive and the correct size, and logical disk manager does as well but unpartitioned. So that all seems to be working. I didn't muck with it. Just looked.

I put it back in the snapserver, and it cannot detect the disk is there. It is jumpered for master. Is that correct?

I contacted adaptec, told them I needed to reimage an 1100 and they immediately sent me a file, snap_sys.sup, 30093KB.

It's seemingly the exact same file I found on the GUESS site in an archive named
SnapOS_4_0_860_upg.exe which has assist, some help docs and three .sup files. One, the largest, is probably that same file. So I got the same file on the FTP site and direct from adaptec.

I tried to install the file as an upgrade both with the assist which chuggs along for several minutes then fails, and with the OS Update file browser on the snap server web based UI at /config?Func=ServerMenu which immediately says
Request Entity Too Large

I read some stuff about a knoppix boot method, but I was hoping that would not be necessary since I have a UI both through the Assist and directly in the server setup pages.

I read where a 1000V1 automatically formats a new disk. But this one doesn't seem to be doing that either because it's not a 1000V1 or the disk is not in a condition that allows it to be formatted automatically.

>A. The 1000v1 has the OS stored in flash ram, just install the hd. It takes about >10 min before you can connect to the web interface. There are 2 different image >files used to recover from a failed drivein the 1x00's.

>B. The 1000s normally use a 1000 image file, but if you get a 1 x 2 LED blinking >pattern it requires the 2200.img file.

>C. The 1000v2 requires an image file to be copied to the new drive. (Normally the >2200 image file)

>D. The 1100 requires an image file to be copied to the new drive. (Normally the >2200 image file)

Is the file Adaptec sent me the needed 2200 image file, or do I need a different file, or do I need to image that drive in another way?

So, what am I doing wrong? Is this a drive problem or has the disk interface in the snapserver somehow failed?

Thanks!

Re: Snap 1100 with no disk found
 

Adaptec does not use the hackers image file method. The factory has special software to load from the sup file.

What are the LED's doing when it comes up? At times the snap will run diagonistic on the drive (drive led). If it's doing this you will need to wait it out. It could take hours depending on what's it doing.

Normally installing in any Windows machine damages the snap file system. The ONLY THING THAT CAN READ A SNAP IS ANOTHER SNAP or a RECOVEY Service. If you stopped at the bios, your safe other wise you lost what was on there.

Re: Snap 1100 with no disk found
 

I don't care what was on there, like I said, It was likely erased for security purposes.

I didn't mount it on the windows system, just looked at it in the logical disk manager.

How can I reimage it?

Re: Snap 1100 with no disk found
 

I wonder why adaptec sent me the sup file then?
Drive LED is off.
System LED is blinking.
Net LED is blinking, less.

The thing cannot find it's disk. That's the problem that needs to be fixed.
Is this the KNOPPIX boot fix I need? I can do that. Are there clear step by step directions?

Re: Snap 1100 with no disk found
 

Dave , am I reading his post wrong? It is inconsistent.

First, he says it is a 1100 unit, but his specs state it is a 1000 unit. Maybe it is a type o because of his bios is consistent with a 1100(4.0.855).
Secondly, how is he able to read the specs of the hard drive if he claims he needs an image for the hard drive? If your SnapOS is on the hard drive then you can read the specs , if it is not then you cannot read the specs.
If I were you I would try and pull the image off the hard drive, because if you can read the specs then you still have a some what of a SnapOS on the hard drive. You also might be able to reinstall the SnapOS with the file Adaptec sent you via Assist.

bitor

Re: Snap 1100 with no disk found
 

If it was erase for security that's fine. But how did you know what the specs were? Were you able to read the specs before the HD was erased? Or were you able to read the specs after the HD was erased?

bitor

Here is a link to Snap LED , etc stuff

http://wiki.procooling.com/index.php/Snap_Server

Re: Snap 1100 with no disk found
 

The front of the unit says 1100 as does the sticker on the bottom, which also says 250GB.

When I click the logo at the top of the web interface, the popup opens with specs and says

Model Software Hardware Server # BIOS
1000 series 4.0.860 (US) 2.0.2 20XXXX 4.0.855
Well, read the specs of the hard drive? No, but I can read them off the label of the hard drive. The snap unit cannot detect the drive at all. I never said I could read the specs of the drive in software. Where did you see that?

As to assist, I did use assist on it, told it to put the image I got from adaptec on it and it chugged for a few minutes before it failed. I only used the 30 MB image, there are two other images, a jvm image and a sync image. I tried those but no success reported by assist.

As I said I also used the web interface's file browser to try an upgrade. It gave the error message I cited. The web interface DOES work, and I was able to put an IP in and all with no problem. But there is no drive. Hardly useful.

Re: Snap 1100 with no disk found
 

When you use the Assist can you see your unit. Does Assist recognize the unit you have? If it does then you should be able to use the sup file provided this sup file is not the upgrade file. I believe you stated that Adaptec sent you a file. If that doesn't work, it looks like you need an image in order to get your unit up and running.
Yeah I forgot that the Snap1100 in the webGUI if you click on the logo it says Snap1000. When you say there is no hard drive do you mean that you have no hard drive installed? Or it doesn't see the hard drive?
In any even, it looks like you need an image by the problems you are having. Getting an image will be a problem. I don't know where you will be able to get one in order to get your unit working.

bitor

Re: Snap 1100 with no disk found
 

Assist recognizes and attempts to put the image on the drive, then fails.

It doesn't see the hard drive.
One thing, the drive is jumpered master, I assume that is correct.
Well, there is lots of stuff on the .?? site. If I knew which I needed it would be helpful. I assume the image Adaptec sent me is the correct one, but the person I spoke to didn't ask my server number if that matters, though I did mention the model to her.

But the image doesn't work. Or the drive doesn't work. Or there is another failure.

One question: If I put the drive in a windows system and format and test the drive, can I then reimage it after that with the snap image? I could QC the drive that way. If the drive is broken I am essentially wasting my time with that drive.

Re: Snap 1100 with no disk found
 

Try setting the drive to CS and see if that helps. The older units have problem sometimes with drive reconition. What brand drives, Maxtor have know to calls problems at times.

It sound like you have one the early 1100's. They are a very strange bread. Because it has flashram. If the drvie is clean with the OS in flashram, watch the led patterns as it comes up. It will give clues on on whats going on.

Re: Snap 1100 with no disk found
 

You need the image file from a hard drive(other then your own HD) that already has a good SnapOS on it. The files that Adaptec sent you is for installing on a preexisting SnapOS that is already functioning(working) on a Snap Server. The "image" is a copy that you would rip so to speak(see how to make an image from the forum) from a working drive that already has a good working SnapOS on it. Then you copy it to your hard drive.

So ANY sup file you got(or will get or find) is not what you need. You need a copy in .bin format of a preexisting good SnapOS from another drive to copy on to your drive. Without this you are out of luck.
Redundant , but I hope the point is clear.

bitor

Re: Snap 1100 with no disk found
 

I have a working Snap 1000 with a 40 gb drive. Would that drive work to reimage the 250 GB drive in the 1100?

I have to say since I have this nice flash based UI it does seem like the snapserver is working. I was under the impression the UI was all on the disk, but in this model that is clearly not the case. The disk is completely unnecessary for me to use the UI, assign IP address, pw, etc. Proof is I was able to do all that and I have no disk.

Some of these snapservers can apparently prep a new drive and do so automatically as soon as you put one in. This 1100 is not like that?

Maybe the drive is just bad.

Re: Snap 1100 with no disk found
 

It should work. What do you have to loose? Follow the directions in the forum on how to image and post back if it works or not.
Follow link for info:
http://wiki.procooling.com/index.php...de_Information

My understanding of the flash models that work like that(automatically install the SnapOS) are the much older ones. The newer ones I believe do not function that way. The flash however holds some important configure information but is only good IF the SnapOS image is installed on the hard drive.

bitor

Re: Snap 1100 with no disk found
 

I think the 2-minute rule applies here, but I never pay attention to that, so here is my bull in the china shop reply.

First, it sounds as if he has a FLASHRAM OS unit.

If yes, then he does not need an image!!!! (this is what I think he has)

If no, then something is all wacked out here in the conversation. How is he seeing stuff at all if it is not booted up and in the OS....


Second, if it is the FLASHRAM unit, then.. Dude, WIPE THE DRIVE... I mean No data, no partitions, no formats. WIPED!!!! Then try again.. Bet it works...

This assumes it has OS 3.4.803 or above (for drives larger than 128MB), which I have to assume it does since he said it was a 250GB unit in the first place.

Re: Snap 1100 with no disk found
 

The 1000 and 1100's use different OS modules. My experieces is a 49/51 chance it may, leaning toward not. If it does you need to reload the the OS from the sup file.

To confirm flashram boot with out HD and see of the gui comes up. It's also possiable the MB was replaced with a 1000 model.

If flashram unit give it 20 min and see with a clean HD like Andy said. I have worked on one of these in them middle transition units and they are flaky.

Re: Snap 1100 with no disk found
 

It seems as if there is a file SnapOS corruption on his hard drive. Due to either bad sectors or a bad install or etc..
I've had enough of these units to know if the SnapOS is not installed correctly you can get access to the WebGUI, BUT the SnapOS does NOT properly work correctly.
However, Dave is correct. Just remove the drive and if you get webGUI then you have FLASH RAM OS. But I tend to think it needs to be re imaged and I would guess that it is not flash ram os.
Hopefully, he will be able either way to fix his problem.
bitor

Re: Snap 1100 with no disk found
 

OK, now we're getting somewhere.
I unplugged the HDD and removed it from the unit.
Powered it up. I had previously set the ip address to 192.168.1.30 and was able to access the web gui with either a web browser or with Assist.

With the HDD removed I cannot access any of that either way.

I just re inserted the HDD and I can access the web gui again at the same IP. Assist also finds the unit.

So it appears it is loading something off the drive but the drive is not found by any of the utilities. No flash rom here.

Check or Repair Disk says
This page is not available because no disks were found.

As do all the other pages on the Disk Status page.

So now we know. The disk does work, but the storage area is not being found, though it seems likely the settings that I set, IP address, server name, pw, are stored on the disk that I cannot otherwise access.

The server log page says:
Severity legend: I=Information, W=Warning, E=Error, F=Fatal Error, S=Server Startup
Message Source Date Time
E LCD Message : FAILED: Disk 1 System 6/14/2008 2:54:44 PM
S System Initialization : Server v4.0.860
Build Date: Mar 2 2005 17:50:55
Boot Count: 11 System 6/14/2008 2:54:34 PM

Obviously the data area needs to be reformatted which is a function on the disk maint page, but since the disk it not found I can't do that.

So what's the next step? I think we have proven the disk does work, but there is some sort of corruption that is preventing the data area from being available.

Is there a command in the debug window to force initialization?

Re: Snap 1100 with no disk found
 

Do you have debug access?

IF so use the "co de format 10000/init" to init the drive. If not I would suspect you have a damaged os, or disk.

You can also try reloading the OS using Assist by putting the unit in FLUP mode (5 blink pattern). If you try this have the snap in the FLUP mode atleast 30-45 sec before trying to push the sup down.

Re: Snap 1100 with no disk found
 

I pasted that line in the debug window, no success.

6/14/2008 19:02:44 Command: co de format 10000/init

Invalid device id 10000 requested

------------
Command returned with console error 1.


I just put it in 5 blink mode, but do I hold down reset for restart, or do I just push the update down with assist while it is blinking? The directions here say to continue reset but the 5 blink state is not really reset, like the 1-4 blinks.

So, after I get the disk light blinking 5x what then?

OK, I got the disk light blinking 5x and held down reset.
The unit restarted. The system and disk lights are blinking 1x together. The link light is on steady.

I have been trying to access it with assist. No success. Assist says "The ip address of the server is currently in use or unreachable."

I cannot connect with assist nor with the IP address via the web interface in this mode. Assist does seem to see it, but it might be lying. It's on the list and I can get info which is correct.

Here is my system log, same as before.

Message Source Date Time
E LCD Message : FAILED: Disk 1 System 6/14/2008 7:30:12 PM
I INIT: Setting IP address to 192.168.1.30 Network 6/14/2008 7:30:02 PM
S System Initialization : Server v4.0.860
Build Date: Mar 2 2005 17:50:55
Boot Count: 14

Re: Snap 1100 with no disk found
 

You need to follow the instruction using Assist to update the OS. During the process you will be asked to put the server into FLUP mode. 5 blinks is FLUP mode.

Re: Snap 1100 with no disk found
 

I haven't found any instructions like that, either on the forums or on the wiki.

Can you point me to specific directions? I would appreciate it.

I found this, but there is no mention of FLUP mode.
My server does appear in green so it appears this is the procedure, and I have done this. But no success.

Re: Snap 1100 with no disk found
 

During this process you will be prompted to put the unit in FLUP mode.

Your down to where you need to try a Image file, there is nothing else that can be done at this time. The 1100's in most all cases uses a 2200.bin file, but I have seen early models use the 1000.bin file.

Re: Snap 1100 with no disk found
 

I have done that process, at no time during that process with assist am I prompted to put the server in FLUP mode. Nevertheless I have put it in FLUP mode and tried that very process and assist cannot find the server for upgrade, though it still appears as green in the list and I can still get information on it.

So I am stopped.

I have a .sup file, Snap_4_x.sup, 29.3 MB (30,815,135 bytes) in size.

Another, that was sent to me by adaptec, snap_sys.sup 29.3 MB (30,814,256 bytes)

Re: Snap 1100 with no disk found
 

You have already tried using the admin gui upgrade option. Since this has failed, you need to have a 2200 image file to reload the HD. The OS sounds like it is corrupted beyound repair.

Re: Snap 1100 with no disk found
 

OK, what is the exact name and size of the archive that contains the 2200 image file?

The one I received from Adaptec was called
snapos_34807.exe
containing folder
SnapOS_34807
containing file
snap_sys.sup
of size 29.3 MB (30,814,256 bytes)

But that seems to not be the correct file.

Re: Snap 1100 with no disk found
 

Steevo:

This file(bin file) is something that you will not find at Adaptec or can simply ask them for it because they do not have it. The files they have once again are for upgrading a unit that is in good working order. Here is my post I posted before that explained what you HAVE to do.
There is NO OTHER WAY around it.

I wrote before...

"You need the image file from a hard drive(other then your own HD) that already has a good SnapOS on it. The files that Adaptec sent you is for installing on a preexisting SnapOS that is already functioning(working) on a Snap Server. The "image" is a copy that you would rip so to speak(see how to make an image from the forum) from a working drive that already has a good working SnapOS on it. Then you copy it to your hard drive.

So ANY sup file you got(or will get or find) is not what you need. You need a copy in .bin format of a preexisting good SnapOS from another drive to copy on to your drive. Without this you are out of luck.
Redundant , but I hope the point is clear.

bitor"

***end***

That's it Steevo...Re read Dave's post on the bin image information here. It tells you just about everything you need to know. But once again, Adaptec will not have what you need because they do NOT have it.

bitor

Re: Snap 1100 with no disk found
 

Well, I have other units, that work. I read where someone was posting such files years ago and Adaptec had a fit about it. Clearly I could find one of those files on BT or somewhere and clone that to my 250GB. But it would be helpful to know the name of the needed file.

I have a 40 GB model 1000, but I have a hard time understanding how if I were to clone the contents of that 40 GB to my 250GB using Digital Dolly I will have a working 250GB, but I guess it could happen.

Is that way I need to do? Get the complete contents off a 40 GB drive and clone that to the 250GB? I can do that.

But you understand how confusing all this is. How can that work? I dunno.

Re: Snap 1100 with no disk found
 

You can try the 1000, but I think the odds are against you. There may be enough to boot it, then reload the OS. The image file has been called several things 2200.bin, Snap2200.bin are the most common. The 1100 and 2200 are the only SnapOS units with the OS on the HD.

You do not need to do any thing with the 1000. Just read the boot tracks ~25 meg to a file ( or directly to 250gig HD) with Digital Dolly. Then reinstall the HD back into the 1000.

Digital Dolly is a disk utiliy that does a RAW read, came from the unix world. Most imaging software try to inturpit the file structure and fail. DD give you a cmd line so you can specify how many meg you want, or copy the complet HD if you like. If you copy the complete HD it will show only 40 gig on the 250gig HD, and will take some time to do. Then you will have to reinit wiping the HD to get full capacity.

But I would recommend backing up the 1000 before removing the HD. The cmd line is not forgiving it you make a mistake and get the source and dest reversed. I would recommend removing all other HD from the PC to be used, this way you can match the instructions to the letter.

Before I would do any of this. I would boot the 1100 and leave it on over night then see if it comes up. This is one of the biggest mistakes users make, not giving it enough time to do what it needs to do.

If by chance you have a copy of Spinrite I would run it on maintance mode and see if it does any repair. If it gets past the 4-7% range the drive should be good.

Re: Snap 1100 with no disk found
 

I left it on for a couple of days, it never changed during that time.

I have another 1100 with an 80GB, but I can't get anywhere with it, no ui, cannot connect with assist, nothing. It seems failed. I did reset it with 4 blinks. I got nothing.

Would you recommend I find a working 1100 of any capacity to clone from?

I may be able to come up with one. If that is better than the one working 1000 for some reason. I really don't understand the difference between these models in this instance.

Re: Snap 1100 with no disk found
 

The 1100 & 2200 have the OS on the HD. All the other models (1000, 2000, 4000, 4100) have the OS in Flashram. On the flashram models all you need to do is install install a clean HD and the snap will auto format and install the OS. With the 1100 & 2200 the OS is on the HD so if a drive fails your down with no way to revive the unit without a image file. This is the hackers way of course since we do not have the factroy software.

So if you can find a working 1100 or 2200 the os is close enough for it to boot the snap.

On your 1100, you apparenty have a corruped OS that does not allow you to repair. Nornally if it boots you can reload the OS. But only the same version or newer. The reason you need to try a image file for recovery.

The 1000 are a odd bread. I have seen some that take a 1000 image while some require the 2200. The 1000 have a slower cpu and less ram if one of the earlier ones. The ones with less ram do not play well with v4 OS.