Pro/Forums

Pro/Forums (http://forums.procooling.com/vbb/index.php)
-   General Liquid/Water Cooling Discussion (http://forums.procooling.com/vbb/forumdisplay.php?f=9)
-   -   FAO Cathar (http://forums.procooling.com/vbb/showthread.php?t=11855)

gurdas 06-20-2005 08:34 AM
FAO Cathar
 
Not sure if you remember me (ordered 8 or so of your blocks in the UK). I have your LRWW and the base has some slight marks, whats the best method of taking these out? Would you recommend me polishing the base again or will I run risk of making it too thin?

Also do you have an email address I can contact you on.

Thanks

DrCR 06-20-2005 12:12 PM
Try PMing him. :)

Tempus 06-20-2005 03:16 PM
plasma cutter - great for taking out a few marks.

Cathar 06-20-2005 05:39 PM
A quick hand-lap with 1200-grit paper on a flat, using (low smell) kerosene as a cutting lubricant, will be the best way to remove any marks and won't have a significant impact on the base-plate thickness.

Really though it shouldn't be anything to worry about.

killernoodle 06-20-2005 05:55 PM
Quote:
Originally Posted by Tempus
plasma cutter - great for taking out a few marks.
Dont you mean ball peen hammer?

Cathar 06-20-2005 05:58 PM
Quote:
Originally Posted by killernoodle
Dont you mean ball peen hammer?
Don't you meen "ball-pein hammer"?

gurdas 06-24-2005 12:00 PM
Quote:
Originally Posted by Cathar
A quick hand-lap with 1200-grit paper on a flat, using (low smell) kerosene as a cutting lubricant, will be the best way to remove any marks and won't have a significant impact on the base-plate thickness.

Really though it shouldn't be anything to worry about.
Thanks for that, I maybe just paranoid so i'll leave it.

Do you happen to have any spare black bolts used to fix the 3 plates together?

Cathar 06-24-2005 07:29 PM
Quote:
Originally Posted by gurdas
Do you happen to have any spare black bolts used to fix the 3 plates together?
Yes, but it'll be cheaper and faster for you to go to a bolt & fastener supply store and just ask for some "M4x12mm SHCS" in Stainless Steel. The black ones can go a little rusty after a while and so I switched to holding all blocks together with stainless steel bolts.

SHCS = Socket Head Cap Screw

gurdas 06-25-2005 07:47 AM
Would something like this suffice?

http://www.trident-uk.com/shop/acatalog/F841.jpg

The description says

SS.A4.Pan.Hd.M/Screw M4X12mm POZI

gurdas 06-25-2005 07:49 AM
Have also found this which is what you said

Tool-NET M4 x 12 BZP Socket Head Cap Screw

But could I use the POZI head instead of having to use an allen key or do I need to use a SHCS?

JfRsQ 07-01-2005 01:17 AM
Harder to strip a socket head than a Posi one. You can also tight them more than the +. I wouldn't use them :rolleyes:

Joe Camel 07-03-2005 08:26 AM
the threads are in SILVER...im sure you could strip them with just about ANY "screw" :rolleyes:

HERE is a thread over on OC where the G5 gets lapped. (and i learn to wet-lap)



.

CYberDruid 07-04-2005 01:24 PM
Quote:
Originally Posted by Joe Camel
the threads are in SILVER...im sure you could strip them with just about ANY "screw" :rolleyes:

HERE is a thread over on OC where the G5 gets lapped. (and i learn to wet-lap)



.
Thank you for the tour of lapland--I used to think it was excessive--but the results speak for themselves. Great insights from Cathar and others in the crosslink. thanks!


All times are GMT -5. The time now is 12:47 PM.

Powered by vBulletin® Version 3.7.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
(C) 2005 ProCooling.com
If we in some way offend you, insult you or your people, screw your mom, beat up your dad, or poop on your porch... we're sorry... we were probably really drunk...
Oh and dont steal our content bitches! Don't give us a reason to pee in your open car window this summer...