SnapServer 2200 - Alternate Power Supply
 

Hi folks !

I am using two Snaps 2200 and currently the PSUs are still good, however i have a fishy feeling.

So to be prepared for the worst, here a question for the hardware gurus on the board hehe

Is it possible to use an alternate Power supply for the snap servers, that has a bit more punch (especially for the more power hungry HDDs out there)

I was thinking on the lines of maybe a old Notebook psu wich are pretty easy to get on Ebay.

Would that be feasable ? Connect the two wires to the original plug and ready to go. At least thats how my simple mind imagines it.

Anyone has any experience with this ?

Regards

Klaus

Re: SnapServer 2200 - Alternate Power Supply
 

Many users have had to replace their power supplies. I think from loosing them or purchased them on eBay and was not included. As long as it's large enough to carry the load it will work. If you go what is know as a switcher they are physicaly smaller and have a big punch.

Re: SnapServer 2200 - Alternate Power Supply
 

While I did a Power MOD for the 4000, I cannot say on the 2x00 units. Their case is totaly different and I have not had one in my hands to really look at. Sorry :(

Re: SnapServer 2200 - Alternate Power Supply
 

The 2200 uses a external power supply like the 1x00 modes. 12vdc

The 2000 model is internal.

Re: SnapServer 2200 - Alternate Power Supply
 

LOL :laugh2:

My point exactly!

<------------ no use when it comes to 2x00 units...

Re: SnapServer 2200 - Alternate Power Supply
 

Hi there

Thanks for the input, now i can see what the specs on the psu are and then start taking a look around on ebay, but now i can be sure that my general thinking was into the right direction :)

thanks

regards

klaus

Re: SnapServer 2200 - Alternate Power Supply
 

You need a minimum 1 amp, 12vdc.

Re: SnapServer 2200 - Alternate Power Supply
 

Good Morning !

OK but taking a 2 amp, 12 vdc (assuming i find one) would not damage the unit, correct ? As long as the voltage stays the same ?

Re: SnapServer 2200 - Alternate Power Supply
 

You are kidding right? David? :uhh:

More like 3A 12VDC minimum with 2 Drives. And more, if you plan on using large drives.

Re: SnapServer 2200 - Alternate Power Supply
 

Yes, it requires a 3.5A if he had searched the forum he would have found it. The 2000 have 50-65w power supply. Believe it or not but some of the early 1000 used a 1.2 amp with a delay start.

EPS Model F1670K if you want what comes with it.

Re: SnapServer 2200 - Alternate Power Supply
 

Don't worry mate, I got you covered David... :D


Mate? Damn, I been talking to those guys in OZ land too much... :dome:

Re: SnapServer 2200 - Alternate Power Supply
 

Hey Phoenix , don't be a drongo or I'll hit you with a chozwozza :) .

Anyways back to the subject.......

If your going to get a PSU try to get one thats a switchmode type , a switchmode PSU is smaller , lighter , more efficient , has better regulation and usually is cheaper.

With the current issue (get it , current issue) , if your 2200 needs 3.5 amps it will try to suck 3.5 amps out of your PSU so you will need a PSU supply that can supply 3.5 amps.
If your power supply can supply a bazzilion amps your 2200 will still try to suck 3.5 amps, the thing is try to get a PSU that can supply more than your 2200 needs ( but don't go overboard now ).

As an example here in Oz (stares at Phoenix :) ) a 12V PSU that can supply 5A costs about $35US

I hope this helps.

Oh and remember to check that the connector you use on the PSU is wired up OK ( the person who sold you the PSU should help you with this).

that's about it from me 8)

Mike 8)