Pro/Forums

Pro/Forums (http://forums.procooling.com/vbb/index.php)
-   General Liquid/Water Cooling Discussion (http://forums.procooling.com/vbb/forumdisplay.php?f=9)
-   -   My new watercooling setup - comments..? (http://forums.procooling.com/vbb/showthread.php?t=4338)

007 09-09-2002 06:26 PM

My new watercooling setup - comments..?
 
Here's a few pics of my new watercooling setup, which consists of:
EpoX 8K3A+, 768MB TwinMos PC2700 RAM, unlocket XP1800+, Seagate Barracuda ATA IV 80GB, GF2 MX200, DD Maze2, Eheim 1048, 12mm vinyl tubing (gonna replace that with silicone tubing), Blackice Rad, resevoir from a model airplane and Chieftech big tower:

The Front:
http://chrhansen.homepage.dk/diverse_billeder/1.jpg

Front Open: Fanbus and drives:
http://chrhansen.homepage.dk/diverse_billeder/2.jpg

The Goodies Inside ;-)
http://chrhansen.homepage.dk/diverse_billeder/3.jpg

The Radiator 'fanduct' made by me ;-). It's completely seperated from other heatsources, keeping the water and the inside cool:
http://chrhansen.homepage.dk/diverse_billeder/4.jpg

Pump and the suspension making it totally quiet, drives and MB:
http://chrhansen.homepage.dk/diverse_billeder/5.jpg

Rear of the rad and exhaust fans (today i've siliconed the rad to the duct, so that all airflow goes through the rad - don't know if it has improved anything, but it can't hurt :)
http://chrhansen.homepage.dk/diverse_billeder/6.jpg

And finally the exhaustfans from inside (they are running, so my Mavica digi-cam must have pretty good close-time ;-)
http://chrhansen.homepage.dk/diverse_billeder/7.jpg

Comments/suggestions are welcome, if you want specific pictures of anything, or explanations, please write me or here in the forums:
It's running pretty smooth at 1838MHz (10,5*175 and 2,00V) temps are:
idle: 41C and load 46C - using the XP diode (i think, no one seems to know where to find a program, that can tell me whether it uses the diode or the in-socket thermister (spelled right? ;)).
Any ideas how to get i higher? and do you think it's safe to up the volt's to 2.2?

BTW: the temp. on the front is the waterblock temp, measured on top of the block

gmat 09-10-2002 05:58 AM

I like the suspended 1250 :)
Those fans are full of dust man... A good cleaning won't hurt :p
Ah and this backside cut would be wayyy nicer with some trim...
Oh why is the PSU not horizontal ? Looks weird...
Have fun.

g.l.amour 09-10-2002 09:33 AM

it looks a bit like my case, inexperienced, cutting too much away with a dremel... trial and error stuff. i was thinking myself of buying a new case and mounting all my stuff again so i have learned from my previous errors.

honestly, looking at the front it looks tidy, but as gmat points out; digging on the inside and the back reveals some imperfections. looks like from the practical point u got a good cooling setup, and for some of us that is more important than the beauty contests.

but euh, tell us what u think of it yourself, stuff u would do differently and such.

cheers

SCompRacer 09-10-2002 01:30 PM

http://home.attbi.com/~scompracer/ol...r_complete.jpg

I did something similar in my first water cooled case 007, except I had the radiator at the top and the fan mounted on the outside of the rear panel drawing air through the radiator. The angled baffle had foam on the edges to seal against the case sides. I cut the old panel out above the PS since it originally held two 80mm fans. I made a new plate from aluminum to cover the hole for a 120mm fan.

You can get a thin piece of metal and install it over your cut out area on the rear of case. Just mark and cut holes for your radiator and power supply, screw or rivet it to rear of case. That will give your PS some support.

If I understand correctly, you are blowing air through the radiator rather than drawing air through it. Otherwise you would pick up heated air from the PS. I tape my sensor to the top of the CPU touching the core.

nikhsub1 09-10-2002 01:54 PM

The 8K3A/+ uses the on CPU diode with an XP CPU.

Kevin 09-10-2002 02:20 PM

hehe yeah that it is a pretty dusty fan setup there and the hose is a lil brownish looking, but AWESOME job with the radiator shrouding and suspended pump mount!
-Kevin

SCompRacer 09-10-2002 03:21 PM

Quote:

Originally posted by nikhsub1
The 8K3A/+ uses the on CPU diode with an XP CPU.
It was in response to his "BTW: the temp. on the front is the waterblock temp, measured on top of the block."

007 09-11-2002 03:39 PM

Thanks for all the nice words. Yesterday i tried upping the volts to 2.2 - shouldn't have done that - fried the MB and possibly the CPU :(
No matter what i try, it won't boot - the led-diosplay on the MB wouldn't show any codes, and the PSU just powers the fan down after a fwe seconds... tried it with the incase PSU - it won't do anything at all - not even power up. i have an extra 250W - it powers up the PSU only, and the RPMK on the fan falls as it was going idle). the 12V line showed 13,5 just before i died - think that's the explanation...
any advices?

I have a MSI KIT266 Pro2 RU lying around, gonna put that in tonight, and se if it's gonna boot... I also have a spear locked XP1700 - gonna put that in too, to see if the MSI will boot with that, to se if the CPU is fried... other than that, things are fine here in Denmark... (very upset about trying the 2.2V!!!)

BTW: i know about the back - it's UGLY :) gonna fix that with some sheet-metal i have lying around - should be nice and clean... and yes - it is the first WC setup, i've made with alle the stuff inside the case (was getting pretty tired of not being able to move it around...). and the fanbus on the front - gonna make a new plate and align them all - it's just difficult, because the front won't close, if they aren't in exactly the right place...

gmat 09-11-2002 03:51 PM

Sounds like the 12V line blew up. Overload, maybe.
That's why overclocking is an extreme sports :rolleyes: - the risk.
There are PSU's around with overload + overtemp shutoff protection. They are expensive but such is the price for peace of mind (and health of components)

g.l.amour 09-12-2002 02:16 AM

i don't get it, if i up the vcore too much from PSU point of view, then my pc will start to crash randomly (i think). back off the vcore and i'm okay again. my PSU is a 250W model (think i get first prize for the lightest PSU on this board) and whenever i go over 1.8V , it seems like it can't take that.

i was once able to blow up mobo and proc, but that was by letting the WB sit loosely on proc, until after 5 sec i smelled a nice processor roast. i will not smoke weed anymore before doing infrastructural work on my computer.

gmat 09-12-2002 04:11 AM

The PSU output is transformed and regulated on the mobo itself to feed the CPU.
It's pumping the 5V and 12V lines - thats why modding the vcore will stress those lines.
The 12V line is commonly sollicited to power modern CPUs and GPUs, because transporting high currents with 12V is way more efficient than doing so with 5V.
Thats why by modding the vcore *directly* to 2.2 he may have produced a fatal overload, which is fatal with an unprotected PSU.

g.l.amour 09-12-2002 07:56 AM

thx

pHaestus 09-12-2002 11:05 AM

Quote:

i will not smoke weed anymore before doing infrastructural work on my computer. [/b]
If Canadia really legalizes, this warning should be on every baggie :)

hmale 09-12-2002 02:27 PM

Often times the most overlooked component in any system is the PSU. It is just not sexy enough for some of us to pay attention to.

For better or for worse the "enthusiast"...overclockers and such need to pay very special attention to the PSU. PSUs with sufficient power, good line regulation, and safety mechanisms will more than pay for themselves in the long run.

Cheers!

pHaestus 09-12-2002 03:50 PM

For the price, I thinkthat the 400W Sparkle PSU is hard to beat. It has a LOUD fan in it by default however, and can benefit from substitution of a thermally controlled 80mm fan.

I have found cases where improved PSU resulted in 100MHz higher overclocks, but I have similarly seen cases where RAM upgrades solved the problem. So YMMV.

bigben2k 09-12-2002 04:04 PM

I started another thread in the hardware section, about using a couple of 300W to make a 600W PSU. Post your comments!

{clicky} Go to the thread


All times are GMT -5. The time now is 09:17 AM.

Powered by vBulletin® Version 3.7.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
(C) 2005 ProCooling.com
If we in some way offend you, insult you or your people, screw your mom, beat up your dad, or poop on your porch... we're sorry... we were probably really drunk...
Oh and dont steal our content bitches! Don't give us a reason to pee in your open car window this summer...