Pro/Forums - View Single Post - What could I expect from this wc setup? advice

@/2ct!< · 07-04-2004, 11:57 PM

Allright, I have more or less narrowed down what my setup will probably be like. First, I will have MCW6002 cpu block and probably a maze 4 gpu, though I have seen few comparisons amongst gpu blocks.l. Im also looking at the mcp600 pump. Im looking into WA2s heatercores, basically a Caprice.
Now, for the real questions/controversy.
1. I am more than likely going to mount my HC at the top of the case.(P160) I will be able to get more unrestricted airflow there and a bigger HC than if I went front, even though I will have warmer air.
a.Is it better to have this large HC in top rather than a Dtek Jr. Size in a restricted front?
b. I can only fit one shroud in the top. Will a Caprice in the top with only pulling fans be better than a Jr. with push/pull?
c. My other components seem fairly restrictive, will I see decent results with a larger HC compared to a normal size? ( I wanted to get a 2-342, but it just wouldnt fit

)
2. I plan to use 3/8 id tubing. Everything in my setup has 1/2" barbs, therefore it I am guessing I will get good performance, only slightly worse than the same system with different tubing only.
a. Will 3 /8 system actually be better if I would have to either kink 1/2" or use elbows
b. DD says 3/8 can strecth over 1/2" barbs, I want to make sure this is true
3. I am strongly considering a T-line being placed at the end of the system, under the GFX card as seen in many systems. I plan to have a short 1/2 id tube run to the pump inlet on one side of the T.
a. Will this allow for sufficient pump work?

Overally, what I am trying to do is get a system that works darn good, even though it is not technically optimal. I am mainly asking because it seems my setup goes against everything pH taught and he is either ashamed at my disregard of his guides or is laughing at my stupidity.

07-04-2004, 11:57 PM	#1
@/2ct!< Cooling Neophyte Join Date: Nov 2003 Location: Colorado Posts: 11	What could I expect from this wc setup? advice Allright, I have more or less narrowed down what my setup will probably be like. First, I will have MCW6002 cpu block and probably a maze 4 gpu, though I have seen few comparisons amongst gpu blocks.l. Im also looking at the mcp600 pump. Im looking into WA2s heatercores, basically a Caprice. Now, for the real questions/controversy. 1. I am more than likely going to mount my HC at the top of the case.(P160) I will be able to get more unrestricted airflow there and a bigger HC than if I went front, even though I will have warmer air. a.Is it better to have this large HC in top rather than a Dtek Jr. Size in a restricted front? b. I can only fit one shroud in the top. Will a Caprice in the top with only pulling fans be better than a Jr. with push/pull? c. My other components seem fairly restrictive, will I see decent results with a larger HC compared to a normal size? ( I wanted to get a 2-342, but it just wouldnt fit ) 2. I plan to use 3/8 id tubing. Everything in my setup has 1/2" barbs, therefore it I am guessing I will get good performance, only slightly worse than the same system with different tubing only. a. Will 3 /8 system actually be better if I would have to either kink 1/2" or use elbows b. DD says 3/8 can strecth over 1/2" barbs, I want to make sure this is true 3. I am strongly considering a T-line being placed at the end of the system, under the GFX card as seen in many systems. I plan to have a short 1/2 id tube run to the pump inlet on one side of the T. a. Will this allow for sufficient pump work? Overally, what I am trying to do is get a system that works darn good, even though it is not technically optimal. I am mainly asking because it seems my setup goes against everything pH taught and he is either ashamed at my disregard of his guides or is laughing at my stupidity.