Pro/Forums - View Single Post

Fast420A · 11-02-2004, 07:54 AM

The only thing I am missing is the mounting hardware for the waterblock as I needed some of it on my current maze 3 setup that was missing pieces when I bought it used and I can't find where I put the rest of the parts for it at. This is a COMPLETE compressor setup out of an older 1960's - 1970's Cavalier Coke Machine. The compressor uses R12 and gets VERY cold. I don't know the specs on it but I had a Tbred B 1700 @ 2.4 Ghz under load at 11c. Here's the post of when I found this and got it running.

As for what is being sold, the whole compressor assembly which has a thermostat for easy use. The thermostat at the warmest setting would shut off the compressor with the evaporator temp at 0 degrees or so. Depends on where you setup the thermostat probe on the evaporator or in the water.

The water mixture was getting down to -9ºC or so and the evap was down to -20ºC or so at the coldest I saw inside of a cheap plastic 30 qt ice chest which will also be included. The ice chest has a slot for the compressor pipe and the water hoses to go in as well as the pumps cord.

The pump is a Modded Via Aqua 1300 that has 3/8 quick connect fittings on it from a previous setup and works fine submerged or inline but you'll be submerged with this setup. The quick connects are JB Welded inplace so don't break them or you'll need to come up with another way of attaching the discharge tube to the pump. The intake is fine with nothing on it or with a 3/8 tube in it. This pump never had a problem sitting in a water/alcohol/antifreeze mixture at -9ºC.

The block is a Danger Den Maze 1 that has the plexi mount with holes for AMD and holes for P4 but I had to cut down one of the edges of the mount to clear the mobo capacitors so the P4 holes are right on the edge of the plexi. The plexi has a little explanding foam on it still from when it was installed but it won't matter as you will need to cover the whole block with it anyways. There are even the hoses on the block still that have foam and duct tape on them for insulation which worked very well.

I'll even include the 5 1/4 bay cheapo dual temp sensor so you can monitor temps of the coolant and evaporator.

I will ship this and you will pay for shipping. I will box this up so it is completely safe and will arrive that way to you completely insured.

Quick rundown of everything you get:

Complete Compressor Assembly
30 Qt Plastic ice Chest with slot for tubing
Maze 1 AMD/P4 setup minus mounting hardware. (10 minutes in Home Depot and you should be set to mount it)
Insulated Hoses on waterblock.
Via Aqua 1300 with 3/8 quick connects Jb Welded on for no leaks. (I will silent mod it again if you want me too.)

Looking for $200 OBO plus shipping.

11-02-2004, 07:54 AM	#1
Fast420A Cooling Neophyte Join Date: Aug 2003 Location: Tampa, FL Posts: 5	Almost Complete Chiller Setup The only thing I am missing is the mounting hardware for the waterblock as I needed some of it on my current maze 3 setup that was missing pieces when I bought it used and I can't find where I put the rest of the parts for it at. This is a COMPLETE compressor setup out of an older 1960's - 1970's Cavalier Coke Machine. The compressor uses R12 and gets VERY cold. I don't know the specs on it but I had a Tbred B 1700 @ 2.4 Ghz under load at 11c. Here's the post of when I found this and got it running. As for what is being sold, the whole compressor assembly which has a thermostat for easy use. The thermostat at the warmest setting would shut off the compressor with the evaporator temp at 0 degrees or so. Depends on where you setup the thermostat probe on the evaporator or in the water. The water mixture was getting down to -9ºC or so and the evap was down to -20ºC or so at the coldest I saw inside of a cheap plastic 30 qt ice chest which will also be included. The ice chest has a slot for the compressor pipe and the water hoses to go in as well as the pumps cord. The pump is a Modded Via Aqua 1300 that has 3/8 quick connect fittings on it from a previous setup and works fine submerged or inline but you'll be submerged with this setup. The quick connects are JB Welded inplace so don't break them or you'll need to come up with another way of attaching the discharge tube to the pump. The intake is fine with nothing on it or with a 3/8 tube in it. This pump never had a problem sitting in a water/alcohol/antifreeze mixture at -9ºC. The block is a Danger Den Maze 1 that has the plexi mount with holes for AMD and holes for P4 but I had to cut down one of the edges of the mount to clear the mobo capacitors so the P4 holes are right on the edge of the plexi. The plexi has a little explanding foam on it still from when it was installed but it won't matter as you will need to cover the whole block with it anyways. There are even the hoses on the block still that have foam and duct tape on them for insulation which worked very well. I'll even include the 5 1/4 bay cheapo dual temp sensor so you can monitor temps of the coolant and evaporator. I will ship this and you will pay for shipping. I will box this up so it is completely safe and will arrive that way to you completely insured. Quick rundown of everything you get: Complete Compressor Assembly 30 Qt Plastic ice Chest with slot for tubing Maze 1 AMD/P4 setup minus mounting hardware. (10 minutes in Home Depot and you should be set to mount it) Insulated Hoses on waterblock. Via Aqua 1300 with 3/8 quick connects Jb Welded on for no leaks. (I will silent mod it again if you want me too.) Looking for $200 OBO plus shipping. __________________ FOLD TEAM 32 2.4C @ 3400 Mhz 2100 Tbred @ 2400 Mhz Last edited by Fast420A; 11-09-2004 at 02:54 PM.