Joe: quick question on the MagDrive 250 fittings...

lisch · 01-05-2001, 06:46 PM

Joe, i noticed you have used these mag drive pumps by Danner for some time now; i think im going to order the 250 GPH model, but was wondering what kind of connections come on the in/out ports? 3/8" ID right? so all i need it to thread coper 3/8" barbs into them to connect to the hoses right?

thanks..

Joe · 01-05-2001, 07:22 PM

you using one of the bog mag drives or lil ones? ( not sure if if its the lil 250 or not)

------------------
C-ya
Joe - Owner/Editor
www.ProCooling.com
Where the Completely Addicted Come to Cool Off

Somebody set up us the bomb.

lisch · 01-05-2001, 07:47 PM

oh sorry, i didnt order it yet, i was waiting to figure this out...

i was gona get the litle one; the 250 GPH Supreme Mag Drive; it looks just like the ones from your DH1/2 articles.. its like 33 bucks...

Joe · 01-05-2001, 07:54 PM

those are 1/2" fittings on there, so you need to adapt them to what ever hose fitting you will be running

------------------
C-ya
Joe - Owner/Editor
www.ProCooling.com
Where the Completely Addicted Come to Cool Off

Somebody set up us the bomb.

lisch · 01-05-2001, 08:10 PM

ok, sorry to be lame in this, 1/2" fittings means you would use 1/2" OD hose, w/ 3/8" Inner Diameter. right?

same for most all waterblocks etc.. so the most used hoses are 3/8" ID like what you used in your DH3 rig.. so i wouldnt have to make adapters for 1/2" fittings right?

Joe · 01-05-2001, 08:23 PM

the pumps in DH3 are small and have 3/8" hose barbs itself so there were no converters needed. ( they are also only 150GPH per pump)

On the supreeme Mag Drive pumps its a 1/2" ID that needs to be converted to a 3/8" hose barb.

The top fitting is 1/2" OD and needs to be converted to 3/8" hose barb

------------------
C-ya
Joe - Owner/Editor
www.ProCooling.com
Where the Completely Addicted Come to Cool Off

Somebody set up us the bomb.

lisch · 01-05-2001, 08:27 PM

ok, thanks! that help a lot.
so those just screw in w/ tape then...

Joe · 01-05-2001, 08:54 PM

I would use Plumbers goop to seal the fittings, its more of a perm deal, but it will make sure its water tight.

------------------
C-ya
Joe - Owner/Editor
www.ProCooling.com
Where the Completely Addicted Come to Cool Off

Somebody set up us the bomb.

01-05-2001, 06:46 PM	#1
lisch Cooling Neophyte Join Date: Jan 2001 Location: Cleveland Ohio Posts: 22	Joe: quick question on the MagDrive 250 fittings... Joe, i noticed you have used these mag drive pumps by Danner for some time now; i think im going to order the 250 GPH model, but was wondering what kind of connections come on the in/out ports? 3/8" ID right? so all i need it to thread coper 3/8" barbs into them to connect to the hoses right? thanks..

01-05-2001, 07:22 PM	#2
Joe The Pro/Life Support System Join Date: Dec 1999 Location: Denver, CO Posts: 4,041	you using one of the bog mag drives or lil ones? ( not sure if if its the lil 250 or not) ------------------ C-ya Joe - Owner/Editor www.ProCooling.com Where the Completely Addicted Come to Cool Off Somebody set up us the bomb.

01-05-2001, 07:47 PM	#3
lisch Cooling Neophyte Join Date: Jan 2001 Location: Cleveland Ohio Posts: 22	oh sorry, i didnt order it yet, i was waiting to figure this out... i was gona get the litle one; the 250 GPH Supreme Mag Drive; it looks just like the ones from your DH1/2 articles.. its like 33 bucks...

01-05-2001, 07:54 PM	#4
Joe The Pro/Life Support System Join Date: Dec 1999 Location: Denver, CO Posts: 4,041	those are 1/2" fittings on there, so you need to adapt them to what ever hose fitting you will be running ------------------ C-ya Joe - Owner/Editor www.ProCooling.com Where the Completely Addicted Come to Cool Off Somebody set up us the bomb.

01-05-2001, 08:10 PM	#5
lisch Cooling Neophyte Join Date: Jan 2001 Location: Cleveland Ohio Posts: 22	ok, sorry to be lame in this, 1/2" fittings means you would use 1/2" OD hose, w/ 3/8" Inner Diameter. right? same for most all waterblocks etc.. so the most used hoses are 3/8" ID like what you used in your DH3 rig.. so i wouldnt have to make adapters for 1/2" fittings right?

01-05-2001, 08:23 PM	#6
Joe The Pro/Life Support System Join Date: Dec 1999 Location: Denver, CO Posts: 4,041	the pumps in DH3 are small and have 3/8" hose barbs itself so there were no converters needed. ( they are also only 150GPH per pump) On the supreeme Mag Drive pumps its a 1/2" ID that needs to be converted to a 3/8" hose barb. The top fitting is 1/2" OD and needs to be converted to 3/8" hose barb ------------------ C-ya Joe - Owner/Editor www.ProCooling.com Where the Completely Addicted Come to Cool Off Somebody set up us the bomb.

01-05-2001, 08:27 PM	#7
lisch Cooling Neophyte Join Date: Jan 2001 Location: Cleveland Ohio Posts: 22	ok, thanks! that help a lot. so those just screw in w/ tape then...

01-05-2001, 08:54 PM	#8
Joe The Pro/Life Support System Join Date: Dec 1999 Location: Denver, CO Posts: 4,041	I would use Plumbers goop to seal the fittings, its more of a perm deal, but it will make sure its water tight. ------------------ C-ya Joe - Owner/Editor www.ProCooling.com Where the Completely Addicted Come to Cool Off Somebody set up us the bomb.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)