![]() | ||
|
|
General Liquid/Water Cooling Discussion For discussion about Full Cooling System kits, or general cooling topics. Keep specific cooling items like pumps, radiators, etc... in their specific forums. |
![]() |
Thread Tools |
![]() |
#1 |
Cooling Savant
Join Date: May 2004
Location: Northern VA
Posts: 383
|
![]()
http://www.ltnt.ethz.ch/researchprojects.php?id=13
Linked from http://www.frostytech.com/ Hoots "I have a dream" block except aluminum instead of copper. man wouldnt that al foam disintegrate after a few weeks? |
![]() |
![]() |
![]() |
#2 |
c00ling p00n
Join Date: Jun 2002
Location: L.A.
Posts: 758
|
![]()
Yeah that seems to be the general concept IIRC.
__________________
*:-.,_,.-:*'``'*:-.,_,.-:*'``'*:-.,_,.-:*'``'*:-.,_,.-:*'``'*:-.,_,.-:* E6700 @ 3.65Ghz / P5W DH Deluxe / 2GB 667 TeamGroup / 1900XTX PC Power & Cooling Turbo 510 Deluxe Mountain Mods U2-UFO Cube Storm G5 --> MP-01 --> PA 120.3 --> 2x DDC Ultras in Series --> Custom Clear Res "Artificial intelligence is no match for natural stupidity." 1,223,460+ Ghz Folding@Home aNonForums *:-.,_,.-:*'``'*:-.,_,.-:*'``'*:-.,_,.-:*'``'*:-.,_,.-:*'``'*:-.,_,.-:* |
![]() |
![]() |
![]() |
#3 |
Cooling Neophyte
Join Date: Dec 2002
Location: Twin Cities
Posts: 67
|
![]()
Actually, fate has allowed me to cross paths with a source for a small (one blocks worth) amount of the copper equivalent to that stuff. It's taking "the slow boat from China" getting here. In the mean time I have to come up with a way to either bond it to a plate or plate up one face until its thick enough to lap flat. Both are daunting tasks as I'm told it melts quite easily when trying to silver solder it to a plate, not to mention the wicking issue. I'm told it loves sucking solders better than tinned braid. When it eventually arrives, I post a picture. Unfortunately, I am sworn to secrecy as to the source or I'd gladly put you on to it.
It is not my first choice as a media due to its low mass as opposed to sintered beads, but I had the opportunity to get some to play with and couldn't say no. Hoot
__________________
DFI LP UT NF4 Ultra-D 7.04-3 Bios A64 3700+ San Diego 11x257 (2827 Mhz) @ 1.57Vcore 2x1Gb Crucial Ballistix 7:6 (300 Mhz) 3-3-3-8-1T @ 2.77V Connect 3D x850xt 620/625 2x WD 36GB Raptors in Raid0 DIY Jet Impingement WB on CPU / Pipecap WB on GPU Shrouded Camaro Heater Core / Swiftech MCP655 Pump Antec P-160 Tower / Seasonic S12 600W PSU MAXIM 6658 Thermal Diode Reader Moderator at OCForums |
![]() |
![]() |
![]() |
#4 |
CoolingWorks Tech Guy Formerly "Unregistered"
Join Date: Dec 2000
Location: Posts: 2,371.493,106
Posts: 4,440
|
![]()
interesting project Hoot
|
![]() |
![]() |
![]() |
#5 |
Cooling Savant
Join Date: May 2004
Location: Northern VA
Posts: 383
|
![]()
Im guessing laying out a very thin layer of AS epoxy on a copper/silver base then just putting the sintered copper on the epoxy would create a horrible contact in terms of thermal conductivity?
|
![]() |
![]() |
![]() |
#6 |
Thermophile
Join Date: Sep 2002
Location: Charlotte, NC
Posts: 1,014
|
![]()
How much does this stuff compress? Is there no possibility of just pressing it on there slightly between two plates?
What about trying to mount it SMD style with a hot air bath with just the base tinned (very thin layer of course)? How was it mounted to that aluminum block in the first link?
__________________
I have a nice computer. |
![]() |
![]() |
![]() |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|