Chillers???

Havoc · 08-01-2001, 07:10 PM

Ok, what is up with this...http://data-detective.com/overclock/chillers.html

Everthing I have read on chillers says it does not work. Is this corect or is this page correct?

What I want to do is a closed loop on the CPU with a cooling block running back to this chiller and back to the cpu using an inline pump. In the chiller I want to put 3 156 watt peltiers. I'll figure out how to power them once I get an answer to the original question on whether chiller work. Then on the hot side I will have it going to two big radiators not sure which ones yet and then on to a reservoir and inline pump.

Here is a diagram:

->--->-->- ->->-big radiator 1-->--
| | | |
| | | |
CPU Chiller big radiator 2
| | | |
| | | |
--<--<--<- -<-Pump-<-reservoir-<---

Think this would work? Not cheap but fun

<--Havoc--{{{

Mbeach · 08-02-2001, 07:02 AM

imo it works as long as you can keep the water in the block long enough to chilled.
I also wanted to try just this same thing, but in smaller scale. Just to get the water down to perhaps 20-25C.

btw, you play UT (instaGIB) on swedish servers? Your nick is very familiar.

Kevin · 08-04-2001, 01:04 PM

Chip does his differently. He recirculates the water through the chiller blocks. He doesn't use them as a single pass chiller.

Amy · 08-16-2001, 11:06 PM

HAVOC:

Check this one out...
http://www.octools.com/forum/cgi-bin...&num=997644689

Just two 80W 8A High Clamping pressure on a Intel CPU = 8C - A peltier Sandwich
- About right for T-Bird OC'ed.

As you can see when Primary side is below ambient, no primary side Radiator is required.

Cheers Amy

-

08-01-2001, 07:10 PM	#1
Havoc Cooling Neophyte Join Date: May 2001 Posts: 2	Chillers??? Ok, what is up with this...http://data-detective.com/overclock/chillers.html Everthing I have read on chillers says it does not work. Is this corect or is this page correct? What I want to do is a closed loop on the CPU with a cooling block running back to this chiller and back to the cpu using an inline pump. In the chiller I want to put 3 156 watt peltiers. I'll figure out how to power them once I get an answer to the original question on whether chiller work. Then on the hot side I will have it going to two big radiators not sure which ones yet and then on to a reservoir and inline pump. Here is a diagram: ->--->-->- ->->-big radiator 1-->-- \| \| \| \| \| \| \| \| CPU Chiller big radiator 2 \| \| \| \| \| \| \| \| --<--<--<- -<-Pump-<-reservoir-<--- Think this would work? Not cheap but fun <--Havoc--{{{

08-04-2001, 01:04 PM	#3
Kevin Slacking more than your weird uncle Join Date: Nov 2000 Location: San Diego, CA (UCSD) / Los Angeles, CA (home) Posts: 1,605	Chip does his differently. He recirculates the water through the chiller blocks. He doesn't use them as a single pass chiller. __________________ I used to throw hot coffee all over the ass of the horse there, then whip him while he was kickin' at me. Those f***in things are crazy.

08-16-2001, 11:06 PM	#4
Amy Cooling Neophyte Join Date: Jul 2001 Location: So Calif Posts: 44	HAVOC: Check this one out... http://www.octools.com/forum/cgi-bin...&num=997644689 Just two 80W 8A High Clamping pressure on a Intel CPU = 8C - A peltier Sandwich - About right for T-Bird OC'ed. As you can see when Primary side is below ambient, no primary side Radiator is required. Cheers Amy - __________________ VP6 Dual PIII-750E@1028 Muskin HSDRAM

08-02-2001, 07:02 AM	#2
Mbeach Cooling Neophyte Join Date: Jul 2001 Location: Gothenburg Posts: 18	imo it works as long as you can keep the water in the block long enough to chilled. I also wanted to try just this same thing, but in smaller scale. Just to get the water down to perhaps 20-25C. btw, you play UT (instaGIB) on swedish servers? Your nick is very familiar.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)