maze 3 bad temps

Jscamry · 01-06-2003, 04:34 PM

hey all i just ordered wattering cooling prodcuts for myself for x-mas. I purchased a hydor L30 320gph, Maze 3 luctie top, 10 ft of clear clear flex tubbing. I bought heatercore from a local autoparts store, its 6x6x2, I also made a shroud w/ a 120mm fan pulling air through the hc. The order my setup follows is pump-> WB->HC->Res->pump.

My comp contains Asus A7m266, AMD xp 1800, 300W generic power supply, 2 sticks of pc2100 256mb, abit siluro Geforce 4 MX440, western digital 100gig HDD, 3com adsl modem and a nic. and two rear exhaust fans
my temps are 47c just surfing the net, when i started the comp and pump from a cold start the temps were 34c.yeah my room is about 80-85f and i am not sure about the case temps. I am using the asus pc probe to find out my proc temps. yes i have done a stress test w/ prime 95 for a few hrs it gets to about 51c.

I have taken the setup apart many times to check that the wb is seated properly, i have also applied AS the way the web site suggest, i even tried to apply a thicker coat of AS the the proc. I have added 1 oz of watter wetter.

thanks all any help would be appc..

bigben2k · 01-06-2003, 05:06 PM

You've done your homework, nice rig!

Now lap that block...

I think you'll find your water temp to be only a few degrees above ambient.

On the other hand, the A7M266 is a dual proc board... so maybe your cooling solution needs tweaking.

What's your water temp?

Jscamry · 01-06-2003, 06:11 PM

how do i lap the wb? the water temps are about 26c thats using a raytek temp gun tha i use for my nitro rc cars.... is there anything better to use to get a more accurate reading for my wc setup then the pc probes? also how do i test the waterflow and the temps of my water, anything i can buy?? and my board is not a dual proc board it just has the spcket for the one board...

thanks J.

bigben2k · 01-06-2003, 06:36 PM

A good old thermometer, dipped into the water...

For a lapping guide, you can google for:
+"lapping guide"

Plenty of results!

As for the mobo, I'm guessing then that you have an Asus A7N266, and not A7M266?

AS works much better, when there's very little of it. As a guide, put a tiny dot on, then spread it as thin as you can with a razor blade. That's it.

What model fan do you have on your rad?

Jscamry · 01-06-2003, 07:24 PM

thanks again for the help. yeah i have the Asus A7m266. the fan that i have on my hc is a DC Centaur, here are the specs

Max static pressure: 82.3 Pa ( 8.4 mm H2O )
Max airflow: 2.8 Cubic meter per minutes
Current : 0.9 A at rated voltage
Locked rotor current: 2.3 A
Speed: 2650 rpm
Ambient temp.: -20 to +50
Isnsulation resistance: 10 Mohm
Dielectric strength: 500VAC for 1 minute

p.s. i have some pics of mysetup how do i post pics on here?

thaks jason

bigben2k · 01-06-2003, 07:44 PM

Ok, first, a little conversion...

82.3 Pa = 0.33 inch water column (excellent). 2.8 Cubic meter per minutes = 99 cfm (not great). Overall, that fan is good!

Is it a DC centaur mark 5 or a DC Centaur 3 blade ?

To post a pic, you can attach one (max per post), or if you have a host, click on the [img] button to specify the link to it.

Sorry about the mobo confusion, I was thinking about the A7M266-D, not A7M266.

Let us know what you want to try!

Jscamry · 01-06-2003, 08:43 PM

its the 5 blade model

Jscamry · 01-06-2003, 08:52 PM

trying to post pics

Jscamry · 01-06-2003, 10:56 PM

MadDogMe · 01-07-2003, 03:51 AM

Is your block the right way up?, there's been a few 'Maze3 Bad Temps?' posts lately

, do a search and look at the pics for orientation of block...

01-06-2003, 04:34 PM	#1
Jscamry Registered User Join Date: Dec 2002 Location: Oviedo,Fl Posts: 6	maze 3 bad temps hey all i just ordered wattering cooling prodcuts for myself for x-mas. I purchased a hydor L30 320gph, Maze 3 luctie top, 10 ft of clear clear flex tubbing. I bought heatercore from a local autoparts store, its 6x6x2, I also made a shroud w/ a 120mm fan pulling air through the hc. The order my setup follows is pump-> WB->HC->Res->pump. My comp contains Asus A7m266, AMD xp 1800, 300W generic power supply, 2 sticks of pc2100 256mb, abit siluro Geforce 4 MX440, western digital 100gig HDD, 3com adsl modem and a nic. and two rear exhaust fans my temps are 47c just surfing the net, when i started the comp and pump from a cold start the temps were 34c.yeah my room is about 80-85f and i am not sure about the case temps. I am using the asus pc probe to find out my proc temps. yes i have done a stress test w/ prime 95 for a few hrs it gets to about 51c. I have taken the setup apart many times to check that the wb is seated properly, i have also applied AS the way the web site suggest, i even tried to apply a thicker coat of AS the the proc. I have added 1 oz of watter wetter. thanks all any help would be appc..

01-06-2003, 05:06 PM	#2
bigben2k Responsible for 2% of all the posts here. Join Date: May 2002 Location: Texas, U.S.A. Posts: 8,302	You've done your homework, nice rig! Now lap that block... I think you'll find your water temp to be only a few degrees above ambient. On the other hand, the A7M266 is a dual proc board... so maybe your cooling solution needs tweaking. What's your water temp? __________________ WBTA (Water Block Testing Alliance) Nordic Hardware WC 101

01-06-2003, 06:36 PM	#4
bigben2k Responsible for 2% of all the posts here. Join Date: May 2002 Location: Texas, U.S.A. Posts: 8,302	A good old thermometer, dipped into the water... For a lapping guide, you can google for: +"lapping guide" Plenty of results! As for the mobo, I'm guessing then that you have an Asus A7N266, and not A7M266? AS works much better, when there's very little of it. As a guide, put a tiny dot on, then spread it as thin as you can with a razor blade. That's it. What model fan do you have on your rad? __________________ WBTA (Water Block Testing Alliance) Nordic Hardware WC 101

01-06-2003, 07:44 PM	#6
bigben2k Responsible for 2% of all the posts here. Join Date: May 2002 Location: Texas, U.S.A. Posts: 8,302	Ok, first, a little conversion... 82.3 Pa = 0.33 inch water column (excellent). 2.8 Cubic meter per minutes = 99 cfm (not great). Overall, that fan is good! Is it a DC centaur mark 5 or a DC Centaur 3 blade ? To post a pic, you can attach one (max per post), or if you have a host, click on the [img] button to specify the link to it. Sorry about the mobo confusion, I was thinking about the A7M266-D, not A7M266. Let us know what you want to try! __________________ WBTA (Water Block Testing Alliance) Nordic Hardware WC 101

01-06-2003, 06:11 PM	#3
Jscamry Registered User Join Date: Dec 2002 Location: Oviedo,Fl Posts: 6	how do i lap the wb? the water temps are about 26c thats using a raytek temp gun tha i use for my nitro rc cars.... is there anything better to use to get a more accurate reading for my wc setup then the pc probes? also how do i test the waterflow and the temps of my water, anything i can buy?? and my board is not a dual proc board it just has the spcket for the one board... thanks J.

01-06-2003, 07:24 PM	#5
Jscamry Registered User Join Date: Dec 2002 Location: Oviedo,Fl Posts: 6	thanks again for the help. yeah i have the Asus A7m266. the fan that i have on my hc is a DC Centaur, here are the specs Max static pressure: 82.3 Pa ( 8.4 mm H2O ) Max airflow: 2.8 Cubic meter per minutes Current : 0.9 A at rated voltage Locked rotor current: 2.3 A Speed: 2650 rpm Ambient temp.: -20 to +50 Isnsulation resistance: 10 Mohm Dielectric strength: 500VAC for 1 minute p.s. i have some pics of mysetup how do i post pics on here? thaks jason

01-06-2003, 08:43 PM	#7
Jscamry Registered User Join Date: Dec 2002 Location: Oviedo,Fl Posts: 6	its the 5 blade model

01-06-2003, 10:56 PM	#9
Jscamry Registered User Join Date: Dec 2002 Location: Oviedo,Fl Posts: 6

01-07-2003, 03:51 AM	#10
MadDogMe Thermophile Join Date: Aug 2002 Location: Just shut up ;) ... Posts: 1,068	Is your block the right way up?, there's been a few 'Maze3 Bad Temps?' posts lately , do a search and look at the pics for orientation of block...

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)