Help me understand the graph

Brandon_Tyler · 05-13-2005, 05:36 PM

The way I see the WB comparison graph and understand how the temp and block work. Then I should see a dramatic temp loss in my swifty 6002 compared to my maze 4 correct. if I currently idle at ~34C what can I expect after the swifty install?

-Brandon

jaydee · 05-13-2005, 06:13 PM

Depends on your flow rate but your looking at a couple C lower. Idle temps may not be all that different but load temps (much more important than idle temps) should be better.

Brandon_Tyler · 05-13-2005, 06:45 PM

okay given the fact Ive got 2 Hydor L30's in series how is that going to affect the outcome?

-Brandon

and thanks jaydee116

jaydee · 05-13-2005, 08:53 PM

Whats in the rest of the system?

Brandon_Tyler · 05-13-2005, 11:41 PM

DoH! I guess that might be important.. 2 chevy caprice heater cores about 6 feet of clearflex 60 the above mentioned swifty 6002a and a maze 4 acetal top.

-B!

jaydee · 05-14-2005, 08:22 AM

Rough guess would be about 2C drop. Without knowing the pressure losses and flow rate through the system it is hard to give a solid answer.

nikhsub1 · 05-14-2005, 11:25 AM

I would say closer to 3C, but yeah, between 2 and 3C. That would be my estimate.

Brandon_Tyler · 05-15-2005, 12:13 PM

Okay much to my own dismay over this, After 10 yes 10 remounts of the 6002a on my NF7s I'm getting horrible temps. on my old maze4 I could get temps around 32-35 idle depending on room temp. Currently with the last mounting I'm idling near 50C!!!!!!! with a room temp of arounf 68 F and a case temp of 23-24C. IU cannot for the life of me figure out whats going on. I would think this block would lower temps not raise them so much I'm paranoid to run my box. Can somone offer some type of guidance plase.

-Brandon

eander315 · 05-15-2005, 03:17 PM

The problem may be elsewhere in your loop. Did you change anything else when you upgraded the block? Check your tubing for kinks and other flow restrictions, make sure both pumps are operating properly, and give the whole system a general going-over. Are you sure your 6002 is mounted properly and not resting against the socket or some other obstruction? How does the thermal paste look when you remove it? What happens to the temps if you re-install the Maze 4? Can you post close-up pictures of the system?

pHaestus · 05-15-2005, 03:22 PM

Make sure you have the holddown for the Swiftech block so that the springs are positioned correctly (they are different to get proper load on CPU) and make sure that the clip is engaging all 6 lugs fully.

05-13-2005, 05:36 PM	#1
Brandon_Tyler Cooling Neophyte Join Date: Nov 2004 Location: D-FW, Texas Posts: 26	Help me understand the graph The way I see the WB comparison graph and understand how the temp and block work. Then I should see a dramatic temp loss in my swifty 6002 compared to my maze 4 correct. if I currently idle at ~34C what can I expect after the swifty install? -Brandon

05-14-2005, 11:25 AM	#7
nikhsub1 c00ling p00n Join Date: Jun 2002 Location: L.A. Posts: 758	I would say closer to 3C, but yeah, between 2 and 3C. That would be my estimate. __________________ :-.,_,.-:'``':-.,_,.-:'``':-.,_,.-:'``':-.,_,.-:'``':-.,_,.-: E6700 @ 3.65Ghz / P5W DH Deluxe / 2GB 667 TeamGroup / 1900XTX PC Power & Cooling Turbo 510 Deluxe Mountain Mods U2-UFO Cube Storm G5 --> MP-01 --> PA 120.3 --> 2x DDC Ultras in Series --> Custom Clear Res "Artificial intelligence is no match for natural stupidity." 1,223,460+ Ghz Folding@Home aNonForums :-.,_,.-:'``':-.,_,.-:'``':-.,_,.-:'``':-.,_,.-:'``':-.,_,.-:

05-15-2005, 03:22 PM	#10
pHaestus Big Player Making Big Money Join Date: Aug 2001 Location: irc.lostgeek.com #procooling.com Posts: 4,782	Make sure you have the holddown for the Swiftech block so that the springs are positioned correctly (they are different to get proper load on CPU) and make sure that the clip is engaging all 6 lugs fully. __________________ Getting paid like a biker with the best crank... -MF DOOM

05-13-2005, 06:13 PM	#2
jaydee Put up or Shut Up Join Date: Dec 2001 Location: Spokane WA Posts: 6,506	Depends on your flow rate but your looking at a couple C lower. Idle temps may not be all that different but load temps (much more important than idle temps) should be better.

05-13-2005, 06:45 PM	#3
Brandon_Tyler Cooling Neophyte Join Date: Nov 2004 Location: D-FW, Texas Posts: 26	okay given the fact Ive got 2 Hydor L30's in series how is that going to affect the outcome? -Brandon and thanks jaydee116

05-13-2005, 08:53 PM	#4
jaydee Put up or Shut Up Join Date: Dec 2001 Location: Spokane WA Posts: 6,506	Whats in the rest of the system?

05-13-2005, 11:41 PM	#5
Brandon_Tyler Cooling Neophyte Join Date: Nov 2004 Location: D-FW, Texas Posts: 26	DoH! I guess that might be important.. 2 chevy caprice heater cores about 6 feet of clearflex 60 the above mentioned swifty 6002a and a maze 4 acetal top. -B!

05-14-2005, 08:22 AM	#6
jaydee Put up or Shut Up Join Date: Dec 2001 Location: Spokane WA Posts: 6,506	Rough guess would be about 2C drop. Without knowing the pressure losses and flow rate through the system it is hard to give a solid answer.

05-15-2005, 12:13 PM	#8
Brandon_Tyler Cooling Neophyte Join Date: Nov 2004 Location: D-FW, Texas Posts: 26	Okay much to my own dismay over this, After 10 yes 10 remounts of the 6002a on my NF7s I'm getting horrible temps. on my old maze4 I could get temps around 32-35 idle depending on room temp. Currently with the last mounting I'm idling near 50C!!!!!!! with a room temp of arounf 68 F and a case temp of 23-24C. IU cannot for the life of me figure out whats going on. I would think this block would lower temps not raise them so much I'm paranoid to run my box. Can somone offer some type of guidance plase. -Brandon

05-15-2005, 03:17 PM	#9
eander315 Cooling Neophyte Join Date: Jan 2005 Location: Houston Posts: 34	The problem may be elsewhere in your loop. Did you change anything else when you upgraded the block? Check your tubing for kinks and other flow restrictions, make sure both pumps are operating properly, and give the whole system a general going-over. Are you sure your 6002 is mounted properly and not resting against the socket or some other obstruction? How does the thermal paste look when you remove it? What happens to the temps if you re-install the Maze 4? Can you post close-up pictures of the system?

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)