waterblock measurement ?

simplesid · 04-05-2002, 05:29 AM

here is what i come up with...

GF3 Ti 200 GPU ... 40X40mm mounting ears 57mm center to center

CPU block ... 72X72mm mounting 36mm @ 66mm 2mm raise above cam box

NB ... SAME AS GPU ?

one more thing what do you guys think of mag drive pumps ?
found 500GPH $51.99 US
350GPH $45.00 US

DigitalChaos · 04-05-2002, 10:05 AM

i have no idea BUT i have some info that may be of use:
my friends Gainward GF3 heat sink... the pins on that did not fully reach the holes for the chipset on his Abit mobo... id say it was not more than 5mm smaller in reach.

Brad · 04-05-2002, 03:16 PM

it depends on the NB, many boards don't even have mounting holes.

mag drive pumps are what most of us use, I'm just not sure on what brand those are. Probably Danner looking at those prices, Danner is a good brand

simplesid · 04-05-2002, 04:41 PM

yes it is a danner pump...
NB has mounting holes im useing a shuttle AK35GTR

mkosem · 04-05-2002, 04:58 PM

my mobo(p4s333) and my vid card( aopen ti200) have the same mounting holes.

--Matt

04-05-2002, 05:29 AM	#1
simplesid Cooling Neophyte Join Date: Mar 2002 Location: USA Posts: 18	waterblock measurement ? here is what i come up with... GF3 Ti 200 GPU ... 40X40mm mounting ears 57mm center to center CPU block ... 72X72mm mounting 36mm @ 66mm 2mm raise above cam box NB ... SAME AS GPU ? one more thing what do you guys think of mag drive pumps ? found 500GPH $51.99 US 350GPH $45.00 US Last edited by simplesid; 04-05-2002 at 06:37 AM.

04-05-2002, 03:16 PM	#3
Brad Thermophile Join Date: Oct 2001 Location: Nuu Zeeelin Posts: 3,175	it depends on the NB, many boards don't even have mounting holes. mag drive pumps are what most of us use, I'm just not sure on what brand those are. Probably Danner looking at those prices, Danner is a good brand __________________ 2x P3 1100's at 1400, Abit VP6, 2x Corsair 256mb PC150 sticks, 20gb 'cuda ATA-III, 2x 40gb 'cuda ATA-IV in raid 0. 20" Trinitron. No fans 2x 2400+ at 2288mhz (16.0 x 143), Iwill MPX2, 2x Kingmax PC-3200 256mb sticks, 4x 20gb 60gxp in Raid 5 on a Promise SX6000. Asus Ti4200 320/630. Cooled by Water

04-05-2002, 04:41 PM	#4
simplesid Cooling Neophyte Join Date: Mar 2002 Location: USA Posts: 18	... yes it is a danner pump... NB has mounting holes im useing a shuttle AK35GTR

04-05-2002, 04:58 PM	#5
mkosem Cooling Savant Join Date: May 2001 Location: here Posts: 494	my mobo(p4s333) and my vid card( aopen ti200) have the same mounting holes. --Matt __________________ If you can't cool it, blow it up!! http://www.mattkosem.com

04-05-2002, 10:05 AM	#2
DigitalChaos Cooling Savant Join Date: Jan 2002 Location: Waukesha, Wi Posts: 698	i have no idea BUT i have some info that may be of use: my friends Gainward GF3 heat sink... the pins on that did not fully reach the holes for the chipset on his Abit mobo... id say it was not more than 5mm smaller in reach.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)