DD gpu block...?

scythe · 07-10-2002, 07:30 PM

the newer one with the plex top and U channel , is this thing any good , and do you know if it will work with the gainward gf3 without having to take off the ramsinks. Anyone have it show some pics. Or anyone have any other recommendations for ones that will fit. Or ones that are decently priced and cover ram too.

Cyco-Dude · 07-10-2002, 07:33 PM

the new GPU WB from DDen is not available yet.

scythe · 07-10-2002, 07:41 PM

uhm... go look , the gf4 block yes it is , can get it from cooltechnica for 43$ and dangerden for 45$

Cyco-Dude · 07-10-2002, 07:58 PM

d0h! i was thinking of their new chipset block, my bad. i havent read anything about the new GPU block, so i dunno.

scythe · 07-10-2002, 08:45 PM

ahh well i ordered the block 12 feet of tygon and some epoxy incase ineed to saw some of my ramsinks

ikonis · 07-11-2002, 09:46 PM

tell me how it goes... i have a gainward gf3 and dont wanna replace the stock ramsinks as well

scythe · 07-13-2002, 01:31 AM

looks like im going to have to do something with them , got an email back from DD with a pic of a gf3 ti200 and the block and man those barbs run right over one of the memory chips , but i dont know how much different the ti200 is then my normal gf3 will have to see. HOPEFULLY the barbs actually touch the chip or are close , i can probaly sand down a penny and use it as a riser to transfer heat and just have the barbs cool a chip or so wont be like a total water cooling thing but should work somewhat

bdunosk · 07-27-2002, 08:32 PM

I removed the RAMsinks on my Gainward gf3 ti200 and the RAM actually works at a higher speed. Strange. :P

SonixOS · 07-27-2002, 10:02 PM

scythe, post that picture. I have a gf3 ti200 MSI 128mb joint. I wanna know if I can use that block.

scythe · 07-28-2002, 04:21 PM

no where to host , but the barbs go right over a ramchip i got my block what i did was took off the ramsink and i put them in a vice then just took these pliers like with little tongs on the end for cutting and tore out 3 fins where the barbs went through.

filed it down flat , put the sinks back on with artic alumina epoxy , and then it fit perfect

07-10-2002, 07:30 PM	#1
scythe Cooling Neophyte Join Date: Feb 2002 Location: fp , michigan Posts: 76	DD gpu block...? the newer one with the plex top and U channel , is this thing any good , and do you know if it will work with the gainward gf3 without having to take off the ramsinks. Anyone have it show some pics. Or anyone have any other recommendations for ones that will fit. Or ones that are decently priced and cover ram too. __________________ ...[-_-]... +-{ i }-+ ....[][].....

07-10-2002, 07:41 PM	#3
scythe Cooling Neophyte Join Date: Feb 2002 Location: fp , michigan Posts: 76	uhm... go look , the gf4 block yes it is , can get it from cooltechnica for 43$ and dangerden for 45$ __________________ ...[-_-]... +-{ i }-+ ....[][].....

07-10-2002, 08:45 PM	#5
scythe Cooling Neophyte Join Date: Feb 2002 Location: fp , michigan Posts: 76	ahh well i ordered the block 12 feet of tygon and some epoxy incase ineed to saw some of my ramsinks __________________ ...[-_-]... +-{ i }-+ ....[][].....

07-11-2002, 09:46 PM	#6
ikonis Cooling Neophyte Join Date: May 2002 Location: East Texas Posts: 14	tell me how it goes... i have a gainward gf3 and dont wanna replace the stock ramsinks as well Last edited by ikonis; 07-11-2002 at 09:50 PM.

07-13-2002, 01:31 AM	#7
scythe Cooling Neophyte Join Date: Feb 2002 Location: fp , michigan Posts: 76	looks like im going to have to do something with them , got an email back from DD with a pic of a gf3 ti200 and the block and man those barbs run right over one of the memory chips , but i dont know how much different the ti200 is then my normal gf3 will have to see. HOPEFULLY the barbs actually touch the chip or are close , i can probaly sand down a penny and use it as a riser to transfer heat and just have the barbs cool a chip or so wont be like a total water cooling thing but should work somewhat __________________ ...[-_-]... +-{ i }-+ ....[][].....

07-10-2002, 07:33 PM	#2
Cyco-Dude Cooling Savant Join Date: Feb 2002 Location: Dayton, Ohio Posts: 836	the new GPU WB from DDen is not available yet.

07-10-2002, 07:58 PM	#4
Cyco-Dude Cooling Savant Join Date: Feb 2002 Location: Dayton, Ohio Posts: 836	d0h! i was thinking of their new chipset block, my bad. i havent read anything about the new GPU block, so i dunno.

07-27-2002, 08:32 PM	#8
bdunosk Cooling Neophyte Join Date: May 2001 Location: Cincinnati, OH Posts: 93	I removed the RAMsinks on my Gainward gf3 ti200 and the RAM actually works at a higher speed. Strange. :P

07-27-2002, 10:02 PM	#9
SonixOS Cooling Savant Join Date: Mar 2002 Location: Silver Spring, MD Posts: 282	scythe, post that picture. I have a gf3 ti200 MSI 128mb joint. I wanna know if I can use that block. __________________ -sonix- ======================= Antec SX830 Abit KR7A-133 MSI Geforce3 Ti200 VT128 TV-IN and TV-OUT Sound Blaster Audigy Linksys LNE100 V2.0 Toshiba DVD Drive 40x/16x IBM Deskstar 60GXP 60gig Watercooled http://www.sonixnet.tk =======================

07-28-2002, 04:21 PM	#10
scythe Cooling Neophyte Join Date: Feb 2002 Location: fp , michigan Posts: 76	no where to host , but the barbs go right over a ramchip i got my block what i did was took off the ramsink and i put them in a vice then just took these pliers like with little tongs on the end for cutting and tore out 3 fins where the barbs went through. filed it down flat , put the sinks back on with artic alumina epoxy , and then it fit perfect __________________ ...[-_-]... +-{ i }-+ ....[][].....

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)