New Radiator Duct

JSimmons · 05-27-2003, 06:46 AM

Alrightie, after six days of work, I have finally finished the radiator duct section for my water-cooling setup.

This will be attached to the (inside) back of the YY Cube case with a pusher fan, and an external box housing a pulling fan.

Check out this over-engineered monstrosity:

http://www.paddedwall.org/watercool/wc_page3.html

jaydee · 05-28-2003, 01:45 PM

Looking good, nice documentation on it!

JSimmons · 05-28-2003, 03:40 PM

I improved the write-up. There's still some touch-up left to do, and I have to take some more pics, but it's coming along.

I will have more new pics later this evening.

Giblet Plus! · 05-28-2003, 07:02 PM

I like Plan D!

JSimmons · 05-29-2003, 06:45 AM

I added some pics of the rhomboid, the external fan plenum, and the drivebay section.

MadDogMe · 05-30-2003, 03:51 AM

That's very nicely made (plan D), the copper would have been if you'd done it like the alu in individual sheets coupled with angle alu or Cu so it did'nt bow...

I thought a plenum chamber was when there are 'fins' inside to channel the airflow over the entire area of the target(radiator)?, otherwise it's a plain duct?...

JSimmons · 05-30-2003, 07:37 AM

"Plenum" sounds fancier than "box" or "duct".

05-27-2003, 06:46 AM	#1
JSimmons Cooling Savant Join Date: Apr 2003 Location: 4-sided room with an exit going east, and an exit going south Posts: 392	New Radiator Duct Alrightie, after six days of work, I have finally finished the radiator duct section for my water-cooling setup. This will be attached to the (inside) back of the YY Cube case with a pusher fan, and an external box housing a pulling fan. Check out this over-engineered monstrosity: http://www.paddedwall.org/watercool/wc_page3.html __________________ My Watercooling Stuff Last edited by JSimmons; 05-27-2003 at 08:46 AM.

05-28-2003, 03:40 PM	#3
JSimmons Cooling Savant Join Date: Apr 2003 Location: 4-sided room with an exit going east, and an exit going south Posts: 392	I improved the write-up. There's still some touch-up left to do, and I have to take some more pics, but it's coming along. I will have more new pics later this evening. __________________ My Watercooling Stuff

05-29-2003, 06:45 AM	#5
JSimmons Cooling Savant Join Date: Apr 2003 Location: 4-sided room with an exit going east, and an exit going south Posts: 392	I added some pics of the rhomboid, the external fan plenum, and the drivebay section. __________________ My Watercooling Stuff

05-30-2003, 07:37 AM	#7
JSimmons Cooling Savant Join Date: Apr 2003 Location: 4-sided room with an exit going east, and an exit going south Posts: 392	"Plenum" sounds fancier than "box" or "duct". __________________ My Watercooling Stuff

05-28-2003, 01:45 PM	#2
jaydee Put up or Shut Up Join Date: Dec 2001 Location: Spokane WA Posts: 6,506	Looking good, nice documentation on it!

05-28-2003, 07:02 PM	#4
Giblet Plus! Cooling Neophyte Join Date: Dec 2002 Location: Victoria, MN Posts: 23	I like Plan D!

05-30-2003, 03:51 AM	#6
MadDogMe Thermophile Join Date: Aug 2002 Location: Just shut up ;) ... Posts: 1,068	That's very nicely made (plan D), the copper would have been if you'd done it like the alu in individual sheets coupled with angle alu or Cu so it did'nt bow... I thought a plenum chamber was when there are 'fins' inside to channel the airflow over the entire area of the target(radiator)?, otherwise it's a plain duct?...

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)