Sucky temps

OcPunK · 10-17-2001, 06:16 AM

Running Prime95 right now my temp is 150F/66C! Tbird 1.33@1.466.71MHz @2.19Vs

My cooling loop Rio 200 Submerged in a small resivor then it pumps into the heatercore the heatercore is has two 100CFM panaflows one ducked on the front blowing in and the other ducked on the back sucking air out. After the water goes through the heatercore it goes into the maze2 block that is connected to the Tbird by a thin layer of AS2. After the block it goes back the res, all tubing is 3/8". Ok so what is the problem with the loop? I reseated the Maze2 so thats not it. Does flowrate really matter that much? Una had a super low flow setup and his cooling didnt inprove when switching to a high flow 1/2" tubing. Could it be that this heatercore just sucks? help me

LiquidCool · 10-17-2001, 06:30 AM

I'd say it's the low flow plus your voltage! Rio200 flows like 135gph which for that big heater core isnt enough.

The bigger your radiator, the faster you can flow, the cooler you'll get.

OcPunK · 10-17-2001, 06:58 AM

!!!138F/59C MAX LOAD!!!
heh 4th time worked! I reseated the maze2 for the 4th time did the same thing where I clean all the AS2 off and put on a thin layer, well this time I guess I got it right!

I'm still going to get a danner pump and see if it lowers it more. Now to overclock this ayhja.

Sled_Dog · 10-17-2001, 08:40 AM

Quote:

Originally posted by OcPunK:
!!!138F/59C MAX LOAD!!!
heh 4th time worked! I reseated the maze2 for the 4th time did the same thing where I clean all the AS2 off and put on a thin layer, well this time I guess I got it right! I'm still going to get a danner pump and see if it lowers it more. Now to overclock this ayhja.

You need a shim you can't mount that block for your life. Matt = teh stupid

OcPunK · 10-17-2001, 09:47 AM

no I think its the posts placement bc remeber I had those on there from the maze1 hold down

OcPunK · 10-17-2001, 09:48 AM

oh anyway you have to go to school hahahahhahahahh!Hahaahahahahahahaahha!!!

Sled_Dog · 10-19-2001, 03:47 PM

your still dumb and can't mount a maze 2 to save your life.

Kevin · 10-19-2001, 04:43 PM

Quote:

Originally posted by Sled_Dog:
your still dumb and can't mount a maze 2 to save your life.

Play nice... Then again, what do I know i'm just "drunk ass or college student Kev" heheheh

-Kev

UnaClocker · 10-19-2001, 09:24 PM

Try using more AS paste.. I found that the "ultra thin" layer everyone talks about isn't as thin as it sounds. When I first started using AS, I put it on uber thin, my temps sucked. So I put it on normally, and my temps improved immensly.

10-17-2001, 06:16 AM	#1
OcPunK Cooling Savant Join Date: Jun 2001 Location: Under ground cave in PA to keep PCs cool! Posts: 125	Sucky temps Running Prime95 right now my temp is 150F/66C! Tbird 1.33@1.466.71MHz @2.19Vs My cooling loop Rio 200 Submerged in a small resivor then it pumps into the heatercore the heatercore is has two 100CFM panaflows one ducked on the front blowing in and the other ducked on the back sucking air out. After the water goes through the heatercore it goes into the maze2 block that is connected to the Tbird by a thin layer of AS2. After the block it goes back the res, all tubing is 3/8". Ok so what is the problem with the loop? I reseated the Maze2 so thats not it. Does flowrate really matter that much? Una had a super low flow setup and his cooling didnt inprove when switching to a high flow 1/2" tubing. Could it be that this heatercore just sucks? help me __________________ www.1337info.com

10-17-2001, 06:58 AM	#3
OcPunK Cooling Savant Join Date: Jun 2001 Location: Under ground cave in PA to keep PCs cool! Posts: 125	!!!138F/59C MAX LOAD!!! heh 4th time worked! I reseated the maze2 for the 4th time did the same thing where I clean all the AS2 off and put on a thin layer, well this time I guess I got it right! I'm still going to get a danner pump and see if it lowers it more. Now to overclock this ayhja. __________________ www.1337info.com

10-17-2001, 09:47 AM	#5
OcPunK Cooling Savant Join Date: Jun 2001 Location: Under ground cave in PA to keep PCs cool! Posts: 125	no I think its the posts placement bc remeber I had those on there from the maze1 hold down __________________ www.1337info.com

10-17-2001, 09:48 AM	#6
OcPunK Cooling Savant Join Date: Jun 2001 Location: Under ground cave in PA to keep PCs cool! Posts: 125	oh anyway you have to go to school hahahahhahahahh!Hahaahahahahahahaahha!!! __________________ www.1337info.com

10-19-2001, 03:47 PM	#7
Sled_Dog Cooling Savant Join Date: Jul 2001 Location: Snowyland(not Alaska) Posts: 238	your still dumb and can't mount a maze 2 to save your life. __________________ pro/chat has a website now? wow

10-17-2001, 06:30 AM	#2
LiquidCool Cooling Savant Join Date: Apr 2001 Location: Central Florida Posts: 231	I'd say it's the low flow plus your voltage! Rio200 flows like 135gph which for that big heater core isnt enough. The bigger your radiator, the faster you can flow, the cooler you'll get.

10-19-2001, 09:24 PM	#9
UnaClocker Cooling Savant Join Date: Apr 2000 Location: Bremerton, WA Posts: 514	Try using more AS paste.. I found that the "ultra thin" layer everyone talks about isn't as thin as it sounds. When I first started using AS, I put it on uber thin, my temps sucked. So I put it on normally, and my temps improved immensly. __________________ The UnaClocker Watercooler Extraordinaire! Overclock till it goes BOOM!

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)