Water Temp Problem Please Advise

Icemanzero · 02-18-2001, 12:27 AM

I need some advise I have a 1gig T-bird @ 1250 @ 1.80v with a 118W Pelt on a separate PS. I have a Swiftech water block & Cooper cold plate. (Great product I must add!)also I use Artic silver. I have Leufken's Alum. tank with inline pump and that 4x4 plate Radiator that every knows about w/ 2 92mm Sanyo/denki 55CFM fans on it. One blowing cool air across it, and the other sucking it out. Heres the prob. When I first start up and the water is @ amb. the backside of the chip is right around 18F @ idle and under full load gets around 50F but after 2 or so hours the heat builds up in the tank as high as 103F when the system temp is only about 80F! Seems as if I just cant get this damn water cool no matter what I do and its pissing me off!! any advice would be very well received and you can ICQ me even, if you would like. 24964100 Thanks in advance. -Ice

Kevin · 02-18-2001, 06:16 PM

You are using that radiator in a blowhole-style way... right?

Kevin · 02-18-2001, 06:18 PM

Woah... I re-read the post. Didn't see the whole thing about a peltier w/ a high wattage TEC. Okay... You are going to need better cooling than just a 4x4 radiator. We need to think of a better way to cool that water. How much room do you have in your case and what kind of case is it?

Icemanzero · 02-18-2001, 08:55 PM

Yes the radiator Fans are setup with blow holes and and are vented out. My case is an Enlight EN-8900. Its a big full server type tower, has two PS's, but with everything being self-contained and fans and all,its getting a bit cramped for space. So what would you suggest?

[This message has been edited by Icemanzero (edited 02-18-2001).]

Icemanzero · 02-18-2001, 09:05 PM

I forgot to add, from the water block it flows to the 4X4 stacked plate rad. then it goes into a Alum. Water block with a 50W TEC with a GlobalWin HS+Fan on it to try and knock the temp down a little before it goes into the Alum. tank which has fans blowing on it also.

SYX · 02-18-2001, 09:26 PM

This is kinda little in this case, but I dunno what some people are thinking. You want coldest water to go on waterblock so it takes in as much heat as possible... putting radiator after waterblock is a small minus because water will get heat from aluminum tank where there is more idle warm water and go to the water block.

Also for full tower case I strongly suggest cooling cube from dangerden.

02-18-2001, 12:27 AM	#1
Icemanzero Cooling Neophyte Join Date: Jan 2001 Location: Dallas, TX USA Posts: 15	Water Temp Problem Please Advise I need some advise I have a 1gig T-bird @ 1250 @ 1.80v with a 118W Pelt on a separate PS. I have a Swiftech water block & Cooper cold plate. (Great product I must add!)also I use Artic silver. I have Leufken's Alum. tank with inline pump and that 4x4 plate Radiator that every knows about w/ 2 92mm Sanyo/denki 55CFM fans on it. One blowing cool air across it, and the other sucking it out. Heres the prob. When I first start up and the water is @ amb. the backside of the chip is right around 18F @ idle and under full load gets around 50F but after 2 or so hours the heat builds up in the tank as high as 103F when the system temp is only about 80F! Seems as if I just cant get this damn water cool no matter what I do and its pissing me off!! any advice would be very well received and you can ICQ me even, if you would like. 24964100 Thanks in advance. -Ice

02-18-2001, 06:16 PM	#2
Kevin Slacking more than your weird uncle Join Date: Nov 2000 Location: San Diego, CA (UCSD) / Los Angeles, CA (home) Posts: 1,605	You are using that radiator in a blowhole-style way... right?

02-18-2001, 06:18 PM	#3
Kevin Slacking more than your weird uncle Join Date: Nov 2000 Location: San Diego, CA (UCSD) / Los Angeles, CA (home) Posts: 1,605	Woah... I re-read the post. Didn't see the whole thing about a peltier w/ a high wattage TEC. Okay... You are going to need better cooling than just a 4x4 radiator. We need to think of a better way to cool that water. How much room do you have in your case and what kind of case is it?

02-18-2001, 08:55 PM	#4
Icemanzero Cooling Neophyte Join Date: Jan 2001 Location: Dallas, TX USA Posts: 15	Yes the radiator Fans are setup with blow holes and and are vented out. My case is an Enlight EN-8900. Its a big full server type tower, has two PS's, but with everything being self-contained and fans and all,its getting a bit cramped for space. So what would you suggest? [This message has been edited by Icemanzero (edited 02-18-2001).]

02-18-2001, 09:05 PM	#5
Icemanzero Cooling Neophyte Join Date: Jan 2001 Location: Dallas, TX USA Posts: 15	I forgot to add, from the water block it flows to the 4X4 stacked plate rad. then it goes into a Alum. Water block with a 50W TEC with a GlobalWin HS+Fan on it to try and knock the temp down a little before it goes into the Alum. tank which has fans blowing on it also.

02-18-2001, 09:26 PM	#6
SYX Cooling Neophyte Join Date: Jan 2001 Posts: 35	This is kinda little in this case, but I dunno what some people are thinking. You want coldest water to go on waterblock so it takes in as much heat as possible... putting radiator after waterblock is a small minus because water will get heat from aluminum tank where there is more idle warm water and go to the water block. Also for full tower case I strongly suggest cooling cube from dangerden.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)