How do you stack peltiers?

Squishyface · 02-22-2001, 01:08 AM

Obviously, its like legoes, you just put one on top of the other :P hehe
Well...do you want the weaker of the two on the cpu with the higher wattage pelt cooling the smaller pelt?...because more heat has to be removed each step? or the other way around?
if i'm gonna do this watercooling thing...might as well go all out, since pelts are cheap :P hehe

------------------
1.2Tbird @1352 air cooled. Soon to be watercooled :P

Joe · 02-22-2001, 08:41 AM

Don't stack a pelt... not good, and very inefficient.

------------------
C-ya
Joe - Owner/Editor
www.ProCooling.com
Where the Completely Addicted Come to Cool Off

Somebody set up us the bomb.

Freakyfrank · 02-24-2001, 09:29 AM

2 stages can be done..
but only if you're interested in a higher Tdelta than 55C..
since the efficiency of TEC's are already low, you're dealing with a efficiency of a efficiency in a 2-stage setup.

you'd better use 2 TEC's next to each other, doubling the potential.

------------------
OC'ing is my middlename

Joe · 02-24-2001, 12:22 PM

Stacking for all intents and purposes is dangerous, and a waste.

one pelt dies and you could be looking at a fire risk ( the 2nd one.. between the block and the first pelt.)

------------------
C-ya
Joe - Owner/Editor
www.ProCooling.com
Where the Completely Addicted Come to Cool Off

Somebody set up us the bomb.

Rich W · 02-24-2001, 03:38 PM

Actually, pelts conduct heat rather well, as long as they aren't driving an electrical load... check out the Seabach effect (opposite of Peltier effect). It is used on deep space probes, and when is use (I think, back then) was like 3% efficient.

02-22-2001, 01:08 AM	#1
Squishyface Cooling Neophyte Join Date: Feb 2001 Location: columbus, Ohio, USA Posts: 54	How do you stack peltiers? Obviously, its like legoes, you just put one on top of the other :P hehe Well...do you want the weaker of the two on the cpu with the higher wattage pelt cooling the smaller pelt?...because more heat has to be removed each step? or the other way around? if i'm gonna do this watercooling thing...might as well go all out, since pelts are cheap :P hehe ------------------ 1.2Tbird @1352 air cooled. Soon to be watercooled :P

02-22-2001, 08:41 AM	#2
Joe The Pro/Life Support System Join Date: Dec 1999 Location: Denver, CO Posts: 4,041	Don't stack a pelt... not good, and very inefficient. ------------------ C-ya Joe - Owner/Editor www.ProCooling.com Where the Completely Addicted Come to Cool Off Somebody set up us the bomb.

02-24-2001, 09:29 AM	#3
Freakyfrank Cooling Savant Join Date: Nov 2000 Location: Eindhoven, Holland Posts: 238	2 stages can be done.. but only if you're interested in a higher Tdelta than 55C.. since the efficiency of TEC's are already low, you're dealing with a efficiency of a efficiency in a 2-stage setup. you'd better use 2 TEC's next to each other, doubling the potential. ------------------ OC'ing is my middlename

02-24-2001, 12:22 PM	#4
Joe The Pro/Life Support System Join Date: Dec 1999 Location: Denver, CO Posts: 4,041	Stacking for all intents and purposes is dangerous, and a waste. one pelt dies and you could be looking at a fire risk ( the 2nd one.. between the block and the first pelt.) ------------------ C-ya Joe - Owner/Editor www.ProCooling.com Where the Completely Addicted Come to Cool Off Somebody set up us the bomb.

02-24-2001, 03:38 PM	#5
Rich W Cooling Neophyte Join Date: Feb 2000 Posts: 77	Actually, pelts conduct heat rather well, as long as they aren't driving an electrical load... check out the Seabach effect (opposite of Peltier effect). It is used on deep space probes, and when is use (I think, back then) was like 3% efficient.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)