The Lemon Block Cu - Page 2

Yo-DUH_87 · 08-08-2003, 01:44 AM

Nice block design, and the improvement over the Maze 4 is nothing to sneaze at either

Do you think this block would be any good for pelts?

jaydee · 08-08-2003, 09:07 AM

Not making any for anyone else.

Yes, it would be very good for pelts.

AXDA2600DKV3D · 08-09-2003, 04:01 AM

i know u said youre not making it for anyone else but i am now trying to get a cascade off of cathar

mind makin me one to compare and review?

:shrug: :shrug:

jaydee · 08-12-2003, 09:33 AM

Quote:

Originally posted by AXDA2600DKV3D
i know u said youre not making it for anyone else but i am now trying to get a cascade off of cathar

mind makin me one to compare and review?
:shrug: :shrug:

Only if you have Bill Adams level of testing equipment and knowlege. Otherwise it isn't worth the time it takes to make another on my little mill.

AXDA2600DKV3D · 08-12-2003, 09:44 AM

Quote:

Only if you have Bill Adams level of testing equipment and knowlege.

which i do? (pretends)

jaydee · 08-21-2003, 10:26 AM

Was finally able to resore the pics. Changed Domain names right before I got banned so I couldn't edit the urls to the pics.

AXDA2600DKV3D · 08-21-2003, 10:38 AM

why were u banned?

jaydee · 08-21-2003, 11:04 AM

Quote:

Originally posted by AXDA2600DKV3D
why were u banned?

For being an ass, I deserved it. See my Direct Die Cooling thread I just started.

Blackeagle · 08-22-2003, 05:41 PM

JayDee,

As long as you intend to make a couple more of the Lemon copper blocks for your new set up of multi water cooled systems anyway.......

Any chance you'll make use of that roughing end mill and perhaps a few other tweaks? Should not increase the time to machine to much to drill a dimple pattern and use the roughing mill. Or to change the central inlet to a differant diamiter to increase velocity of the water intering the blocks.

And would offer interesting insight into how much farther this design can go. Not to mention it would provide better cooling then for your system it will in time be in.

jaydee · 08-22-2003, 05:55 PM

Quote:

Originally posted by Blackeagle
JayDee,

As long as you intend to make a couple more of the Lemon copper blocks for your new set up of multi water cooled systems anyway.......

Any chance you'll make use of that roughing end mill and perhaps a few other tweaks? Should not increase the time to machine to much to drill a dimple pattern and use the roughing mill. Or to change the central inlet to a differant diamiter to increase velocity of the water intering the blocks.

And would offer interesting insight into how much farther this design can go. Not to mention it would provide better cooling then for your system it will in time be in.

I am actually re-designing it. Will be a while before anything gets done on the next version. Spent this and next month play money already on computer parts.

One of which was a GF4 440MX with mounting holes and a Asus A7V8X-X with NB mounting holes. This will be the start of my poor mans gaming rig project. The GPU and NB blocks will be smaller versions of the re-designed Lemon Block. Going to stuff it all in my Antec SX-830.

Also the Multi computer project is still on to. Not going to use the newer lemon Block though. Will use the one I already have, the DD Maze 4 and another that is in the design phase.

Blackeagle · 08-22-2003, 09:26 PM

Ahhh. Will look forward to seeing the new design!

And this will give you another folder, at least part time. Kool!

jaydee · 10-28-2003, 12:35 PM

Quote:

Originally posted by Blackeagle
Ahhh. Will look forward to seeing the new design!

And this will give you another folder, at least part time. Kool!

Here is the second one in development. http://forums.procooling.com/vbb/sho...2677#post92677

08-08-2003, 01:44 AM	#26
Yo-DUH_87 Cooling Savant Join Date: Mar 2002 Location: Oregon, USA Posts: 230	Nice block design, and the improvement over the Maze 4 is nothing to sneaze at either Do you think this block would be any good for pelts? __________________ Signing out... Yo-DUH_87 If it works, fix it until it's broke! Then, after it's broke, add duct tape! Affordable webhosting!

08-08-2003, 09:07 AM	#27
jaydee Put up or Shut Up Join Date: Dec 2001 Location: Spokane WA Posts: 6,506	Not making any for anyone else. Yes, it would be very good for pelts.

08-09-2003, 04:01 AM	#28
AXDA2600DKV3D Cooling Neophyte Join Date: Aug 2003 Location: Florida, USA Posts: 40	i know u said youre not making it for anyone else but i am now trying to get a cascade off of cathar mind makin me one to compare and review? :shrug: :shrug:

08-21-2003, 10:26 AM	#31
jaydee Put up or Shut Up Join Date: Dec 2001 Location: Spokane WA Posts: 6,506	Was finally able to resore the pics. Changed Domain names right before I got banned so I couldn't edit the urls to the pics.

08-21-2003, 10:38 AM	#32
AXDA2600DKV3D Cooling Neophyte Join Date: Aug 2003 Location: Florida, USA Posts: 40	why were u banned?

08-22-2003, 05:41 PM	#34
Blackeagle Thermophile Join Date: Oct 2002 Location: U.S.A = Michigan Posts: 1,243	JayDee, As long as you intend to make a couple more of the Lemon copper blocks for your new set up of multi water cooled systems anyway....... Any chance you'll make use of that roughing end mill and perhaps a few other tweaks? Should not increase the time to machine to much to drill a dimple pattern and use the roughing mill. Or to change the central inlet to a differant diamiter to increase velocity of the water intering the blocks. And would offer interesting insight into how much farther this design can go. Not to mention it would provide better cooling then for your system it will in time be in.

08-22-2003, 09:26 PM	#36
Blackeagle Thermophile Join Date: Oct 2002 Location: U.S.A = Michigan Posts: 1,243	Ahhh. Will look forward to seeing the new design! And this will give you another folder, at least part time. Kool!

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)