Go Back   Pro/Forums > ProCooling Technical Discussions > Snap Server / NAS / Storage Technical Goodies
Password
Register FAQ Members List Calendar Chat

Snap Server / NAS / Storage Technical Goodies The Home for Snap Server Hacking, Storage and NAS info. And NAS / Snap Classifides

Closed Thread
Thread Tools
Unread 01-16-2007, 01:53 PM   #1
blue68f100
Thermophile
 
blue68f100's Avatar
 
Join Date: Jul 2005
Location: Plano, TX
Posts: 3,135
Attention All 4100 owners

There has been some unexplained errors on 4100’s models after HD’s were upgraded. Further investigations show that a modification/repair was made to the original MB, ASSY# 707150048-001. The area of repair/modification was made to 2 areas FB1 & FB2.

FB1 is located between the two Promise Controller. The second area FB2 that has the same repair left of the left promise chip. This one (FB2) points toward the IDE cables.

If you have a ASSY # 70715048-001 or 003 look at the photos below and see if you are affected. 003 seams to be the repaired boards. But so far I have found 1 (-003) that has not been repaired. So you will have to look on the board for the repairs. Now some of the repairs have been done differently than the photo posted. If you are not sure post a photo of the area in question.

This is a -001 board that has NOT been repaired.


This is the 003 board showing locations of both area.


Below are pictures of a 003 A board that has been repaired.

FB1 area.

FB2 area

Notice that 1 component has been replaced with 2 and are bridged together with solder.

For more info please post your questions.
Attached Images
File Type: jpg P1160147-0.JPG (65.8 KB, 556 views)
File Type: jpg P1160147-3.JPG (52.8 KB, 511 views)
File Type: jpg P1160175-2 2 boxes.JPG (80.6 KB, 489 views)
File Type: jpg P1160175-FB2 area.JPG (99.3 KB, 479 views)
File Type: jpg This Area with block.JPG (41.0 KB, 487 views)
__________________
1 Snap 4500 - 1.0T (4 x 250gig WD2500SB RE), Raid5,
1 Snap 4500 - 1.6T (4 x 400gig Seagates), Raid5,
1 Snap 4200 - 4.0T (4 x 2gig Seagates), Raid5, Using SATA converts from Andy

Link to SnapOS FAQ's http://forums.procooling.com/vbb/showthread.php?t=13820

Last edited by blue68f100; 02-02-2007 at 07:47 AM. Reason: Found 2 areas of repair
blue68f100 is offline  
Unread 01-16-2007, 02:22 PM   #2
jontz
Cooling Savant
 
Join Date: Feb 2006
Location: South Bend, IN
Posts: 385
Default Re: Attention All 4100 owners

What exactly does this repair do? It appears from the pictures that you have added a second resistor in parallel, thus halving the resistance (assuming it is a resistor of the same value). Is that the case?

And yes, I am finally back...CRAZY around here for several months, but I survived
__________________
Snap Server 4100, 4x120GB Seagate Drives, RAID 5, version 3.4.803
jontz is offline  
Unread 01-16-2007, 02:46 PM   #3
blue68f100
Thermophile
 
blue68f100's Avatar
 
Join Date: Jul 2005
Location: Plano, TX
Posts: 3,135
Default Re: Attention All 4100 owners

Without this repair your Raid Array will be unstable, data may be in trouble. It only seam to affect the smaller capacity units that have been upgraded. Don't know how may are affected. The 001 board is a 120gig model. The 003 is a 240gig.
__________________
1 Snap 4500 - 1.0T (4 x 250gig WD2500SB RE), Raid5,
1 Snap 4500 - 1.6T (4 x 400gig Seagates), Raid5,
1 Snap 4200 - 4.0T (4 x 2gig Seagates), Raid5, Using SATA converts from Andy

Link to SnapOS FAQ's http://forums.procooling.com/vbb/showthread.php?t=13820
blue68f100 is offline  
Unread 01-17-2007, 06:26 AM   #4
Hallis
Cooling Savant
 
Hallis's Avatar
 
Join Date: Oct 2001
Location: Dallas, Tx
Posts: 469
Default Re: Attention All 4100 owners

Now that is good info, if somebody were good at surface soldering you could repair your own.
__________________
Snap Servers:

1100 - 1x300gb Seagate Baracuda (SnapOS Version 3.4.807)
2200 - 2x80gb Maxtor (one dead) (SnapOS 4.0.860)
Hallis is offline  
Unread 01-17-2007, 07:31 AM   #5
rpmurray
Cooling Savant
 
Join Date: Apr 2006
Location: Tennessee
Posts: 157
Default Re: Attention All 4100 owners

Quote:
Originally Posted by blue68f100
Without this repair your Raid Array will be unstable, data may be in trouble. It only seam to affect the smaller capacity units that have been upgraded. Don't know how may are affected. The 001 board is a 120gig model. The 003 is a 240gig.
Any specific error messages that display in the logs?
rpmurray is offline  
Unread 01-17-2007, 07:58 AM   #6
blue68f100
Thermophile
 
blue68f100's Avatar
 
Join Date: Jul 2005
Location: Plano, TX
Posts: 3,135
Default Re: Attention All 4100 owners

One of the errors are constant disk checks and resync on restarts. Unless you reboot you may not notice you have problem, then it's to late. Just pop the top and see if yours MB is a 003, if so the mod has likely already been done. If it's a 001 you will need to look closely. Some have and others not. The 001 board was a 120gig (4 x 30gig), did not have the fix. The 003 was a 240gig (4 x 60gig) had the repair. I have not had the chance to look at other models to see if its just the 120gig (and maybe 240 gig) model effected.

This problem only show up after you upgrade the HD, on 120 models. I do not have enough info to know if other models are effected. So far all of the models 240gig and greater that I have seen, has had the mod (003 boards).
__________________
1 Snap 4500 - 1.0T (4 x 250gig WD2500SB RE), Raid5,
1 Snap 4500 - 1.6T (4 x 400gig Seagates), Raid5,
1 Snap 4200 - 4.0T (4 x 2gig Seagates), Raid5, Using SATA converts from Andy

Link to SnapOS FAQ's http://forums.procooling.com/vbb/showthread.php?t=13820

Last edited by blue68f100; 01-17-2007 at 08:08 AM.
blue68f100 is offline  
Unread 01-18-2007, 07:23 PM   #7
blue68f100
Thermophile
 
blue68f100's Avatar
 
Join Date: Jul 2005
Location: Plano, TX
Posts: 3,135
Default Re: Attention All 4100 owners

Updated post original post.

Found a second area (FB2) of repair, done the same way, with what apears to be the same componets. It is located to the left of the Promise Chip. Will update the photo showing the areas.

The resistor measures 10 ohm
__________________
1 Snap 4500 - 1.0T (4 x 250gig WD2500SB RE), Raid5,
1 Snap 4500 - 1.6T (4 x 400gig Seagates), Raid5,
1 Snap 4200 - 4.0T (4 x 2gig Seagates), Raid5, Using SATA converts from Andy

Link to SnapOS FAQ's http://forums.procooling.com/vbb/showthread.php?t=13820

Last edited by blue68f100; 01-18-2007 at 08:53 PM.
blue68f100 is offline  
Unread 01-19-2007, 10:34 PM   #8
sunfriek
Cooling Neophyte
 
Join Date: Jan 2007
Location: West coast
Posts: 1
Default Re: Attention All 4100 owners

on my Dell 705n(snap 4100) its board is 70715048-006 which has this mod applied..

mine is 60Gx4 via Seagate barracuda ATA IV (st360021a) 240G.

best regards
sunfriek is offline  
Unread 01-26-2007, 11:10 PM   #9
bsmith
Cooling Neophyte
 
Join Date: Jan 2007
Location: SC
Posts: 2
Default Re: Attention All 4100 owners

Not to ask a stupid question but, what point is there in adding a resister in series with a ferrite bead. Generally an smt ferrite bead has a dc resistance in the tenths of an ohm. I could see maybe adding a small cap to it to further block unwanted frequencies. BTW I have a 4100 70715048-001 without the mods.I suppose I will try and find a couple of 10ohm SMT resistors in my stash and add them as I'm getting ready to go to 4x160G from 4x30G
bsmith is offline  
Unread 01-27-2007, 12:23 AM   #10
wgong
Cooling Neophyte
 
Join Date: Nov 2006
Location: Wollongong NSW Australia
Posts: 16
Default Re: Attention All 4100 owners

Quote:
Originally Posted by sunfriek
on my Dell 705n(snap 4100) its board is 70715048-006 which has this mod applied..
My 705N also has both mods - it is even newer (70715048-007). It was also a 240GB unit.

P.S. I cannot enter my 705N Service Tag into Dell's support page. I suspect it is because the original unit failed and was replaced under warranty and no one updated the database to reflect the new number.
__________________
Dell 705N v3.4.790 4x Seagate 7200 160GB
wgong is offline  
Unread 02-15-2007, 07:49 AM   #11
blue68f100
Thermophile
 
blue68f100's Avatar
 
Join Date: Jul 2005
Location: Plano, TX
Posts: 3,135
Default Re: Attention All 4100 owners

Quote:
Originally Posted by bsmith
Not to ask a stupid question but, what point is there in adding a resister in series with a ferrite bead. Generally an smt ferrite bead has a dc resistance in the tenths of an ohm. I could see maybe adding a small cap to it to further block unwanted frequencies. BTW I have a 4100 70715048-001 without the mods.I suppose I will try and find a couple of 10ohm SMT resistors in my stash and add them as I'm getting ready to go to 4x160G from 4x30G
Will try to explain why it is needed. The resister is used to slow the response of the coils or damper them. Apparently with larger drives it was not settelting down. Like they were over driving the coils. Causing scatter, which in turns corrupts the raid5 array.

Recovery is very difficult in this condition because the drives are not put the data on the disk where it is suppose to be.

When you are trying to sync 4 drives timing is critical. Even a drive reallocating a bad sector with smart tech can cause problems. It best if you can run a utility to check the surface and have it update the table prior or soon after put in service. This way most of the bad sectors will not be use.
__________________
1 Snap 4500 - 1.0T (4 x 250gig WD2500SB RE), Raid5,
1 Snap 4500 - 1.6T (4 x 400gig Seagates), Raid5,
1 Snap 4200 - 4.0T (4 x 2gig Seagates), Raid5, Using SATA converts from Andy

Link to SnapOS FAQ's http://forums.procooling.com/vbb/showthread.php?t=13820
blue68f100 is offline  
Unread 04-01-2007, 08:02 PM   #12
bn2000
Cooling Neophyte
 
Join Date: Apr 2007
Location: Germany
Posts: 1
Default Re: Attention All 4100 owners

Mentioned repairs can also be found on MB 70715048-005A.

Nevertheless heavy problems with Snap4100 upgraded from 4x40GB to 4x160GB (4x130GB matched).

System hangs on W2KSP4 while transfering hugh amounts of data to Snap and results in manual reboot by reset button.

Is there any idea ?

System configuration is:
SnapOS V3.0.566
Bios V2.4.437
Hardware V2.2.1
bn2000 is offline  
Unread 04-02-2007, 06:51 AM   #13
blue68f100
Thermophile
 
blue68f100's Avatar
 
Join Date: Jul 2005
Location: Plano, TX
Posts: 3,135
Default Re: Attention All 4100 owners

Please repost on a different thread. I'm trying to keep this one strictly for MB mods.
__________________
1 Snap 4500 - 1.0T (4 x 250gig WD2500SB RE), Raid5,
1 Snap 4500 - 1.6T (4 x 400gig Seagates), Raid5,
1 Snap 4200 - 4.0T (4 x 2gig Seagates), Raid5, Using SATA converts from Andy

Link to SnapOS FAQ's http://forums.procooling.com/vbb/showthread.php?t=13820
blue68f100 is offline  
Closed Thread


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 06:42 PM.


Powered by vBulletin® Version 3.7.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(C) 2005 ProCooling.com
If we in some way offend you, insult you or your people, screw your mom, beat up your dad, or poop on your porch... we're sorry... we were probably really drunk...
Oh and dont steal our content bitches! Don't give us a reason to pee in your open car window this summer...