Re: "Nazca" - Waterblock Concept
 

Yeah, the image of the base after fixing the perimeter was lacking the cups.
http://www.captainslug.com/modding/mcp-block_9999.jpg
They're 1/16th" deep and I will be making them with a modified milling bit so that the bottom edges will be rounded and a cone will be left in the center.
I will probably need to epoxy the capillary tubes in place. The material of the disc itself isn't terribly important but I need something that's rigid enough at 1/16th" thickness and I will have to drill 52 holes into it using a programmable mill.
Brass would be fine, I would prefer Delrin though. What would respond best to epoxy with stainless steel?

Re: "Nazca" - Waterblock Concept
 

Why dont you get some brass tube? You could possibly solder that into place.
Brass would be best for epoxying the tubes in I think.
I doubt you'll be able to turn those little tiny peices of tube down to a smaller diameter.

I know you wont make that 52 holes that size in stainless, it wouldnt be fun!

and the bottoms of those cups, leave them flat, you dont want to help the water get out of there, you want the most turblience.

Jon

Re: "Nazca" - Waterblock Concept
 

Oddly enough it comes in the same size. I didn't think it did.
Would it be better to get brass rod that's 3/64 OD then drill our the center or get 1/16" OD tubing and then sand the outside down to 3/64?
If only I could remember what my uncle taught me about casting brass cartridge shells...

I was thinking it would be easier to put the pieces in a drill press and use sandpaper or a sanding stone to reduce the outer diameter where I need to.

Re: "Nazca" - Waterblock Concept
 

Probably putting them in a lathe rather than drill press would be better, but if I had a choice I think I'd be inclined to buy smaller OD rod and drill out the center.

Re: "Nazca" - Waterblock Concept
 

the base of the cup holes needs to flat smooth and square. Putting a cone in the middle will lower performance and putting a radius on the edge in this case is not a good idea (this is counter to normal design principals.)

I'll try this weekend and write up something in the wiki about jet impingement and how it works but these days i dont seem to have the time for things like that so i make no promises and whatever i have time for this weekend is going to be very bried and probably a bit crap.

Key thing to remember is that the spacing of the plate and the nozzle exit is exceptionally important and given you nozzle size is going to be very small i have concerns about the construction. I would think the MAX you would want to make it is 3 times the nozzle diameter so good luck! Above about 9 to 15 times and its not jet impingement. The walls of the holes need not be that deep but it requires some serious number crunching and fluid mech knowledge to know what "not that big" means. The characteristic length scale is the nozzle exit diameter so maybe 10 times that is a good guess.

Re: "Nazca" - Waterblock Concept
 

Alright. Looks like brass rod will be easiest and will allow me to get these dimensions for each cup.
http://www.captainslug.com/modding/mcp-block_99991.jpg
This should have the optimal nozzle-exit-size to distance-to-cup-base ratio based on what I've read.
But all of these dimensions are variable now that I can simply drill out the hole size I want in whatever rod size I want. The next rod size up is 3/64.

I would also like to thank everyone for their feedback. I'm learning way more than I had anticipated.

Re: "Nazca" - Waterblock Concept
 

This is a really neat design. I like how you have the water flowing from the inlet chamber to a 360deg outlet chamber. Very clever. Can't wait to see an actual design. PM me if you want good 3d rendered previz.

Re: "Nazca" - Waterblock Concept
 

Much easier with a rotary table.
They aren't that expensive (think Chinese) and, unless you are magic, your plan on drilling/fixturing/refixturing/more drilling, etc. is not gonna work, especially at the sizes/tolerances we're talking about here.
Seriously....rotary table.

Re: "Nazca" - Waterblock Concept
 

The channel bends and pits are the same bit size and will most likely be done using a programmable mill to save time and effort. Then the lathe work begins, and after that I'll mill the channels.

The mounting holes could be done with a bridgeport or pre-drilled to a smaller size with the programmable mill.

Re: "Nazca" - Waterblock Concept
 

Thread revival!
I'm not sure if I really want to experiment with jet impingement right now and I'm being a cheapskate so I'm trying to revise my design minus the nozzles and pits.

So I'm just going to go with a slightly simplified version that I can make from a 2x2x0.1875" copper scrap. Fin height is 3.16mm and base thickness is 1.5mm (blame inches).
http://www.captainslug.com/modding/nazca-1.jpg

I'm going to be doing all the work myself on a manual mill so I think I'm going to start with something relatively simple. I'll be able to do the 45-degree channels by simply making a mounting block that the base bolts onto. Both barbs will be 3/8" NPT x 1/2"ID tubing.
I have the tools, the time, and the materials. I just need to get back to wrapping my head around this since I've been away for a few months.

Re: "Nazca" - Waterblock Concept
 

looks fun, watch out for the top cover leakage, otherwise its pretty cool

Re: "Nazca" - Waterblock Concept
 

Here's the coverage on a 1.25" IHS
http://www.captainslug.com/modding/nazca-2.jpg
I'll be using a 1-1/2" ID 1-5/8" OD Red-Orange Silicone O-Ring

Re: "Nazca" - Waterblock Concept
 

I've decided to make this a little bit easier on myself by simplifying the machining of the block a little. The new design is a sandwhich of three parts that collectively will be easier to make. It may also alleviate the outlet concerns of the previous revisions,
http://www.captainslug.com/modding/nazca-3.jpg
http://www.captainslug.com/modding/nazca-4.jpg
The plate in the middle will be solvent-adhered to the thick top piece.

Re: "Nazca" - Waterblock Concept
 

nice design but i liked the older revisions more, just try it on a cnc then its no problem with that many bends;).
performance should be on a level with top waterblocks ala rbx/tdx or white water.

it remembers me of a little bit similar block which i did some time ago (the block on the right). Its sandblastet and polished. channels are 8x 1mm*2,5mm
http://davidzo.cooling-store.de/k5/PICT1182k.jpg

Re: "Nazca" - Waterblock Concept
 

I don't have access to CNC. All of the tooling will be done with manual equipment. I've been keeping that in mind with all of my designs so they're all possible to make with manual equipment. The newest revision could work with the older base design, but I'm unsure about being able to add the channel bends with a manual mill.
Sure this would all be much easier with CNC equipment, but I don't know anyone who would help me out for free with that. I already have the materials and free access to the manual mill.

And I haven't mentioned this here yet but I'm also working on my own 1/2" ID 3/4" OD compression fittings.
http://www.captainslug.com/modding/mk6_90.jpg
http://www.captainslug.com/modding/mk6_9996.jpg
I'll do some more thinking about nozzle and channel refinements.

Re: "Nazca" - Waterblock Concept
 

Improvement?
http://www.captainslug.com/modding/nazca-5.jpg
My pump can handle the restriction if I can handle the machining of the base.

Re: "Nazca" - Waterblock Concept
 

why are you making compression fittings on your own? I thought there is a huge selection on the market of those.

The nozzle looks nice, but i believe a nozzle with only holes would perform better. I have a round chamber in the top of the block below and tried different round shaped nozzleplates. The nozzle with only holes was a little better than a nozzle whith slits like a star.

In all i think the block will still be horrible to manufacture with a manual mill, but i would love to see you try it and make it like it looks as a rendering, i would like it even better if it was one of the earlier revisions (latest on page1 looks good).

I have a very small CNC-mill and recently made a version of my K5 which you see in Post #39 with 2mm channels witheout bends instead of the highly restrictive 1mm ones. If you are interested i will show you pics and specs when i am finished with this two blocks. If I had some more free time i would offer you to mill the cooler on my cnc, but that is curently impossible and would also be very complex to redo your drawings in my proprietary CAD/CAM software that i could draw one or two new designs in that time.

Re: "Nazca" - Waterblock Concept
 

My whole loop will be using 1/2" ID 3/4" OD tubing which is not a size that compression fittings are offered for. So I'm making my own out of delrin.

I'm still hedging on whether or not to bother with jet impringement using nozzles and cups but based on your advice I will go with a drilled nozzle pattern rather than the star pattern. The star pattern was solving a machining issue that the new design no longer has.

The only person I've talked to in the states about CNC work is JFettig, and I don't know what software he uses. I'm using Alibre Xpress because it's what the machine shop I go to uses and it's very easy to work with.

Re: "Nazca" - Waterblock Concept
 

The nozzle plate is done.
http://www.captainslug.com/modding/nazca-6.jpg
http://www.captainslug.com/modding/nazca-7.jpg

Re: "Nazca" - Waterblock Concept
 

Hey, nicely done. Compression fittings look interesting as well - do they work as intended?

Re: "Nazca" - Waterblock Concept
 

Actually I screwed up the compression fittings. I couldn't get a working thread on them with the die blocks. So if I want to make them the way I intended them to be I'd have to start over again.
After some fiddling about yesterday I discovered that the collar nuts that I hadn't finished making for the compression fittings make some strangely effective tubing clamps.
http://www.captainslug.com/modding/mk6_9998.jpg
You slip the collar nut around the fitting, slide the tubing onto the fitting, then pull the collar nut onto the tubing like so.
http://www.captainslug.com/modding/mk6_9999.jpg
What I end up with is basically like chinese hand-cuffs. The harder I pull on the tubing, the harder the collar nut clamps the tubing to the fitting. The tubing cannot be pulled off the fitting with the collar inplace because the inner diameter of the collar nut fits the outside of the tubing so precisely that the tubing can't get over the lip on the barb. To unclamp the tubing you just push the collar nut away from the tubing.

I've accidentally made a backwards compression fitting. I want to do some leak testing with these, the pump, and one block later.
If I want to attempt making compression fittings again I'll have to use the lathe to add the thread to the fittings rather than trying to do it with the die blocks.

Re: "Nazca" - Waterblock Concept
 

nice invention. if that works good, why not use it, it sounds very practical

nozzleplate looks good. a picture from the backside would be interesting. why is there a hole in the middle?

Re: "Nazca" - Waterblock Concept
 

The 4 holes in the exact center were a little too fragile. So the center won't have nozzles unless I want to make a new nozzle plate out of brass or delrin. I don't think the center lacking 4 nozzles will really effect anything though so I'm not worried about it.

Re: "Nazca" - Waterblock Concept
 

ah, thats it. I think it will have a noticable negative impact on performance.
There is a guy in germany who made a lot of tests about coolers with nozzles. he tried different nozzle sizes too. In his tests one bigger nozzle in the middle was always a very bad thing and did affect performance a lot. It is a little different setup so it can't be translated to every nozzlesetup, but i think in this case it is agood guess that the bigger nozzle in the middle will affect performance negatively.
Read about it here (german translated with google): http://translate.google.com/translat...language_tools

Re: "Nazca" - Waterblock Concept
 

Alright. Once I get some more label paper I'll make a new one.