Watercooling (almost) done. Pics

HMB · 11-02-2002, 08:34 AM

Heatercore, homemade shroud

, innovatek V3 and an eheim 1048. Gonna get something for the front exhaust, cant look all naked like that

On my bed we have some old shit i used before

The plexiblock is a direct die-block i used before. Didnt work that well, didnt have enough watervelocity.

g.l.amour · 11-03-2002, 10:48 AM

looks like an effective enough setup. but u got some cleaning up to do to get some ou's and aaa's from this difficult crowd ;-)

HMB · 11-03-2002, 10:58 AM

Its coming, its coming. Im not done yet

gmat · 11-03-2002, 02:58 PM

Nice work in that tiny Aopen case.
Did U swap original Innovatek fittings with copper elbows ?

HMB · 11-03-2002, 04:23 PM

Quote:

Originally posted by gmat
Nice work in that tiny Aopen case.
Did U swap original Innovatek fittings with copper elbows ?

Well i replaced innovateks standard fittings with 1/2" brass barbs. Straight ones. Then i put the 90 degree elbows above the barbs.

MadDogMe · 11-04-2002, 03:19 AM

W0W!, that is a skinny case ain't it?. I would'nt use the 90Deg bends though, I'd use silicone (or Tygon?) for them. then you could have had the pump outlet pointing straight at the rad (no kinks!). good work on keeping the tubing lenght down!, it causes more flow loss than I realised till recently....

HMB · 11-04-2002, 10:03 AM

Quote:

Originally posted by MadDogMe
W0W!, that is a skinny case ain't it?. I would'nt use the 90Deg bends though, I'd use silicone (or Tygon?) for them. then you could have had the pump outlet pointing straight at the rad (no kinks!). good work on keeping the tubing lenght down!, it causes more flow loss than I realised till recently....

The case is kinda small

Im too poor to buy silicone or tygon tubing

Nah, (well its kinda true) i dont like silicone tubing. Want the rigid crappy stuff thats cheap and collapses

. Right now i use a 90 degree barb on the pumps exhaust. Thinking about putting the straight barb back and use a 90 degree elbow between the pump and rad....

11-02-2002, 08:34 AM	#1
HMB Cooling Neophyte Join Date: Aug 2002 Location: Sweden Posts: 63	Watercooling (almost) done. Pics Heatercore, homemade shroud , innovatek V3 and an eheim 1048. Gonna get something for the front exhaust, cant look all naked like that On my bed we have some old shit i used before The plexiblock is a direct die-block i used before. Didnt work that well, didnt have enough watervelocity. __________________ Asus A7N8X Deluxe, 2500+@2700MHz (13,5x200), 2x256MB TwinMOS pc3200 @ 2-2-2-11, GFFX 5900 Ultra@500/950MHz, 2x120GB Maxtor Diamondmax 9 8MB SATA raid-0, Prometeia, Logitech z-680. 20000+ 3Dmark2001 Duron 600@1521MHz RIP

11-03-2002, 10:58 AM	#3
HMB Cooling Neophyte Join Date: Aug 2002 Location: Sweden Posts: 63	Its coming, its coming. Im not done yet __________________ Asus A7N8X Deluxe, 2500+@2700MHz (13,5x200), 2x256MB TwinMOS pc3200 @ 2-2-2-11, GFFX 5900 Ultra@500/950MHz, 2x120GB Maxtor Diamondmax 9 8MB SATA raid-0, Prometeia, Logitech z-680. 20000+ 3Dmark2001 Duron 600@1521MHz RIP

11-03-2002, 10:48 AM	#2
g.l.amour Cooling Savant Join Date: Mar 2002 Location: on da case Posts: 933	looks like an effective enough setup. but u got some cleaning up to do to get some ou's and aaa's from this difficult crowd ;-)

11-03-2002, 02:58 PM	#4
gmat Thermophile Join Date: Mar 2001 Location: France Posts: 1,221	Nice work in that tiny Aopen case. Did U swap original Innovatek fittings with copper elbows ?

11-04-2002, 03:19 AM	#6
MadDogMe Thermophile Join Date: Aug 2002 Location: Just shut up ;) ... Posts: 1,068	W0W!, that is a skinny case ain't it?. I would'nt use the 90Deg bends though, I'd use silicone (or Tygon?) for them. then you could have had the pump outlet pointing straight at the rad (no kinks!). good work on keeping the tubing lenght down!, it causes more flow loss than I realised till recently....

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)