Swiftech H20-120 Kit @ 3DGameman

DMOS · 09-18-2004, 02:59 PM

Uh... BillA, I have a question for you? When people do reviews of your products, especially video reviews where you can see what they are doing, aren't they supposed to at least plumb the block properly? Last I checked, according to Swiftech documentation, the center barb was the inlet. Not the offcenter one. As well, since when does a review need 9 minutes of showing how to install the kit, and 30 seconds of discussion on the performance show proper balance? I mean, there was zero discussion on how he got temps, what he used for load, etc etc (the usual beefs). Watching this I felt my intelligence was being insulted.

Video Review

DMOS · 09-18-2004, 04:17 PM

Well, it appears he did follow things as the documentation told him to.

But that picture doesn't quite jive with this:

Am I missing something?

Cathar · 09-18-2004, 04:33 PM

You're quite right. In the first picture the routing is showing this:

pump outlet->reservoir->waterblock outlet->radiator->pump inlet

Someone needs to correct the first diagram.

BillA · 09-18-2004, 04:38 PM

shall be done ASAP

jeez

BillA · 09-19-2004, 04:56 PM

here is the skinny
this dwg was corrected in July (after one week)

not too sure how this got out, but it clearly is incorrect
all about QC again
Thanks DMOS

RedPhoenix · 09-19-2004, 07:18 PM

does it just seem he buys out the companies, no?

DMOS · 09-19-2004, 07:35 PM

Quote:

Originally Posted by unregistered

here is the skinny
this dwg was corrected in July (after one week)

not too sure how this got out, but it clearly is incorrect
all about QC again
Thanks DMOS

No problem. I like to think I've been trained to pay attention to detail when I read/see things, but it still scares me that no one else noticed this first (and spoke up anywhere). Like say, the reviewer himself. Or any of the large number of people who have seen this review before me. At least those within your company got it fixed before it became a widespread issue. On a positive note, it still got an award even being hooked up backwards.

Techmasta · 09-22-2004, 08:27 PM

http://www.3dgameman.com/forums/show...216#post430216

Rodney replied to the thread phaestus, in case you wanted to reply to him again.

09-18-2004, 02:59 PM	#1
DMOS Cooling Neophyte Join Date: Apr 2003 Location: Kingston, ON, Canada Posts: 31	Swiftech H20-120 Kit @ 3DGameman Uh... BillA, I have a question for you? When people do reviews of your products, especially video reviews where you can see what they are doing, aren't they supposed to at least plumb the block properly? Last I checked, according to Swiftech documentation, the center barb was the inlet. Not the offcenter one. As well, since when does a review need 9 minutes of showing how to install the kit, and 30 seconds of discussion on the performance show proper balance? I mean, there was zero discussion on how he got temps, what he used for load, etc etc (the usual beefs). Watching this I felt my intelligence was being insulted. Video Review __________________ http://www.devhardware.com

09-18-2004, 04:17 PM	#2
DMOS Cooling Neophyte Join Date: Apr 2003 Location: Kingston, ON, Canada Posts: 31	Well, it appears he did follow things as the documentation told him to. But that picture doesn't quite jive with this: Am I missing something? __________________ http://www.devhardware.com

09-19-2004, 07:18 PM	#6
RedPhoenix Cooling Savant Join Date: Jun 2003 Location: Florida Posts: 266	does it just seem he buys out the companies, no? __________________ rawr www.mysoarer.com

09-18-2004, 04:33 PM	#3
Cathar Thermophile Join Date: Sep 2002 Location: Melbourne, Australia Posts: 2,538	You're quite right. In the first picture the routing is showing this: pump outlet->reservoir->waterblock outlet->radiator->pump inlet Someone needs to correct the first diagram.

09-18-2004, 04:38 PM	#4
BillA CoolingWorks Tech Guy Formerly "Unregistered" Join Date: Dec 2000 Location: Posts: 2,371.493,106 Posts: 4,440	shall be done ASAP jeez

09-19-2004, 04:56 PM	#5
BillA CoolingWorks Tech Guy Formerly "Unregistered" Join Date: Dec 2000 Location: Posts: 2,371.493,106 Posts: 4,440	here is the skinny this dwg was corrected in July (after one week) not too sure how this got out, but it clearly is incorrect all about QC again Thanks DMOS

09-22-2004, 08:27 PM	#8
Techmasta Cooling Neophyte Join Date: Sep 2003 Location: USA Posts: 74	http://www.3dgameman.com/forums/show...216#post430216 Rodney replied to the thread phaestus, in case you wanted to reply to him again.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)