Silverprop fusion/polarflo TT gpu blocks?

zee bee · 11-25-2004, 04:11 PM

Hey guys, looking for a good gpu block that is NOT danger den.

Anyone use either of these blocks? How would you rate them in terms of flow restriction? (low/med/high/very high/etc)

Just looking for some feedback on these blocks thx!

zee bee · 11-27-2004, 12:31 AM

Ok whatever I am just going to get the Silverprop block :\

Delirious · 11-27-2004, 04:43 PM

I have the polarflo SF gpu block, and have to say the inside is poorly designed. So i ordered as silverprop to replace it, havent recieved it yet though.

ditchpig · 11-27-2004, 06:54 PM

Get the Fusion. I couldn't be happier with my HL! The HL clears ramsinks and still has a lower profile than many GPU blocks. I only lost 1 PCI slot.

Cranky · 11-27-2004, 08:37 PM

i like the swifty mcw50 myself..

zee bee · 11-28-2004, 01:18 AM

Thanks for the suggestions, I am getting the silverprop. Can anyone recommend one of their cpu waterblocks too? i want the whitewater but it is not in stock anywhere. Using a system w/ 1/2" ID tubing

BlackStealth · 11-28-2004, 03:29 AM

Quote:

Originally Posted by ditchpig

Get the Fusion. I couldn't be happier with my HL! The HL clears ramsinks and still has a lower profile than many GPU blocks. I only lost 1 PCI slot.

I also have the SilverProp Fusion HL installed on my 9800Pro, it one of the best GPU blocks out there. I think I over tightened it on my 9800XT and the core is damaged. What technique did you use to install it? I personally used the screw and nut.
Just to avoid the same mistake again

Thanks

zee bee · 11-28-2004, 04:05 AM

^Ouch!!!!^

BlackStealth · 12-02-2004, 03:27 AM

Quote:

Originally Posted by zee bee

^Ouch!!!!^

Yeah It Hurts ! But what could I do , Life just goes on......
So no advice on the installation?

Pooky · 12-02-2004, 01:05 PM

I have a Silverprop Cyclone something (not sure which model it is, it's for P4 and has a red top with a copper base.) I bought it from Criticool off eBay many months ago. I'm not sure what the inside design is, as I haven't taken it apart. My 6800 will have a Swiffy MCW50 soon. Both are non DD solutions

11-25-2004, 04:11 PM	#1
zee bee Cooling Neophyte Join Date: Nov 2004 Location: Florida Posts: 14	Silverprop fusion/polarflo TT gpu blocks? Hey guys, looking for a good gpu block that is NOT danger den. Anyone use either of these blocks? How would you rate them in terms of flow restriction? (low/med/high/very high/etc) Just looking for some feedback on these blocks thx!

11-27-2004, 12:31 AM	#2
zee bee Cooling Neophyte Join Date: Nov 2004 Location: Florida Posts: 14	Ok whatever I am just going to get the Silverprop block :\

11-27-2004, 04:43 PM	#3
Delirious Cooling Savant Join Date: Oct 2004 Location: Twilight Zone Posts: 152	I have the polarflo SF gpu block, and have to say the inside is poorly designed. So i ordered as silverprop to replace it, havent recieved it yet though.

11-27-2004, 06:54 PM	#4
ditchpig Cooling Neophyte Join Date: May 2004 Location: Vic BC, Cal AB Posts: 3	Get the Fusion. I couldn't be happier with my HL! The HL clears ramsinks and still has a lower profile than many GPU blocks. I only lost 1 PCI slot.

11-27-2004, 08:37 PM	#5
Cranky Cooling Neophyte Join Date: Jun 2004 Location: texas Posts: 92	i like the swifty mcw50 myself..

11-28-2004, 01:18 AM	#6
zee bee Cooling Neophyte Join Date: Nov 2004 Location: Florida Posts: 14	Thanks for the suggestions, I am getting the silverprop. Can anyone recommend one of their cpu waterblocks too? i want the whitewater but it is not in stock anywhere. Using a system w/ 1/2" ID tubing

11-28-2004, 04:05 AM	#8
zee bee Cooling Neophyte Join Date: Nov 2004 Location: Florida Posts: 14	^Ouch!!!!^

12-02-2004, 01:05 PM	#10
Pooky Cooling Neophyte Join Date: Mar 2004 Location: Oregon (soon) Posts: 12	I have a Silverprop Cyclone something (not sure which model it is, it's for P4 and has a red top with a copper base.) I bought it from Criticool off eBay many months ago. I'm not sure what the inside design is, as I haven't taken it apart. My 6800 will have a Swiffy MCW50 soon. Both are non DD solutions

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)