Dumb question

wshost.Shorty · 05-15-2004, 11:25 PM

Hi im not a wcing guru like most of you here, but i know SOME stuff...anyways on to the Stupid Question!

RBX or TDX?

when running a tline>pump>dbl hc> block setup with 1/2 tubing in Arizona...probably on a Intel 2.8c

so RBX or TDX? Why? Thanks so much!

You guy rock!

Groth · 05-16-2004, 12:48 AM

If half your tubing is in Arizona, where's the the other half?

j/k

I'd say the TDX, simply because it will cover the entire IHS.

pHaestus should have nozzle data available shortly; should make the decision easier.

trit187 · 05-16-2004, 01:16 AM

what pump? looks like the tdx is less restrictive.. so it could make a difference

wshost.Shorty · 05-16-2004, 01:21 AM

Ehiem 1250...anyone else?

wshost.Shorty · 05-16-2004, 06:05 PM

Also, If i order the ehiem from dangerden, i dont need them to modify it? just keep it as is...

After reading this: http://www.ocforums.com/showthread.p...=1250+and+mag3

Am I correct?

kronchev · 05-17-2004, 12:30 PM

get the danner mag 3 if you dont mind putting barbs on, which is all of wrapping the male threads in teflon tape, screwing them on as best as theyll go, then sealing under them for some added protection

wshost.Shorty · 05-17-2004, 12:50 PM

Quote:

Originally Posted by kronchev

get the danner mag 3 if you dont mind putting barbs on, which is all of wrapping the male threads in teflon tape, screwing them on as best as theyll go, then sealing under them for some added protection

I'll think ill stay with the ehiem...any other ideas concerning the block type?

kronchev · 05-17-2004, 01:19 PM

Quote:

Originally Posted by wshost.Shorty

I'll think ill stay with the ehiem...any other ideas concerning the block type?

all tests have shown the TDX comes out on top

wshost.Shorty · 05-17-2004, 01:28 PM

I liked it more any way

Still open for more suggestions/comments

Thanks.

05-15-2004, 11:25 PM	#1
wshost.Shorty Cooling Neophyte Join Date: Feb 2004 Location: California Posts: 19	Dumb question Hi im not a wcing guru like most of you here, but i know SOME stuff...anyways on to the Stupid Question! RBX or TDX? when running a tline>pump>dbl hc> block setup with 1/2 tubing in Arizona...probably on a Intel 2.8c so RBX or TDX? Why? Thanks so much! You guy rock!

05-16-2004, 12:48 AM	#2
Groth Cooling Savant Join Date: Mar 2003 Location: MO Posts: 781	If half your tubing is in Arizona, where's the the other half? j/k I'd say the TDX, simply because it will cover the entire IHS. pHaestus should have nozzle data available shortly; should make the decision easier. Last edited by Groth; 05-16-2004 at 01:22 AM.

05-16-2004, 01:21 AM	#4
wshost.Shorty Cooling Neophyte Join Date: Feb 2004 Location: California Posts: 19	Ehiem 1250...anyone else? Last edited by wshost.Shorty; 05-16-2004 at 05:51 PM.

05-17-2004, 12:30 PM	#6
kronchev Cooling Savant Join Date: Mar 2004 Location: Lawrenceville, NJ Posts: 254	get the danner mag 3 if you dont mind putting barbs on, which is all of wrapping the male threads in teflon tape, screwing them on as best as theyll go, then sealing under them for some added protection __________________ Ghetto riggin'!

05-16-2004, 01:16 AM	#3
trit187 Cooling Savant Join Date: May 2003 Location: shanghai, china Posts: 200	what pump? looks like the tdx is less restrictive.. so it could make a difference

05-16-2004, 06:05 PM	#5
wshost.Shorty Cooling Neophyte Join Date: Feb 2004 Location: California Posts: 19	Also, If i order the ehiem from dangerden, i dont need them to modify it? just keep it as is... After reading this: http://www.ocforums.com/showthread.p...=1250+and+mag3 Am I correct?

05-17-2004, 01:28 PM	#9
wshost.Shorty Cooling Neophyte Join Date: Feb 2004 Location: California Posts: 19	I liked it more any way Still open for more suggestions/comments Thanks.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)