Insulation for the top of the chip

Titan151 · 06-07-2004, 01:55 AM

Hi,

I recently got a new xp 2600 mobile that I want to prep for my chiller. On my last chip I sprayed conformal coating on the top of the chip and this covered all of it excluding the die. I planned on using neoprene for this but could not get any that was thin enough to prevent the wb from sitting flush. What is the prefered method for insulating the top of the chip as I am hesitant to use the conformal coating method again? The conformal coating I used is like a spray paint. Most sites with info on insulation show a bottle of liquid instead.

I have read numerous site descriptions on how to do this but none were too clear as to the top of the chip. One other problem with neoprene that I had was I was worried about getting a good seal between the die and the neoprene. Or for that matter making sure the neoprene didn't squish out into the die area and shield it from the waterblock.

Thanks for the help.

SlaterSpeed · 06-07-2004, 08:00 AM

Use a layer of dielectric grease

AngryAlpaca · 06-07-2004, 08:31 AM

Quote:

What is the prefered method for insulating the top of the chip as I am hesitant to use the conformal coating method again?

This is SO going into my signature.

Titan151 · 06-07-2004, 09:32 AM

ack,

If your putting it in your sig let me create a post titled "What pump should I Buy"

I bet you will find something better there.

kronchev · 06-07-2004, 10:17 AM

youre thinking too much. you dont put so much neoprine that its right against the die and is in danger of squishing out. you put it around the perimeter a little inwards. make sure to use dielectric grease liberally though.

06-07-2004, 01:55 AM	#1
Titan151 Cooling Savant Join Date: Apr 2004 Location: Seattle Posts: 116	Insulation for the top of the chip Hi, I recently got a new xp 2600 mobile that I want to prep for my chiller. On my last chip I sprayed conformal coating on the top of the chip and this covered all of it excluding the die. I planned on using neoprene for this but could not get any that was thin enough to prevent the wb from sitting flush. What is the prefered method for insulating the top of the chip as I am hesitant to use the conformal coating method again? The conformal coating I used is like a spray paint. Most sites with info on insulation show a bottle of liquid instead. I have read numerous site descriptions on how to do this but none were too clear as to the top of the chip. One other problem with neoprene that I had was I was worried about getting a good seal between the die and the neoprene. Or for that matter making sure the neoprene didn't squish out into the die area and shield it from the waterblock. Thanks for the help.

06-07-2004, 08:00 AM	#2
SlaterSpeed Cooling Savant Join Date: Nov 2003 Location: Suffolk, UK Posts: 234	Use a layer of dielectric grease __________________ aka. slater3333uk - The self proclaimed 'Middle Player' 'Liquified'

06-07-2004, 10:17 AM	#5
kronchev Cooling Savant Join Date: Mar 2004 Location: Lawrenceville, NJ Posts: 254	youre thinking too much. you dont put so much neoprine that its right against the die and is in danger of squishing out. you put it around the perimeter a little inwards. make sure to use dielectric grease liberally though. __________________ Ghetto riggin'!

06-07-2004, 09:32 AM	#4
Titan151 Cooling Savant Join Date: Apr 2004 Location: Seattle Posts: 116	ack, If your putting it in your sig let me create a post titled "What pump should I Buy" I bet you will find something better there.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)