Just wanna show of my rig (lotsapics,beware)

mighty1 · 06-13-2001, 03:03 PM

Okay just wanna show off my lil watercooling.
lets have a look at the pics then.

Ok it started like this

Then it ended up like this.

first some ducting going on here.

it fits..!...w00t, hmm I wonder were i got this idea...

close up, dont mind the kitchen towel on the vid card, no it aint wet, but just to be safe. it hasnt leaked yet so thats gone.

Im using an EHEIM 1048, 600 l/h pump for this inline setup.

120mm BlowHole, to get rid of the hot hd air thats floating around up there.

I need to get something to put in front of that radiator, im trying to get some really fine mesh, no luch on that yet.

I used hammerite spray paint on that mofo, even though its meant for metal the finish holds up nice on the front bezel.

Its a Abit kT7-R with a duron 700@950 @1.825V (not stable at 1G yet) maybe after i get a pelt on tha bi@ch.
Swiftech MCW-462 block and some radiator I picked up at the cardump.

Im getting okay temps right now
full load 40c (supaorb 52c)
idle bout 30c
this was with ambient temps ofbout 30c
its a bit cooler now, 22c ambient,
idle 27c
stress 30c

Its never done, aint it fun heheheh.

YardPig · 06-13-2001, 03:38 PM

I like it! Quite the maze of hoses.
I just finished my watercooler setup.
Homemade waterblock
Danner 250GPH pump
Suzuki LJ80 heatercore
1/2ID hose throughout
This thing flows like the north sea.
A7V133 2.1V
Duron 700 only stable to 978 with air.

Water is a whole other story.

Yeeeeeeeaaaaah baby!!

I am memory limited at this time with a max of 140 on generic pc133.

Again, nice work on your system.

Take care

06-13-2001, 03:03 PM	#1
mighty1 Cooling Neophyte Join Date: Jun 2001 Location: Netherlands Posts: 1	Just wanna show of my rig (lotsapics,beware) Okay just wanna show off my lil watercooling. lets have a look at the pics then. Ok it started like this Then it ended up like this. first some ducting going on here. it fits..!...w00t, hmm I wonder were i got this idea... close up, dont mind the kitchen towel on the vid card, no it aint wet, but just to be safe. it hasnt leaked yet so thats gone. Im using an EHEIM 1048, 600 l/h pump for this inline setup. 120mm BlowHole, to get rid of the hot hd air thats floating around up there. I need to get something to put in front of that radiator, im trying to get some really fine mesh, no luch on that yet. I used hammerite spray paint on that mofo, even though its meant for metal the finish holds up nice on the front bezel. Its a Abit kT7-R with a duron 700@950 @1.825V (not stable at 1G yet) maybe after i get a pelt on tha bi@ch. Swiftech MCW-462 block and some radiator I picked up at the cardump. Im getting okay temps right now full load 40c (supaorb 52c) idle bout 30c this was with ambient temps ofbout 30c its a bit cooler now, 22c ambient, idle 27c stress 30c Its never done, aint it fun heheheh.

06-13-2001, 03:38 PM	#2
YardPig Cooling Neophyte Join Date: May 2001 Location: Earth Posts: 21	I like it! Quite the maze of hoses. I just finished my watercooler setup. Homemade waterblock Danner 250GPH pump Suzuki LJ80 heatercore 1/2ID hose throughout This thing flows like the north sea. A7V133 2.1V Duron 700 only stable to 978 with air. Water is a whole other story. Yeeeeeeeaaaaah baby!! I am memory limited at this time with a max of 140 on generic pc133. Again, nice work on your system. Take care

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)