Pelts Help and Block help

Jolinator · 11-17-2001, 10:30 PM

Hey im not a newbie to watercooling but just am puzzled as to which block to choose.
the thing is im going to use a 220watt TEC with it and i want something that has a bolt down cold plate and not the maze 2 as its huge and would be a bitch to insulate like this
then i looked @ the swiftec and swore because the little nipples are piss weak and i have 1/2 so i dont no what to do there and also its cu and AL will the anodising stop the corosion with water wetter? but its very nice coz the insulation kit rox and shit

also what temp do u think i will get with the following

1.eden 128g 1150ltr pump but rox for pumping through flow restriction
2.black ice Extreme with a 69cfm panaflow on it and a black ice normal with a 62cfm i think? JMC 25mm fan on it dont ask why im using a bice 1 as its the inly one that fits were i want it
3.what ever block u reccomend
4.220watt tec running full steam
5.room temp of 23-24

??

Butcher · 11-17-2001, 11:26 PM

maze2-2, huge it may be but it is a quality block.
as for full steam on the tec, bad plan, run it at about 75-85%, they work better.

Jolinator · 11-18-2001, 05:22 AM

thats what i meant
i knew that

as the heat/cooling ratio is better

thanks anyway tho

Brad · 11-19-2001, 05:17 PM

You might want to consider the maze1c1, if you want a smaller block, it does use bolts to clamp the pelt down

11-17-2001, 10:30 PM	#1
Jolinator Cooling Neophyte Join Date: Jun 2001 Posts: 23	Pelts Help and Block help Hey im not a newbie to watercooling but just am puzzled as to which block to choose. the thing is im going to use a 220watt TEC with it and i want something that has a bolt down cold plate and not the maze 2 as its huge and would be a bitch to insulate like this then i looked @ the swiftec and swore because the little nipples are piss weak and i have 1/2 so i dont no what to do there and also its cu and AL will the anodising stop the corosion with water wetter? but its very nice coz the insulation kit rox and shit also what temp do u think i will get with the following 1.eden 128g 1150ltr pump but rox for pumping through flow restriction 2.black ice Extreme with a 69cfm panaflow on it and a black ice normal with a 62cfm i think? JMC 25mm fan on it dont ask why im using a bice 1 as its the inly one that fits were i want it 3.what ever block u reccomend 4.220watt tec running full steam 5.room temp of 23-24 ??

11-17-2001, 11:26 PM	#2
Butcher Thermophile Join Date: May 2001 Location: UK Posts: 1,064	maze2-2, huge it may be but it is a quality block. as for full steam on the tec, bad plan, run it at about 75-85%, they work better. __________________ Once upon a time, in a land far far away...

11-19-2001, 05:17 PM	#4
Brad Thermophile Join Date: Oct 2001 Location: Nuu Zeeelin Posts: 3,175	You might want to consider the maze1c1, if you want a smaller block, it does use bolts to clamp the pelt down __________________ 2x P3 1100's at 1400, Abit VP6, 2x Corsair 256mb PC150 sticks, 20gb 'cuda ATA-III, 2x 40gb 'cuda ATA-IV in raid 0. 20" Trinitron. No fans 2x 2400+ at 2288mhz (16.0 x 143), Iwill MPX2, 2x Kingmax PC-3200 256mb sticks, 4x 20gb 60gxp in Raid 5 on a Promise SX6000. Asus Ti4200 320/630. Cooled by Water

11-18-2001, 05:22 AM	#3
Jolinator Cooling Neophyte Join Date: Jun 2001 Posts: 23	thats what i meant i knew that as the heat/cooling ratio is better thanks anyway tho

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)